2022 KIA EV6 brakes

Refer to the inside front cover for more information on QR codes.www.youtube.com/KiaFeatureVideos
EV Instrument Cluster Overview Video
EV Distance to Empty (DTE) Video
QR CODES
A POWER (PWR) - Energy consumption rate
B CHARGE (CHG) - Charge status of the regenerative brakes
C Battery State of Charge (SOC) gauge
D Speedometer
E Distance to Empty / Range
F Reduction gear shift indicator
G Odometer
H Regenerative braking level indicator
I EV energy economy
Distance to Empty (DTE) or Range E is the estimated distance an EV can be driven with the remaining electric energy until the battery reaches zero. DTE can vary depending on the selected drive mode, current driving conditions, traffic, driving patterns, air conditioner or heater use, and how much cargo you are carrying.
EV Instrument Cluster Overview
Distance to Empty (DTE) / Range
Your vehicle’s instrument cluster & indicator light locations may differ from those in the illustrations. For more information on the instrument cluster, the LCD Warning Messages and the function of all indicator and warning lights, please refer to section 5 of the Owner ’s Manual.
Illustrations are for demonstration purposes only. Some indicators and warning lights may not appear in illustrations. On the vehicle, they may appear in the LCD.
3*IF EQUIPPEDALWAYS CHECK THE OWNER ’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS.
REMINDERS:
•
If DTE displays “Zero Miles,” you need to charge the vehicle immediately
•
Most electric vehicles can drive an additional t wo to five miles depending on driving conditions
•
Distance to empt y may depend on many factors such as the charge amount of the high voltage bat ter y, weather, temperature, durabilit y of the bat ter y, geographical features, and driving st yle
•Operating the climate control system may reduce the Distance to Empt y
•When decelerating or driving downhill, regenerative braking charges the high voltage bat ter y which minimizes energy loss and increases the Distance to Empt y or Range
•When you set a destination via the on-board navigation system, DTE is calculated based on the route selected. By set ting a final destination, DTE accuracy improves. By knowing the final location, the vehicle can bet ter predict the amount of bat ter y energy it will need to reach that destination
•When operating the climate control, use the DRIVER ONLY function to conser ve energy
•In cold weather, use scheduled heating to reduce the amount of energy consumption
•In the EV Set tings, select WINTER MODE to increase the bat ter y temperature in cold weather
QUICK TIPS
CHG
PWR
EPB
１
00 kWh/ １00m6202 mABS0 20 4060
0mph
0 KMH
268m
268m
96%Lv １READY
P
INSTRUMENT CLUSTERINSTRUMENTCLUSTER
F
HC
D
EAG
B
I

4 *IF EQUIPPEDEV6 FEATURES & FUNCTIONS GUIDE
Indicators & Warning Lights
High Beam Indicator Light
AUTO)JHI
#FBN
"TTJTU
*OEJDBUPS
-JHIU
-PX
#FBN
*OEJDBUPS
-JHIU
-JHIU
0/
*OEJDBUPS
.BTUFS
8BSOJOH
-JHIU
'PS XBSE
4BGFU Z
8BSOJOH
*OEJDBUPS
-BOF
4BGFU Z
*OEJDBUPS
&MFDUSPOJD
#SBLFGPSDF
%JTUSJCVUJPO
&#%

4ZTUFN

8BSOJOH
-JHIUT
5XP
TFQBSBUF
JOEJDBUPST
PO

*OTUSVNFOU
$MVTUFS
MJU
BU
TBNF
UJNF

*NNPCJMJ[FS
*OEJDBUPS

3&"%:
*OEJDBUPS
EC O&$0
.PEF
*OEJDBUPS
SP O RT41035
.PEF
*OEJDBUPS
SNOW4/08
.PEF
*OEJDBUPS
&7
4FS WJDF
8BSOJOH
-JHIU
$IBSHJOH
4ZTUFN
8BSOJOH
-JHIU
4FBU
#FMU
8BSOJOH
-JHIU
-PX
5JSF
1SFTTVSF
-JHIU

