2022 MERCEDES-BENZ EQC SUV heating

S
S
t
tatus of t
atus of t he
he
c
c har
har ging
ging
pr
pr ocess
ocess 2
2 Displ
ay
Display Meaning
Meaning
# Lights up
orangeInter
ruption in
ch arging
# Lights up
green Charging
process com-
ple
ted
# Flashesred
(for appr ox.
90 s) Ve
hicle mal-
function;
ch arging is
not possible S S
t
tar
ar ting t
ting t he alt
he alt er
ernating curr
nating curr ent c
ent char
harging pr
ging pr ocess
ocess
(mode 2/3)
(mode 2/3) &
D
DAN
AN GER
GER Risk of death when charging at a
damaged soc ket
The charging process uses high voltage. If
th ech arging cable, theve hicle soc ket or the
mains soc ket are damaged, you could receive
an elect ric shoc k. #
Only use an undamaged charging cable. #
Avoid mechanical damage such as crush-
ing, abrading or driving overth e cable. #
Have a damaged vehicle soc ketre placed
at a quali/ed specialist workshop as
soon as possible. #
Never connect thech arging cable to a
damaged vehicle soc ket. *
N
NOOTE
TE Damage due toove rheating of
ch arging cable and charging cable con-
nector During
thech arging process, thech arging
cable and charging cable connector can heat
up within their permissible limit values. The permissible limit
values are in0uenced by
th efo llowing factors:
R the po wer supply system and thech arging
cable are not damaged
R the inst ructions for handling thech arging
cable and the control element on the
ch arging cable ha vebeen obser ved #
Ifth ech arging cable or charging cable
connector becomes too hot, ha vethe
po we r supply system checked. *
N NOOTE TE Damaged or dirty vehicle soc ket
when the soc ket 0ap is open #
Alwayske ep the soc ket co ver and the
soc ket 0ap closed when there is no
ch arging cable connected. This pr otects
th eve hicle soc ket from dirt and damage. #
Make sure that the soc ket co ver is
closed proper lybefore closing the soc ket
0ap. This can otherwise result in damage
which may pr event the soc ket 0ap from
being opened again. 176
176
Driving and parking

#
Remo vethech arging cable connector from
th eve hicle soc ket within 30 seconds.
ATer the 30 seconds ha veelapsed, theve hicle
soc ket will be loc ked again.
% Ifyo u cannot remo vethech arging cable con-
nector, repeat the unlocking procedure. If the
ch arging cable connector is still loc ked, con-
ta ct a quali/ed specialist workshop. #
Close the soc ket co ver and the soc ket 0ap. #
Remo vethech arging cable connector from
th e mains soc ket, or from the soc ket on the
wa llbox/charging station, and st owtheve hi-
cle's charging cable safely in theve hicle
(/ page 167).
% ATer thech arging cable connector has been
disconnected, the% indicator lamp 1on
th eve hicle soc ketre mains lit for some time
before switching o.. S
S
t
tar
ar ting t
ting t he dir
he dir ect curr
ect curr ent c
ent char
harging pr
ging process ocess
(mode 4)
(mode 4) &
D
DAN
AN GER
GER Risk of death when charging at a
damaged soc ket
The charging process uses high voltage.
If th ech arging cable, theve hicle soc ket or the
mains soc ket are damaged, you could receive
an elect ric shoc k. #
Only use an undamaged charging cable. #
Avoid mechanical damage such as crush-
ing, abrading or driving overth e cable. #
Have a damaged vehicle soc ketre placed
at a quali/ed specialist workshop as
soon as possible. #
Never connect thech arging cable to a
damaged vehicle soc ket. *
N
NOOTE
TE Damage due toove rheating of
ch arging cable and charging cable con-
nector During
thech arging process, thech arging
cable and charging cable connector can heat
up within their permissible limit values.
The permissible limit values are in0uenced by
th efo llowing factors:
R the po wer supply system and thech arging
cable are not damaged
R the inst ructions for handling thech arging
cable and the control element on the
ch arging cable ha vebeen obser ved #
Ifth ech arging cable or charging cable
connector becomes too hot, ha vethe
po we r supply system checked. *
N
NOOTE
TE Damaged or dirty vehicle soc ket
when the soc ket 0ap is open #
Alwayske ep the soc ket co ver and the
soc ket 0ap closed when there is no 180
180
Driving and parking

