2021 YAMAHA YFM700R Owners Manual

5-8
5
braking performance which could cause an
accident. You could also wear out the brakes
prematurely.
EBU18542Shift pedalThe shift pedal is located on the left side of the en-
gine and is used in combination with the clutch le-
ver when shifting. (See page 7-2.)
EBU18643Reverse knob “REV”The reverse knob is used when shifting into re-
verse. (See page 7-4.)
1. Shift pedal
1
1.
1
UBCX61E0.book Page 8 Friday, January 22, 2021 1:54 PM

5-9
5
EBU37980Fuel tank capRemove the fuel tank cap by turning it counter-
clockwise.
WARNING
EWB02522Gasoline and gasoline vapors are extremely
flammable. To avoid fires and explosions and
to reduce the risk of injury when refueling, fol-
low these instructions. 1. Before refueling, turn off the engine and besure that no one is sitting on the vehicle. Nev-
er refuel while smoking, or while in the vicinity of sparks, open flames, or other sources of
ignition such as the pilot lights of water heat-
ers and clothes dryers.
2. Do not overfill the fuel tank. When refueling, be sure to insert the pump nozzle into the fuel
tank filler hole. Stop filling when the fuel
reaches the bottom of the filler tube. Because
fuel expands when it heats up, heat from the
engine or the sun can cause fuel to spill out of
the fuel tank.1. Fuel tank cap
1
1. Fuel tank filler tube
2. Maximum fuel level
1
2
UBCX61E0.book Page 9 Friday, January 22, 2021 1:54 PM

5-10
5
3. Wipe up any spilled fuel immediately.
NOTICE: Immediately wipe off spilled fuel
with a clean, dry, soft cloth, since fuel may
deteriorate painted surfaces or plastic
parts.
[ECB00982]
4. Turn the fuel tank cap fully clockwise to make sure it is securely closed.EBU38651FuelMake sure there is sufficient gasoline in the tank
before starting off. Refuel if necessary.
WARNING
EWB02532Gasoline is poisonous and can cause injury or
death. Handle gasoline with care. Never siphon
gasoline by mouth. If you should swallow some
gasoline or inhale a lot of gasoline vapor, or get
some gasoline in your eyes, see your doctor
immediately. If gasoline spills on your skin,
wash with soap and water. If gasoline spills on
your clothing, change your clothes.
TIPConfirm the gasoline pump nozzle has the same
fuel identification mark. Recommended fuel:Regular unleaded gasoline (Gasohol [E10]
acceptable)
Fuel tank capacity: 11 L (2.9 US gal, 2.4 Imp.gal)
Fuel reserve amount: 1.6 L (0.42 US gal, 0.35 Imp.gal)1. EN228 fuel identification mark
1
E5
E10
UBCX61E0.book Page 10 Friday, January 22, 2021 1:54 PM

5-11
5About the recommended fuel
This model’s engine has been designed to use
regular unleaded gasoline. The research octane
number should be 91 or higher. If knocking or
pinging occurs, try a gasoline of a different brand
or higher octane.
TIPGasoline containing ethanol can be used if the
ethanol content does not exceed 10% (E10). Gas-
oline containing methanol is not recommended
because it can cause damage to the fuel system
or vehicle performance problems. NOTICEECB00071Use only unleaded gasoline. The use of leaded
gasoline will cause severe damage to internal
engine parts, such as the valves and piston
rings, as well as to the exhaust system.
EBU29892SeatTo remove the seat
Push the seat lock lever backward and pull up the
seat at the rear.1. Seat lock lever
1
UBCX61E0.book Page 11 Friday, January 22, 2021 1:54 PM

5-12
5
To install the seat
Fit the slot in the seat onto the projection on the
fuel tank, insert the projection on the front of the
seat into the seat holder, and then push on the
seat at the rear. Make sure that the seat is securely
fitted.
EBU30055Front shock absorbers The shock absorber spring preload, rebound
damping force, and compression damping force
(fast and slow compression damping) can be ad-
justed.
WARNING
EWB02492
Suspension components become hot during
operation. Never touch the compression
damping force adjusting bolt and screw, the
rebound damping force adjusting screw or
the oil reservoir with your bare hand or skin
until suspension components have cooled.
 Always adjust the shock absorber assem-
blies on the left and right side to the same
setting. Uneven adjustment can cause poor
handling and loss of stability, which could
lead to an accident. Notes on adjusting the suspension
A special wrench can be obtained at a Yamaha
dealer to make the spring preload adjustment.
 When adjusting the damping force settings, turn
the adjuster in direction (a) until it stops, and
then count the turns or clicks in direction (b).
 Although a damping force adjuster may turn or
click beyond the stated minimum settings, such
adjustments are ineffective and may damage
the suspension.
1. Slot
2. Projection
3. Seat holder
1
2
3
2
UBCX61E0.book Page 12 Friday, January 22, 2021 1:54 PM

5-13
5
NOTICEECB00091Never turn an adjusting mechanism beyond
the minimum and maximum settings. Spring preload1. Elevate the vehicle and place a suitable stand under the frame.
2. Loosen the locknut.
3. Turn the spring preload adjusting nut in direc- tion (a) to increase the spring preload and
thereby harden the suspension. Turn in direc-
tion (b) to decrease the spring preload and
thereby soften the suspension.
TIPThe spring preload setting is determined by
measuring distance A, shown in the illustration.
 The shorter distance A is, the greater the spring
preload. The longer distance A is, the lesser the
spring preload.
 Each complete turn of the adjusting nut chang-
es distance A by 1.5 mm (0.06 in). 1. Spring preload adjusting nut
2. Locknut
3. Special wrench
2
1
3
(a)
(b)
UBCX61E0.book Page 13 Friday, January 22, 2021 1:54 PM

5-14
5
4. Tighten the locknut to the specified torque. NOTICE: Always tighten the locknut
against the adjusting nut, and then tighten
it to the specified torque.
[ECB00082]
Rebound damping force
Turn the rebound damping force adjusting screw
in direction (a) to increase the rebound damping
force. Turn in direction (b) to decrease the re-
bound damping force.
Spring preload setting:
Minimum (soft):Distance A = 268.0 mm (10.55 in)
Standard: Distance A = 262.0 mm (10.31 in)
Maximum (hard): Distance A = 253.0 mm (9.96 in)
1. Distance A
1
Tightening torque: Locknut:42 N·m (4.2 kgf·m, 31 lb·ft)1. Rebound damping force adjusting screw
1(a)
(b)
UBCX61E0.book Page 14 Friday, January 22, 2021 1:54 PM

5-15
5Compression damping force
Fast compression damping force
Turn the fast compression damping force adjust-
ing bolt in direction (a) to increase the fast com-
pression damping force. Turn in direction (b) to
decrease the fast compression damping force.Rebound damping force settings:
Minimum (soft):30 click(s) in direction (b)
Standard: 18 click(s) in direction (b)
Maximum (hard): 1 click(s) in direction (b)
1. Fast compression damping force adjusting boltFast compression damping force settings:Minimum (soft):2 turn(s) out from the fully turned in posi-
tion
Standard: 1.5 turn(s) out from the fully turned in po-
sition
Maximum (hard): Adjusting bolt fully turned in
1
(a)
(b) 1
UBCX61E0.book Page 15 Friday, January 22, 2021 1:54 PM