5JSF
1SFTTVSF
.POJUPSJOH

4ZTUFN
51.4

.BMGVODUJPO
*OEJDBUPS
&MFDUSPOJD
4UBCJMJU Z
$POUSPM
&4$

*OEJDBUPS

&4$
.BMGVODUJPO
*OEJDBUPS


&MFDUSPOJD
4UBCJMJU Z
$POUSPM
&4$

0''
*OEJDBUPS
1BSLJOH
#SBLF

#SBLF
'MVJE
8BSOJOH
-JHIU
&MFDUSPOJD
1PXFS
4UFFSJOH
&14

8BSOJOH
*OEJDBUPS
"JSCBH
8BSOJOH
-JHIU
"OUJMPDL
#SBLJOH
4ZTUFN
"#4

8BSOJOH
-JHIU
$SVJTF
*OEJDBUPS
AUTOHOLDAUTO HOLD Indicator Light
(red color)
(yellow color)
Regenerative Brake Warning Indicator (Two separate indicators on Instrument Cluster lit at same time)
LED Headlamp Warning Light
Charging Cable Connection Indicator
Power Down Warning Light
High Voltage Bat ter y Low Level Warning Light
12V Bat ter y
EPBElectronic Parking Brake (EPB)
Icy Road Warning Indicator Light*
All-Wheel Drive (AWD) Warning Light*
Highway Lane Change Assist Indicator Light*
Your vehicle’s instrument cluster & indicator light locations may differ from those in the illustrations. For more information on the instrument cluster, the LCD Warning Messages and the function of all indicator and warning lights, please refer to section 5 of the Owner ’s Manual.
This illustration is for demonstration purposes only.
Some indicators and warning lights may not appear in illustration. On the vehicle, they may appear in the LCD.
CHG
PWR
EPB
１
00 kWh/ １00m6202 mABS0 20 4060
0mph
0 KMH
268m
268m
96%Lv １READY
P
A
B
A Distance to Empty / Range
B CHARGE (CHG) - Charge status of the regenerative brakes
INSTRUMENT CLUSTER
INSTRUMENTCLUSTER

5*IF EQUIPPEDALWAYS CHECK THE OWNER ’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS.
Refer to the inside front cover for more information on QR codes.www.youtube.com/KiaFeatureVideos
EV Energy Consumption Video
Tips for Economical Driving Video
QR CODE
Ready indicator light – Illuminates when the vehicle is ready to drive. When the ready indicator light is blinking, a malfunction has occurred. Have an authorized Kia dealer address the concern as soon as possible.
EV Service warning light – Illuminates when there is a malfunction related to the electric vehicle control system. Have an authorized Kia dealer address the concern as soon as possible.
Power down warning light – Illuminates when the vehicle’s speed and per formance are limited for the safety of the electric vehicle.
Charging indicator light – Shows the charging status of the high-voltage battery. When charging, the green indicator turns on. The indicator turns off when not charging.
High-voltage battery low level warning light – Illuminates when the high-voltage battery charge level is insufficient.
Regenerative brake warning lights (when both indicators are lit) –
Illuminates when the regenerative brake system is not functioning correctly.
A State of Charge (SOC) gauge
The State of Charge gauge displays the high-voltage battery charge status.
B Power / Charge Gauge
The Power / Charge gauge provides information on the energy consumption rate of the vehicle and the charge status of the regenerative brakes.
•POWER – Shows the energy consumption rate of the vehicle
when driving uphill or accelerating. The more electric energy used, the higher the gauge level
•CHARGE – Shows the charging status of the battery when it is being charged by the regenerative brakes. The more electric energy charged, the lower the gauge level
C Distance to Empty (DTE)
DTE is the estimated distance the vehicle can be driven with the remaining high-voltage battery level. The DTE will vary according to the selected drive mode and Climate Control settings.
For more information, refer to the Owner ’s Manual.
Energy Consumption
There are several factors that contribute to your electric vehicle’s energy consumption, including maintenance of your vehicle, driving style, weather, durability of the battery and environmental conditions.
Below are tips to help reduce energy consumption:
•Use Scheduled Climate settings to preheat the vehicle before driving
•In EV Settings, select the Winter Mode charge settings
•Keep your vehicle in good condition with regular maintenance
•Don’t “ride” the brake pedal
•Drive at a moderate speed, accelerating smoothly and at a moderate rate
•Use the climate control system less often. Use the Driver Only setting
•Keep tires inflated to the recommended pressure
•Travel lightly, without carrying unnecessary weight in your vehicle
•Ensure wheels are aligned correctly
•Avoid placing large or heavy items on roof racks
•Avoid hilly, winding or poorly maintained roads
For more information, refer to section 1 of the Owner ’s Manual.
Electric Vehicle (EV) Indicators
RE ADY
INSTRUMENT CLUSTERINSTRUMENTCLUSTER