#
Activate or deactivate the function.
If AT TENTION ASSIST de tects fatigue or
increasing lack of attention, it suggests a rest
area in the vicinity. #
Select the suggested rest area.
Yo u are guided tothe selected rest area. Cr
Cr
uise contr
uise control and limit ol and limit er
er F
F
unction of cr
unction of cr uise contr
uise controlol
Cruise control regula testh e speed totheva lue
selected bythe driver.
If yo u accelerate toove rtake, fore xamp le,the
stored speed is not dele ted. If youre mo veyour
fo ot from the accelerator pedal aTer overtaking,
cruise cont rol will resume speed regulation back
to the stored speed.
Yo u can store any speed abo ve20 km/h up tothe
maximum design speed, up tothe speed recom-
mended byrange moni toring or up tothe set win-
te r tyre limit.
Obser vethe no tes on driving systems and your
re sponsibility; you may otherwise failto recognise
dangers (/ page 191). Display Display
s in t s in the Ins
he Ins tr
trument Display
ument Display
R h (gre y): cruise control is selected but not
yet activated.
R h (gre en): cruise control is active.
A stored speed appears along with theh dis-
pla y.
% The segments extending from the cur rent
stored speed tothe end of the scale, or tothe
set winter tyre limit, light up in the speedome-
te r.
Syst Syst em limits em limits
Cruise control may be unable tomaintain the
stored speed on uphill gradients. The stored
speed is resumed when thegr adient evens out.
Increase recuperation in good time on long and
steep downhill gradients. Take particular no teof
th is when driving a laden vehicle. By doing so, you
will make use of the electric mo tor's braking
e.ect tocharge the high-voltage batter y.This
re lie vesth e load on the brake system and pre-
ve nts the brakes from overheating and wearing
to oqu ickl y. Do not use cruise control in
thefo llowing situa-
tions:
R in tra1c situations which requ ire frequent
ch anges of speed, e.g. in heavy tra1c, on
winding roads
R on slippery roads. Accelerating can cause the
drive wheels tolose traction and theve hicle
could then skid.
R when visibility is poor
F
F unction of t
unction of t he limit
he limiter
er
The limiter restricts the speed of theve hicle. To
re duce the speed tothe set speed, the limiter
applies the brakes automaticall y.
Yo u can limit the speed as follo ws:
R V
V ar
ar iable:
iable: for a short-term speed restriction,
e.g. in built-up areas
R P
Per
er manent
manent :
:fo r a longer-term speed restric-
tion, e.g. in winter ty remode
Yo u can store any speed abo ve20 km/h up tothe
maximum design speed or up tothe set winter
tyre limit. You can also per form settings while the
ve hicle is stationary if theve hicle has been star-
te d. 200
200
Driving and parking

can be obtained at a
quali/ed specialist work-
shop.
The AS SYST PLUS service inter val display is only
an aid. It is there sponsibility of the driver of the
ve hicle tohave maintenance workcar ried out
more oTen than prescribed due toactual operat-
ing conditions and/or st resses. Batt Batt
er
ery disconnection per
y disconnection per iods
iodsThe AS
SYST PLUS service inter val display can cal-
culate the service due date only when the battery
is connected. #
Display and no tedown the service due date
on the inst rument display before disconnect-
ing the battery (/ page 304). Engine com
Engine com
par
partment
tment Opening and closing t
Opening and closing t
he bonnet
he bonnet &
D
DAN
AN GER
GER Risk of fatal injuries when car ry-
ing out maintenance workduring the
ch arging process
During thech arging process, the high-voltage
on-board electrical system is under high volt-
age. #
Do not per form any main tenance work
during thech arging process. &
W
WARNING
ARNING Risk of accident due todriving
with the bonnet unloc ked
The bonnet may open and blo ckyour vie w. #
Neverre lease the bonnet when driving. #
Before every trip, ensure that the engine
bonnet is loc ked. &
W
WARNING
ARNING Risk of accident and inju ry
when opening and closing the bonnet
The bonnet may suddenly drop into the end
position.
There is a risk of injury for an yone in the
engine bonnet's range of mo vement. #
Do not open or close the bonnet if there
is a person in the bonnet's range of
mo vement. &
W WARNING
ARNING Risk of injury due tooverheated
ve hicle
If yo u open the bonnet in theev ent of an over-
heated vehicle or /re in the engine compart-
ment, thefo llowing situations may occur:
R You may come into contact with hot gases.
R You may come into contact with other
escaping hot operating 0uids. #
Intheev ent of overheating or /re in the
engine compartment, keep the bonnet
closed and call the /re service. Maintenance and care
305
305

