2022 SUZUKI JIMNY main

EMERGENCY SERVICE
If the high engine coolant temperature warning light does not go off or the tem­perature indication does not come down to within the normal, acceptable range:
1) Turn off the engine and check that the water pump belt and pulleys are not damaged or slipping. If any abnormality is found, correct it. 2) Check the coolant level in the reservoir. If it is found to be lower than "LOW" line, check radiator, water pump, radia­tor hoses and heater hoses for leakage. If leakage that may cause overheating is found, do not run the engine until these problems have been corrected. 3) If leakage is not found, carefully add coolant to the reservoir and then the radiator, if necessary. (Refer to "Engine coolant" in "INSPECTION AND MAIN­TENANCE" section.)
NOTE: If engine overheats and you are not sure what to do, contact a SUZUKI dealer.
7-11
650614
A WARNING
• It is hazardous to remove the radia­tor cap when the water temperature is high, because scalding fluid and steam may be blown out under pressure. The cap should only be taken off when the coolant tem­perature has lowered. To help prevent personal injury, keep hands, tools and clothing away from the engine cooling fan and air-conditioner fan. These elec­tric fans can automatically turn on without warning.

APPEARANCE CARE
Corrosion prevention
It is_ important to take good care of your vehicle to protect it from corrosion. Listed below are instructions for how to maintain your vehicle to prevent corrosion. Please read and follow these instructions carefully.
Important information about corro­
sion
Common causes of corrosion 1) Accumulation of road salt, dirt moisture or chemicals in hard-to-reach areas of the vehicle underbody or frame. 2) Chipping, scratches and any damage to treated or painted metal surfaces resulting from minor accidents or abra­sion by stones and gravel.
Environmental conditions which accel­erate corrosion 1) Road salt, dust control chemicals, sea breeze or industrial pollution will all accelerate the corrosion of metal. 2) High humidity will increase the rate of corrosion particularly when the tem­perature range is just above the freez­ing point. 3) Moisture in certain areas of a vehicle for an extended period of lime may pro­mote corrosion even though other body sections may be completely dry.
8-1
4) High temperatures will cause an accel­erated rate of corrosion to parts of the vehicle which are not well-ventilated to permit quick drying.
This information illustrates the necessity of keeping your vehicle (particularly the ~nderbody) as clean and dry as possible. It Is equally important to repair any damage to the paint or protective coatings as soon as possible.
How to help prevent corrosion
Wash your vehicle frequently The_ best way to preserve the finish on your vehicle and to help avoid corrosion is to keep it clean with frequent washing. Wash your vehicle at least once during the winter and once immediately after the win­ter. K<:ep your vehicle, particularly the underside, as clean and dry as possible. If you frequently drive on salted roads your vehicle should be washed at least once a month during the winter. If you live near the ocean, your vehicle should be washed at least once a month throughout the year.
For washing instructions, refer to "Vehicle cleaning" section.
Remove foreign material deposits Foreign materials such as salts chemicals road oil or tar, tree sap, bird droppings and industnal fall-out may damage the finish of your vehicle if it is left on painted surfaces. Remove these types of deposits as quickly as possible. If these deposits are difficult to wash off, an additional cleaner may be required. Check that any cleaner you use is not harmful to painted surfaces and is specifically intended for your purposes. Follow the manufacturer's directions when using these special cleaners.
Repair finish damage Carefully examine your vehicle for damage to the painted surfaces. Should you find any chip~ or scratches in the paint, touch them up 1mmed1ately to prevent corrosion from starting. If the chips or scratches have gone through to the bare metal have a qualified body shop make the rep~ir.
Keep passenger and luggage compart­ments clean Moisture, dirt or mud can accumulate under the floor mats and may cause corro­sion. Occasionally, check under these mats to ensure that this area is clean and dry. More fr~quent checks are necessary if the vehicle Is used for off-road driving or in wet weather. Certain cargos such as chemicals, fertiliz­ers, cleaners, salts, etc. are extremely cor­rosive by nature. These products should be transported in sealed containers. If they