7*IF EQUIPPEDALWAYS CHECK THE OWNER ’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS.
Unplug vehicle to start – When starting the vehicle while the charging connector is still connected, this warning message will appear. Remove the charging connector and then start the vehicle.
Charge Warning Messages on Instrument Panel LCD (Continued)
Unplug vehicle to startCharging Stopped.Check the AC charger
Remaining Time
10 h 18m (90%)
Checkregenerative brakes
Charging Stopped.Check the DC charger
Charging Stopped. Check the AC/DC charger – When there is a problem with the external AC or DC charger, when the AC charger stops charging or when the charging cable is damaged, this message will appear. Check whether there is a problem with the charger or cable. If no problem is found, see an authorized Kia dealer for further assistance.
Remaining Time – Displays the remaining
time to charge the battery to the selected target battery charge level, current SOC and the charge voltage level.
Check Regenerative Brakes – Displays when the
regenerative brake system does not work properly. In this case, have your vehicle inspected by an authorized Kia dealer.
Charging Stopped. Check the cable connector – When the charging connector is not correctly connected to the charging inlet or the charging connector lock release button is pressed, this message will appear. If this occurs, separate the charging connector and re-connect it. Check whether there is any problem (external damage, foreign substances, etc.) with the charging connector and charging inlet. If the problem continues, see an authorized Kia dealer for assistance.
Illustrations are for demonstration purposes only. Some messages may appear differently. See section 1 in the Owner ’s Manual for more information.
REMINDERS:
•
When these warning messages are displayed, do not accelerate or star t the vehicle suddenly
•
All stored driving information (except Odometer and Range) is reset if the bat ter y is disconnected
Charging Stopped.Check the cable connector
Charging Door Open
OPEN
Charging Door Open – When starting the vehicle while the
charging door is still open, this warning message will appear. Close the charging door after charging is complete and then start the vehicle.
30%
INSTRUMENT CLUSTERINSTRUMENTCLUSTER

18*IF EQUIPPEDEV6 FEATURES & FUNCTIONS GUIDE
ELECTRIC VEHICLE (EV) FEATURES
ELECTRIC VEHICLE (EV) F E AT U R E S
Refer to the inside front cover for more information on QR codes.www.youtube.com/KiaFeatureVideos
Regenerative Braking - Paddle Switches, Drive Mode Video
Regenerative Braking - i-Pedal Video
QR CODE
Each of the different Drive Modes allows the regenerative braking level to be set at the driver ’s preference.
QUICK TIP
(Indicator on lower left corner of Instrument display)
Regenerative Braking with Paddle Switches
The regenerative braking system charges the battery when coasting or when you use the brakes to stop the vehicle. Use the paddle switches to adjust the regenerative braking level from 0 to 3 during decelerating or braking. The level will be displayed on the instrument cluster A.
•Pull the left paddle switch B to increase regenerative braking and deceleration
•Pull the right paddle switch C to decrease regenerative braking and deceleration
The paddle shifters do not operate when:
•Both paddle shifters are pulled at the same time
•The vehicle is decelerating by depressing the brake pedal
•Smart Cruise Control (SCC) is active
i-Pedal
i-Pedal driving controls the vehicle speed by the accelerator pedal, both acceleration and deceleration. To activate i-Pedal:
•Pull the left side paddle switch B to Level 3 regenerative braking (see indicator on Instrument Cluster)
•Then pull the left side paddle switch B once again when the regenerative braking level is set to Level 3
The i-Pedal indicator symbol will be illuminated on the instrument cluster.
+
-
96%Lv １READY
+
-
96%Lv １READY
For more information on regenerative braking, i-pedal driving or the Smar t Regeneration System, please refer to section 6 in the Owner ’s Manual.
A
BC
REMINDER: The driver ’s seat belt must be fastened to operate i-pedal driving.
Do not solely rely on i-pedal driving to stop the vehicle, as it may not be able to stop the vehicle depending on vehicle and road conditions. Always use pedal braking when necessar y. Pay at tention to the road condition ahead and apply the brake if necessar y.
+
-
96%Lv １READY
+
-
96%Lv １READY

