2022 HYUNDAI I20 clock

6-115
06
Answering calls
When a call comes in, a notification pop-
up window of the incoming call appears
on the system screen.
To answer the call, press the [1 RPT]
button on the control panel.
• Alternatively, press the Call/Answer
button on the steering wheel.
To reject the call, press the [2 SHFL]
button on the control panel.
• Alternatively, press the Call end
button on the steering wheel.
NOTICE
• Depending on the mobile phone
type, call rejection may not be
supported.
• Once your mobile phone is
connected to the system, the call
sound may be output through the
vehicle’s speakers even after you
exit the vehicle if the phone is within
the connection range. To end the
connection, disconnect the device
from the system or deactivate
Bluetooth on the device.
Using options during a call
During a call, you will see the call screen
shown below. Press a button to perform
the function you want.
To switch the call to your mobile phone,
press the [1 RPT] button on the control
panel.
• Alternatively, press and hold the Call/
Answer button on the steering wheel.
To end the call, press the [2 SHFL] button
on the control panel.
• Alternatively, press the Call end
button on the steering wheel.
Press the [MENU/CLOCK] button on the
control panel to access the following a
menu option:
• Microphone Volume: Adjust the
microphone volume or turn off the
microphone so the other party cannot
hear you.

9-7
09
If your temperature gauge indicates
overheating, you experience a loss of
power, or hear loud pinging or knocking,
the engine may be overheating. If this
happens, you should:
1. Pull off the road and stop as soon as it
is safe to do so.
2. Place the shift lever in N (Neutral,
for Automated manual transmission
vehicle) or neutral (for manual
transmission vehicle) and set the
parking brake. If the air conditioning is
ON, turn it OFF.
3. If engine coolant is running out under
the vehicle or steam is coming out
from the hood, stop the engine. Do
not open the hood until the coolant
has stopped running or the steaming
has stopped. If there is no visible
loss of engine coolant and no steam,
leave the engine running and check
to be sure the engine cooling fan is
operating. If the fan is not running,
turn the engine off.
WARNING
While the engine is running,
keep hands, clothing and
tools away from the moving
parts such as the cooling
fan and drive belt to
prevent serious injury.4. Check for coolant leaking from the
radiator, hoses or under the vehicle. (If
the air conditioning had been in use, it
is normal for cold water to be draining
from it when you stop.)
5. If engine coolant is leaking out,
stop the engine immediately and
we recommend that you call an
authorized HYUNDAI dealer for
assistance.
WARNING
NEVER remove the radiator
cap or the drain plug while
the engine and radiator are
hot. Hot coolant and steam
may blow out under
pressure, causing serious injury.
Turn the engine off and wait until the
engine cools down. Use extreme care
when removing the radiator cap. Wrap
a thick towel around it, and turn it
counterclockwise slowly to the first
stop. Step back while the pressure
is released from the cooling system.
When you are sure all the pressure
has been released, press down on the
cap, using a thick towel, and continue
turning counterclockwise to remove it.
IF THE ENGINE OVERHEATS

9-14
Emergency situations
WARNING
Changing a tire can be dangerous.
Follow the instructions in this section
when changing a tire to reduce the risk
of serious injury or death.
Jack and tools
OBI3080003OBI3080003
 Jack
 Jack handle
 Wheel lug nut wrench
 Towing hook
The jack, jack handle, and wheel lug nut
wrench, towing hook are stored in the
luggage compartment.
The jack is provided for emergency tire
changing only.
Removing and storing the spare
tire
OAI3079005OAI3079005
Turn the winged hold down bolt
counterclockwise to remove the spare
tire.
Store the spare tire in the same
compartment by turning the winged
hold down bolt clockwise.
To prevent the spare tire and tools from
“rattling” store them in their proper
location.
OAI3079006OAI3079006
If it is hard to loosen the tire hold-down
wing bolt by hand, you can loosen it
easily using the wheel lug nut wrench.
1. Put the wrench (1) inside of the tire
hold-down wing bolt.
2. Turn the tire hold-down wing bolt
counterclockwise with the wrench.
IF YOU HAVE A FLAT TIRE

9-15
09
Changing tires
WARNING
A vehicle can slip or roll off of a jack
causing serious injury or death to you
or those nearby. Take the following
safety precautions:
• Do not get under a vehicle that is
supported by a jack.
• NEVER attempt to change a tire in
the lane of traffic. ALWAYS move the
vehicle completely off the road on
level, firm ground away from traffic
before trying to change a tire. If you
cannot find a level, firm place off
the road, call a towing service for
assistance.
• Be sure to use the jack provided with
the vehicle.
• ALWAYS place the jack on the
designated jacking positions on the
vehicle and NEVER on the bumpers
or any other part of the vehicle for
jacking support.
• Do not start or run the engine while
the vehicle is on the jack.
• Do not allow anyone to remain in the
vehicle while it is on the jack.
• Keep children away from the road
and the vehicle.Follow these steps to change your
vehicle’s tire:
1. Park on a level, firm surface.
2. Move the shift lever into N (Neutral,
for Automated manual transmission
vehicle) or neutral (for manual
transmission vehicle), apply the
parking brake, and place the ignition
switch in the LOCK/OFF position.
3. Press the hazard warning flasher
button.
4. Remove the wheel lug nut wrench,
jack, jack handle, and spare tire from
the vehicle.
5. Block both the front and rear of the
tire diagonally opposite of the tire you
are changing.
OBC3080006OBC3080006
6. Loosen the wheel lug nuts
counterclockwise one turn each in
the order shown above, but do not
remove any lug nuts until the tire has
been raised off of the ground.