APPEARANCE CARE
Cleaning interior
Vinyl upholstery Prepare a solution of soap or mild deter­gent dissolved in warm water. Apply the solution to the vinyl with a sponge or soft cloth and let it soak for a few minutes to loosen dirt. · Rub the surface with a clean, damp cloth to remove dirt and the soap solution. If some dirt still remains on the surface, repeat this procedure.
Fabric upholstery Remove loose dirt with a vacuum cleaner. Using a mild soap solution, rub stained areas with a clean damp cloth. To remove soap, rub the areas again with a cloth dampened with water. Repeat this until the stain is removed, or use a commercial fab­ric cleaner for tougher stains. If you use a fabric cleaner, carefully follow the manu­facturer's instructions and precautions.
Leather upholstery Remove loose dirt with a vacuum cleaner. Using a mild soap or saddle soap solution, wipe dirt off with a clean damp soft cloth. To remove soap, wipe the areas again with a soft cloth dampened with water. Wipe the areas dry with a soft dry cloth. Repeat this until the dirt or stain is removed, or use a commercial leather cleaner for tougher dirt or stains. If you use a leather cleaner, carefully follow the manufacturer's instruc­tions and precautions. Do not use solvent type cleaners or abrasive cleaners.
NOTE: In order to keep leather upholstery look­ing good, it should be cleaned at least twice a year. If leather upholstery becomes wet, immediately wipe it dry with tissue paper or a soft cloth. Water may cause leather to harden and shrink if it is not wiped off. When parking on sunny days, select a shady place or use a sunshade. If leather upholstery is exposed to direct sunlight for a long time, it may disco/or and shrink. As is common with natural materials, leather is inherently irregular in grain and cowhide has spots in its natural state. These do not affect the performance of the leather in any way.
Seat belts Clean seat belts with a mild soap and water. Do not use bleach or dye on the belts. They may weaken the fabric in the belts.
Vinyl floor mats Ordinary dirt can be removed from vinyl with water or mild soap. Use a brush to help loosen dirt. After the dirt is loosened, rinse the mat thoroughly wtth water and dry it in the shade.
Carpets Remove dirt and soil as much as possible with a vacuum cleaner. Using a mild soap solution, rub stained areas with a clean damp cloth. To remove soap, rub the areas again with a cloth dampened with water. Repeat this until the stain is removed, or use a commercial carpet cleaner for tougher stains. If you use a carpet cleaner, carefully follow the manufacturer's instruc­tions and precautions.
Instrument panel and console Remove loose dirt with a vacuum cleaner. Gently wipe dirt off with a tightly squeezed damp clean cloth. Repeat this until the dirt is removed.

NOTICE
Do not use chemical products that contain silicon to wipe electrical components such as the air condi­tioning system, audio1 navigation system, or other switches. These will cause damage to the components.
NOTICE
Liquid such as liquid aromatics, soft drinks or juice may cause dis­coloration, wrinkles, and cracking to resin-based parts and textiles. Immediately wipe it dry with tissue paper or a soft cloth. Do not leave leather products with color, fur or vinyl products, etc. in your vehicle for long periods. It may cause discoloration or deterio­ration of interior.
Cleaning exterior
NOTICE
It is important that your vehicle be kept clean and free from dirt. Failure to keep your vehicle clean may result in fading of the paint or corrosion to various parts of the vehicle body.
Caring for aluminum wheels
NOTE: Do not use an acidic or alkaline deter­gent, or a cleaner containing petroleum solvent to wash aluminum wheels. These types of cleaner will cause per­manent spots, disco/oration and cracks on finished surfaces and damage to cen­ter caps. Do not use a bristle brush and soap con­taining an abrasive material. These will damage finished surfaces.
APPEARANCE CARE
Washing
A WARNING
Never attempt to wash and wax your vehicle with the engine run­ning. When cleaning the underside of the body and fender, where there may be sharp-edged parts, wear gloves and a long-sleeved shirt to protect your hands and arms from being cut. After washing your vehicle, care­
fully test the brakes before driving to check that they have maintained their normal effectiveness.
8-4

SPECIFICATION
ITEM: Mass (weight) UNIT: kg (lbs)
Curb mass (weight) MIT 1080-1095 (2381-2414)
A/T 1095-1110 (2414-2447)
Gross vehicle mass (weight) rating 1435 (3163)
Permissible maximum Axle Weight Front 680 (1499)
Rear 880 (1940)
ITEM: Engine
Type K15B
Number of cylinders 4
Bore 74.0 mm (2.91 in.)
Stroke 85.0 mm (3.35in.)
Piston displacement 1462 cm3 (1462 cc, 89.2 cu.in)
Compression ratio 10.0: 1
ITEM: Electrical
Standard spark plug DENSO ZXU20PR11, NGK KR6A-10
Battery 12V 55B24L 20HR 45AH CCA 370A(JIS)
Fuses See "INSPECTION AND MAINTENANCE" section.
9-4