21†LEGAL DISCL AIMERS ON BACK INSIDE COVER | *IF EQUIPPEDALWAYS CHECK THE OWNER ’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS.
Refer to the inside front cover for more information on QR codes.www.youtube.com/KiaFeatureVideos
Rear Cross-Traffic Collision-Avoidance Assist (RCCA) Video
QR CODERear Cross-Traffic Collision-Avoidance Assist (RCCA)*†4
When engaged, RCCA is a supplemental system. Do not solely rely on this system and always pay at tention to the road and its conditions.
Refer to section 6 in the Owner ’s Manual for more information.
REMINDERS:
•
When vehicle power is cycled, RCCA will remain in the previous state
•
When a vehicle is approaching within the sensing range and coming up faster than 3 mph, the RCCA system will show a warning
RCCA Warning Volume can be adjusted in the Vehicle Set tings on the Infotainment System. Go to Driver Assistance, then Warning Volume.
QUICK TIP
Rear Cross-Traffic Collision-Avoidance Assist (RCCA) is designed to warn the driver under certain conditions. It may activate the Electronic Stability Control (ESC) and temporarily apply braking if it detects cross traffic approaching the vehicle when the vehicle is in reverse.
When the RCCA rear-corner radar sensors detect approaching vehicles from the rear left or rear right side of the vehicle A, RCCA will sound a warning, the warning indicators on the outside rearview mirror will illuminate and a message will appear on the Instrument Cluster LCD B and the Infotainment System screen. If RCCA detects that the collision risk has increased, RCCA automatically applies the brakes to reduce your speed, potentially helping to minimize the effects of a possible collision.
RCCA is designed to operate under the following conditions:
•When the gear shift is in Reverse
•When the vehicle is moving slower than 6 mph
RCCA User Settings:
•To turn RCCA on, press the SETUP key/button on the Infotainment System. Select the VEHICLE button to enter the Vehicle Settings. Select DRIVER ASSISTANCE, PARKING SAFET Y, then REAR CROSS-TR AFFIC SAFET Y
•To set the warning timing, go to the Vehicle Settings, then go to Driver Assistance, then Warning Timing. Select one of the settings:
–
Early/Normal/Standard: Maximizes the amount of distance between the vehicles before the initial warning occurs
– Late: Reduces the amount of distance between the vehicles before the initial warning occurs
•The default Warning Timing is set to Normal. If the Warning Timing is changed, the warning time
of other Driver Assistance systems may also change
ADAS
ADVANCED DRIVER ASSISTANCE SYSTEMS (ADAS)
A
B

Refer to the inside front cover for more information on QR codes.www.youtube.com/KiaFeatureVideos
Forward Collision-Avoidance Assist Video
QR CODE