*
N
N O
OTE
TE Damage from automatic braking If one of
thefo llowing functions is activated,
th eve hicle brakes automatically in cer tain sit-
uations:
R Active Brake Assist
R Active Distance Assist DISTRONIC
R HOLD function
R Active Parking Assist
To avo id damage totheve hicle, deactivate
th ese systems in thefo llowing or similar situa-
tions: #
During towing. #
In a car wash. *
N
NO OTE
TE Damage due tounsuitable car wash #
Before driving into a car wash make sure
th at the car wash is suitable forth eve hi-
cle dimensions. #
Ensu rethere is su1cient ground clear-
ance between the underbody and the
guide rails of the car wash. #
Ensure that the clearance width of the
car wash, in particular the width of the
guide rails, is su1cient. To
avo id damage toyour vehicle when using a car
wa sh, ensu rethefo llowing beforehand:
R Active Distance Assist DISTRONIC is deactiva-
te d.
R The HOLD function is switched o..
R The 360° Camera or there ve rsing camera is
switched o..
R The side windo wsand sliding sunroof are com-
ple tely closed.
R The blo werfo rth eve ntilation and heating is
switched o..
R The windsc reen wiper switch is in position g.
R The key is at a minimum dis tance of 3 m away
from theve hicle. Otherwise theta ilgate could
open unintentionall y.
R For car washes with a con veyor system: -
Neutral iis engaged.
- Ifyo uwo uld like tolea vetheve hicle while
it is being washed, make sure theke y is
located in theve hicle. The park position
j isotherwise automatically engaged.
% If, aTer the car wash, youre mo vethewax
from the windscreen and wiper rubbers, this
will pr event smearing and reduce wiper noise. Inf
Inf
or
ormation on using a high-pr
mation on using a high-pr essur
essure cleaner
e cleaner &
W
WARNING
ARNING Risk of an accident when using
high-pressure cleaners with round-spr ay
nozzles
The water jet can cause extern ally invisible
damage.
Components damaged in this wa y may un ex-
pectedly fail. #
Do not use a high-pressure cleaner with
round-spr aynozzles. #
Have damaged tyres or chassis parts
re placed immediatel y. Maintenance and ca
re
309 309

R
R
e
ev
v er
er sing camer
sing camer a and 360° Camera
a and 360° Camera
R Open the camera co ver with the multimedia
system (/ page 231).
R Use clean water and a soT clo thtoclean the
camera lens.
R Do not use a high-pressure cleane r.
Tr
Tr ailer hitch
ailer hitch
R Obser vethe no tes on care in the trailer hitch
manufacturer's operator manual.
R Do not clean the ball neck with a high-pres-
sure cleaner or sol vent.
R Remo vetraces of rust on the ball (e.g.using a
wire brush).
R Remo vedirt with a lint-free clo th.
R ATer cleaning, lightly oil or grease the ball
head.
% Before using trailers with anti-torsional cou-
pling, obser vethe manufacturer's operator
manual. N No
ot
tes on car
es on car e of t
e of the int
he int er
erior
ior &
W
WARNING
ARNING Risk of injury from plastic parts
breaking o. aTer the use of sol vent-based
ca re products
Care and cleaning products containing sol-
ve nts can cause sur faces in the cockpit to
become porous. When the airbags are
deplo yed, plastic parts may break away. #
Do not use any care or cleaning products
containing sol vents toclean the cockpit. &
W WARNING
ARNING Risk of injury or fatal injuries
from bleached seat belts
Bleaching or dyeing seat belts can se verely
we aken them.
This can, forex ample, cause seat belts to tear
or fail in an accident. #
Never bleach or dye seat belts. To
avo id damage totheve hicle, obser vethefo l-
lowing no tes on cleaning and care: Seat belts
Seat belts
R Clean with luk ewarmand soapy water.
R Do not use chemical cleaning agents.
R Do not dry byheating them toove r 80°C or
ex posing them todirect sunlight.
Display
Display
R Switch o. the display and let it cool down.
R Clean the sur face carefully with a micro/bre
clo thand a suitable displ aycare product (TFT-
LC D).
R Do not use any other agents.
Head-up displ ay
Head-up display
R Clean with a soT, non-static, lint-free clo th.
R Do not use cleaning agents.
Plas
Plastic tr tic tr im
im
R Clean with a damp micro/bre clo th.
R For heavy soiling: Use a cleaning agent recom-
mended for Mercedes-Benz.
R Do not attach stic kers, /lms or similar materi-
als. Main
tenance and ca re
313
313