9-16
Emergency situations
OBC3080007OBC3080007
7. Place the jack at the designated
jacking position under the frame
closest to the tire you are changing.
The jacking positions are plates
welded to the frame with two tabs
and a raised dot. Never jack any other
position or part of the vehicle.
OAI3079010OAI3079010
8. Insert the jack handle into the jack and
turn it clockwise, raising the vehicle
until the tire clears the ground. Make
sure the vehicle is stable on the jack.
9. Loosen the lug nuts with the wheel
lug nut wrench and remove them with
your fingers. Remove the wheel from
the studs and lay it flat on the ground
out of the way. Before removing the
wheel lug nuts, make sure the vehicle
is stable on the jack.10. Install the spare tire onto the studs of
the hub.
11. Tighten the lug nuts with your fingers
onto the studs with the smaller end of
the lug nuts closest to the wheel.
12. Lower the vehicle to the ground
by turning the jack handle
counterclockwise.
OBC3080009OBC3080009
13. Use the wheel lug nut wrench to
tighten the lug nuts in the order
shown. Double-check each lug nut
until they are tight. After changing
tires, we recommend that an
authorized HYUNDAI dealer tighten
the lug nuts to their proper torque as
soon as possible. The wheel lug nut
should be tightened to 11~13 kgf.m
(79~94 lbf.ft).

9-22
Emergency situations
When towing your vehicle in an
emergency without wheel dollies:
1. Place the ignition switch in the ACC
position.
2. Place the shift lever in N (Neutral).
3. Release the parking brake.
NOTICE
Failure to place the shift lever in N
(Neutral) when being towed with the
front wheels on the ground can cause
internal damage to the transmission.
Removable towing hook
OBC3080018OBC3080018
„„5 Door5 Door
1. Open the tailgate/trunk, and remove
the towing hook from the tool case.
2. Remove the hole cover pressing the
lower part of the cover on the front
bumper.
3. Install the towing hook by turning it
clockwise into the hole until it is fully
secured.
4. Remove the towing hook and install
the cover after use.

10-33
10
OBI3090009OBI3090009
„„Petrol Engine (1.0 T-GDi)Petrol Engine (1.0 T-GDi)
OBC3090006OBC3090006
„„Petrol Engine (Smartstream G1.2)Petrol Engine (Smartstream G1.2)
WARNING
Removing radiator cap
• Never attempt to remove the radiator
cap while the engine is operating or
hot. Doing so might lead to cooling
system and engine damage and could
result in serious personal injury from
escaping hot coolant or steam.• Turn the engine off and wait until it
cools down. Use extreme care when
removing the radiator cap. Wrap
a thick towel around it, and turn it
counterclockwise slowly to the first
stop. Step back while the pressure
is released from the cooling system.
When you are sure all the pressure
has been released, press down on the
cap, using a thick towel, and continue
turning counterclockwise to remove
it.
• Even if the engine is not operating,
do not remove the radiator cap
or the drain plug while the engine
and radiator are hot. Hot coolant
and steam may still blow out under
pressure, causing serious injury.
WARNING
The electric motor (cooling
fan) is controlled by engine
coolant temperature,
refrigerant pressure and
vehicle speed. It may
sometimes operate even when the
engine is not running. Use extreme
caution when working near the blades
of the cooling fan so that you are not
injured by a rotating fan blades. As the
engine coolant temperature decreases,
the electric motor will automatically
shut off. This is a normal condition.

10-79
10
Headlight (Low/High) & Position
Light
1. Turn the front wheel at inwards.
OAC3089042TUOAC3089042TU
OAC3089043TUOAC3089043TU
OBC3090055OBC3090055
2. Remove retainers available on under
cover bottom area in the respective
side of headlight for bulb A/S.
3. Remove Wheel guard clips (B),
bumper cover bolt (A) and bumper
upper cover blot (C1) & retainer (C2).
OBC3090038OBC3090038
4. Pushing the Wheel guard aside & pull
front bumper near fender to unlock
front bumper with bumper bracket
near to headlight.
5. Remove the headlight bulb cover by
turning it counter-clockwise from bulb
assembly.
6. Remove the bulb from the headlight
assembly.
7. Install a new headlight bulb and snap
the headlight bulb retaining wire into
position by aligning the wire with the
groove on the bulb.
8. Connect the headlight bulb socket
connector.
9. Install the headlight bulb cover by
turning it clockwise.
10. Install the wheel guard in the reverse
order.