FCA Warning Volume can be adjusted in the User Set tings in the Instrument Cluster or the Vehicle Set tings* on the audio head unit. Go to Driver Assistance, then Warning Volume.
QUICK TIP
FCA is designed to detect and monitor a vehicle ahead or detect a pedestrian in the roadway through front view camera recognition and front radar signals to warn the driver that a collision is imminent and, if necessary, temporarily apply emergency braking. Initially, FCA provides Forward Collision Warning (FCW) when it detects a potential collision with a vehicle, pedestrian, or cyclist, emitting an audible warning and visual alert on the instrument cluster A.
If the system detects that the collision risk has increased, Forward Collision-Avoidance Assist (FCA) automatically applies the brakes to reduce your speed B, potentially helping to reduce the effects of a possible collision.
On select Kia models, when the driver responds to a potential collision with the Steering Wheel, Evasive Driver Steering Assist C will automatically assist to help prevent the collision. If the driver does not respond, then Evasive Driver Steering Assist may automatically turn the Steering Wheel to avoid the collision.
With the turn signal on, if it detects a potential collision, Junction Turning D may help to avoid the collision with an oncoming vehicle in an adjacent lane when turning left by applying emergency braking.
If it detects a potential collision, Junction Crossing E may help to avoid the collision with oncoming vehicles coming from the left or right side, when crossing an intersection, by applying emergency braking.
If it detects a potential collision, Lane-Change Oncoming F may help to avoid the collision with an oncoming vehicle coming when changing lanes by assisting the driver ’s steering.
If it detects a potential collision, Lane-Change Side G may help to avoid the collision with vehicles ahead when changing lanes by assisting the driver ’s steering.
Forward Collision-Avoidance Assist (FCA)†4
REMINDER: Once the risk factors are not detected, these functions will deactivate, and the driver must steer the vehicle.
ADVANCED DRIVER ASSISTANCE SYSTEMS (ADAS)
ADAS
For illustrative purposes only. Your actual display, but tons and/or features may var y.
26†LEGAL DISCL AIMERS ON BACK INSIDE COVER | *IF EQUIPPEDEV6 FEATURES & FUNCTIONS GUIDE
(Junction Turning)
(Lane Changing – Oncoming Traffic)
(Junction Crossing)
(Lane Changing - Side)(Evasive Steering Assist)
0mph
0 KMH020 4060
202 m１00 kWh/ １00m96%Lv １READY66°F
2 72m
CHG
PWR
Collision Warning
0mph
0 KMH
020 4060
202 m１00 kWh/ １00m96%Lv １READY66°F
2 72m
CHG
PWR
Emergency Braking
0mph
0 KMH
020 4060
202 m１00 kWh/ １00m96%Lv １READY66°F
2 72m
CHG
PWR
Collision Warning
0mph
0 KMH
020 4060
202 m１00 kWh/ １00m96%Lv １READY66°F
2 72m
CHG
PWR
Emergency Braking
A
B
CD
F
E
G

FCA User Settings:
•FCA is ON by default in most Kia models. FCA can be turned ON/OFF by going to the Vehicle Settings in the Infotainment System
•To enable FCA , press the SETUP key/button on the Infotainment System. Select the VEHICLE button to enter the Vehicle Settings. Select DRIVER ASSISTANCE, then FORWARD SAFETY. Then select one of the following modes:
– Active Assist: Vehicle will provide a warning (audible & visual) and may apply the brakes if needed
– Warning Only: Vehicle will provide a warning only (audible & visual)
– Off: System is off, no warnings or braking provided
•To adjust the FCA initial warning activation time, go to User Settings , Driver Assistance, Warning Timing, then select Normal or Late depending on your Kia model:
– Normal: This setting allows for a nominal amount of distance between the vehicles before the initial warning occurs
– Late: Reduces the amount of distance between the vehicles before the initial warning occurs
FCA/FCW will become active when the:
•Ignition is on or the Power button* is ON
•Vehicle is traveling faster than 5 mph
•Electronic Stability Control (ESC) is ON
Forward Collision-Avoidance Assist (FCA)†4 (Continued)
For ward Collision-Avoidance Assist (FCA) is not a substitute for safe driving and may not detect all objects in front of the vehicle. Always drive safely and use caution. Actual User Set tings steps may var y by model. Refer to section 4 in the Owner ’s Manual for more information.
REMINDERS:
•
FCA will be activated by default when the ignition is cycled ON, even when previous set ting was OFF
•
If FCA is operating and the ESC (Electronic Stabilit y Control) is turned off, FCA system is automatically turned off
•
When the FCA system is off, the FCA warning indicator is on in the Instrument Cluster
ADVANCED DRIVER ASSISTANCE SYSTEMS (ADAS)
27†LEGAL DISCL AIMERS ON BACK INSIDE COVER | *IF EQUIPPEDALWAYS CHECK THE OWNER ’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS.
ADAS