&
W
W ARNI NG
ARNI NGRisk of accident when using
tyre sealant
The tyre sealant may be unable toseal the
tyre proper ly, especially in thefo llowing cases:
R there are lar gecuts or punctures in the
tyre (la rger than damage pr eviously men-
tioned)
R the wheel rims ha vebeen damaged
R aTer journe yswith very low tyre pressure
or with 0at tyres #
Do not continue driving. #
Consult a quali/ed specialist workshop. &
W
W ARNING
ARNING Risk of injury and poisoning
from tyre sealant
Ty re sealant is hazardous tohealth and causes
ir rita tion. Do not allow it tocome into contact
with your skin, eyes or clo thing, and do not
swallow it. Do not inhale any vapours. Keep
th e tyre sealant away from children. Obser
vethefo llowing if you come into contact
with the tyre sealant: #
Rinse o. the tyre sealant from your skin
using water immediatel y. #
If tyre sealant gets into your eyes, thor-
oughly rinse them using clean water
immediatel y. #
If tyre sealant has been swallo wed,thor-
oughly rinse out your mouth immediately
and drink plenty of water. Do not induce
vo miting and seek medical attention
immediatel y. #
Change out of clo thing which has come
into contact with tyre sealant immedi-
atel y. #
If an alle rgic reaction occurs, seek medi-
cal attention immediatel y. *
N NO
OTE
TE Overheating due tothe tyre in0ation
compressor running too long #
Do not runth e tyre in0ation compressor
fo r longer than ten minutes without inter-
ru ption. Comply with
the manufacturer's saf ety no tes on
th e stic ker on the tyre in0ation compressor.
Ha ve the tyre sealant bottle replaced in a quali/ed
specialist workshop every /ve years. #
Do not remo veany fore ign objects which ha ve
entered the tyre. #
A1x part 1ofthe TIREFIT stic kerto the
inst rument cluster within the driver's /eld of
vision. #
A1x part 2ofthe TIREFIT stic ker near the
va lve on the wheel with the defective tyre. Breakdown assistance
319 319

#
Tho roughly clean the antifreeze from
component parts before starting the
ve hicle. *
N
NOOTE
TE Damage caused byincor rect cool-
ant #
Only use coolant that has been premixed
with there qu ired antifreeze pr otection.
Information on coolant is available at thefo l-
lowing locations:
R Inthe Mercedes-Benz Speci/cation for
Operating Fluids 320.1
- Athttps://be vo.mercedes-benz.com
- Inthe Mercedes-Benz BeVo App
R Ataqu ali/ed specialist workshop *
N
NOOTE
TE Overheating at high outside temp er-
atures If an inappropriate coolant is used,
the cooling
system is not su1ciently pr otected against
ov erheating and cor rosion at high outside
te mp eratures. #
Only use coolant appr ovedfor
Mercedes-Benz. #
Obser vethe inst ructions in the
Mercedes-Benz Speci/cations for Oper-
ating Fluids 320.1. Ha
ve the coolant regula rly re placed at a quali/ed
specialist workshop.
Proportion of antif reeze concentrate in the engine
cooling system:
R A minimum of 50% (antifreeze pr otection down
to about -37°C)
R A maximum of 55% (antif reeze pr otection
down to-45°C) N
No ot
tes on windscr
es on windscr een w
een washer
asher 0uid
0uid Obser
vethe no tes on operating 0uids
(/ page 352). &
W
WARNING
ARNING Risk of /re and injury from
windscreen washer concent rate
Wi ndsc reen washer concent rate is highly 0am-
mable. If it comes into contact with hot com-
ponents, it may ignite. #
Make sure that windscreen washer con-
cent rate is not spilled near tothe /ller
opening. *
N NOOTE
TE Damage totheex terior lighting due
to unsuitable windscreen washer 0uid Unsuitable windscreen
washer 0uids may
damage the plastic sur face of theex terior
lighting. #
Only use windscreen washer 0uids which
are also suitable for use on plastic sur fa-
ces, e.g. MB SummerFit or MB WinterFit. 354
354
Te
ch nical data