INDEX
Listening to a CD ................................................................. 5-48
Listening to an iPod ............................................................ 5-58
Listening to an MP3/WMA/AAC disc .................................. 5-51
Listening to files stored in a USB device .......................... 5-55
Listening to the radio ................................................. 5-41, 5-43
Low engine coolant temperature light (blue color) .......... 2-48
Low fuel warning light ......................................................... 2-47
Low tyre pressure warning light ............................... 2-39, 3-64
M
Main beam (high beam) indicator light .............................. 2-52
Maintenance recommended under severe
driving conditions .............................................................. 10-25
Maintenance recommended under severe
driving conditions (except for EU countries and Israel) .... 6-8
Maintenance recommended under severe
driving conditions (for EU countries and Israel) .............. 6-18
Maintenance schedule .......................................................... 6-2
Malfunction indicator light .................................................. 2-45
Manual heating and air conditioning system .................... 5-17
Manual transmission ............................................................. 3-8
Master warning indicator light ............................................ 2-54
Mirrors .................................................................................. 2-13
0
Odometer ..................................................................... 2-20, 2-32
Oil change reminder light ................................................... 2-53
Oil filter replacement ........................................................•.. 6-27
Oil level check ...................................................................... 6-24
Oil pressure light ...................................•.................•........... 2-44
Open door warning light ..................................................... 2-47
Outside rearview mirrors ..........................•......................... 2-13
Outside rearview mirrors folding switch ........................... 2-14
11-4
p
Parking brake ....................................................................... 6-35
Parking brake lever ................................................................ 3-5
Pedal ........•............................................................................... 3-6
Periodic maintenance schedule
(except for EU countries and lsrael) ..................................... 6-3
Periodic maintenance schedule
(for EU countries and Israel) ............................................... 6-13
Pinching prevention function ............................................. 2-12
Power-assisted brakes ........................................................ 3-53
R
Radio antenna ...................................................................... 5-30
Raising vehicle with garage jack .......................................... 7-3
RDS (Radio Data System) .................................................... 5-45
Rear combination light ........................................................ 6-51
Rear differential oil.. ............................................................. 6-31
Rear fog light indicator light ............................................... 2-53
Rear fog light switch ............................................................ 2-60
Rear passenger's seat belt reminder light... ...................... 2-45
Rear seats ............................................................................... 1-5
Rear window wiper/washer switch ..................................... 2-69
Refill with oil and oil leakage check ................................... 6-28
Refilling ................................................................................. 6-25
Remote audio controls ........................................................ 5-74
Replacing tyres and/or wheels ........................................... 3-71
Running-in .............................................................................• 4-8
s
Seat adjustment ..................................................................... 1-2
Seat belt inspection ............................................................. 1-17
Seat belt pretensioner system ............................................ 1-33
Seat belt reminder ................................................................ 1-15

No.Using Conditions • When temperature under -40-C . • On miring or sand ground . • On big gradient road . • In extreme nature condition: rainstorm, typhoon, cyclone, snowstorm, thunder•storm. etc . • Loading dangerous heavy, for instance: melted metal. acidity substance, radioactivity substance or specially crisp goods • • Contact with hood directly . • Using on boat. • The ground with difference in level.
Operation Instructions Whenever a wheel is changed, always remove any corrosion that may be present on inside of wheel and wheel mounting surface on vehicle. Details: Please operate according to the "operation instructions", Operate the jack on the level ground while checking the jack and the load. Musln"I operate under raising load, unless the load is fastened surely . • Park the car on the nat, love ground and apply the brake firmly. • Set transmission in "reverse"(automalic transmission in ·park") . • Turn on the hazard warning Hasher . • Remove jacklng tools and spare tire from stowage area . • Block fFont and rear of wheel diagonally opposlte wheel being removed before operating jack .
~
ITT
~ .s,.Cl(Jf>Of'(llITT J-'CKIW ~ • Loosen, but do not remove wheel nuts by turning wrench counter clockwise • • Raise jack until Jack-head groove fits boss or frame see Illustrations . • Operate jack with slow, smooth motion, using Jack handle . • Raise vehicle so an innated lire will just clear surface, remove nuts and wheel. • Install wheel, then slightly tighten each nut, wheel must be seated on hub . • lower vehicle, and fully tighten wheel nuts In across-cross sequence by turning wrench clockwise.
Maintenance • Please prevent the JACK SCREW from accretion of dirt . • Check the nameplate, keep the shape same as original. • No-re jigger the Jack's construction privately . • After any use, consult immediately your Suzuki Dealer or Service Partner for inspection and maintenance of the jack . • If the label (slicker) is damaged, pt ease consult your Suzuki Dealer or Service Partner.

SERVICE STATION INFORMATION
Fuel recommendation:
See page 9-2
For EU countries and Israel:
Classification: ACEAA1/B1, A3/B3, A3/B4, A5/B5
API SL, SM, SN
ILSAC GF-3, GF-4, GF-5
Viscosity: SAE 0W-16, 0W-20, 5W-30
Except for EU countries and Israel:
Classification: SG, SH, SJ, SL, SM, or SN
Viscosity: SAE 0W-20, 5W-30, 1 0W-30, 1 0W-40, 1 SW-40,
20W-40
For further details, see "Engine Oil and Filter" in the
"INSPECTION AND MAINTENANCE" section.
$SUZUKI
Brake fluid:
DOT3 or SAE J1703
Automatic transmission fluid:
SUZUKI ATF3317 or Mobil ATF3309 or equivalent to
DEXRON® -Ill.
Tire cold pressure:
See the "Tire Information Label" located on the
driver's door lock pillar.
llllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllll 99011-78RB5-01 E
SUZUKI MOTOR CORPORATION Part No. 99011-78RB5-01E June, 2019 Printed in Japan