2021 VOLKSWAGEN UP! ESP

•The cooling function of the air conditioning system: if the air conditioning system is set to a very
high or low temperature it will require a lot of energy, which is generated by the engine.
Therefore the temperature setting in the vehicle should not vary too much from the outside
temperature. It may be a good idea to air the vehicle before setting off and then to travel a short
distance with the windows open. The air conditioning system should then be switched on once
the windows have been closed.
•Keep the windows closed when driving at high speeds. Having the windows open increases fuel
consumption.
•Switch the seat heating off as soon as it has served its purpose.
•Switch the rear window heating off as soon as the window has defogged and is clear of ice.
Other factors that increase fuel consumption (examples):
•Fault in engine management.
•Driving in hilly regions.
Driving in a fuel-efficient manner
Fig. 102 Fuel consumption in litres per 100 km at two different outside temperatures
First read and observe the introductoryinformation and safety warnings⇒
Introduction
By adopting an economical driving style and anticipating the traffic situation ahead, you can easily
reduce fuel consumption by 10-15 %.
Cars use most fuel when accelerating. If you think ahead when driving, you will need to brake less
and thus accelerate less. Wherever possible, let the car roll slowly to a stop, for instance when you
can see that the next traffic lights are red.
Avoid short journeys
Directly after a cold start, the engine has a very high fuel consumption. The engine reaches its
working temperature after a few kilometres, when fuel consumption will return to a normal level.
The engine and catalytic converter need to reach their proper working temperature in order to
minimise fuel consumption and emissions. The outside temperature is a key factor.
The different rates of fuel consumption for the same distance at both +20°C (+68°F) and at -
10°C (+14°F) are shown in ⇒ Fig. 102.
Therefore, avoid making too many short journeys and car share whenever possible.
Under the same conditions, the vehicle will use more fuel in winter than in summer.
Not only is it illegal in some countries to warm up the cold engine by running it while the vehicle is
stationary, it is also technically unnecessary and a waste of fuel.
Adjust the tyre pressure
The correct tyre pressure reduces rolling resistance and therefore also fuel consumption.
Ensure that any new tyres purchased have optimum rolling resistance.
Using low viscosity engine oils
Fully synthetic low viscosity engine oils reduce fuel consumption. Low viscosity engine oils
decrease frictional resistance in the engine and spread better and more quickly, especially for cold
starts. They are especially effective in vehicles that make a lot of short journeys.
Always ensure that the engine oil level is correct and that you keep to the service intervals (oil
change intervals).
When buying engine oil, always ensure that it complies with engine oil norms and has been
approved by Volkswagen.

Avoid unnecessary loads
The lighter the vehicle, the more economical and environmentally-friendly it is. An extra weight of
100 kg can increase fuel consumption by up to 0.3 l/100 km.
Remove all unnecessary objects and loads from the vehicle.
Remove any unnecessary special equipment and accessories
The more aerodynamic a vehicle, the lower its fuel consumption. Special equipment and
accessories, such as roof carriers or bicycle carriers, make the vehicle less aerodynamic.
You should therefore remove any special equipment and luggage carriers that are not in use,
especially if you are going to be driving at high speeds.
Steering
 Introduction
This chapter contains information on the followingsubjects:
⇒ Warning and indicator lamps
⇒ Information on steering
Depending on its equipment level the vehicle may have power steering.
The power steering is not hydraulic. It is an electromechanical system. The advantage of this
steering system is that no hydraulic hoses, hydraulic oil, pumps, filter or other parts are required.
The electromechanical system reduces fuel consumption. A hydraulic system requires constant oil
pressure in the system, whereas an electromechanical steering system only needs an energy
supply while steering.
The power steering provided by the electromechanical steering system automatically adjusts to the
vehicle speed, steering wheel torque and steering wheel angle. The electromechanical steering
only functions when the engine is running.
Additional information and warnings:
•Starting and stopping the engine ⇒ Starting and stopping the engine
•Battery ⇒ Vehicle battery
•Tow-starting and towing ⇒ Tow-starting and towing
Warning and indicator lamps
First read and observe the introductoryinformation and safety warnings⇒
Introduction
Lit upPossible causeSolution
The electromechanical steering is faulty
or not working.
The steering should be checked by a
qualified workshop as soon as possible.
Electromechanical steering function
reduced.
The steering should be checked by a
qualified workshop as soon as possible.
If the yellow warning lamp remains off after
the ignition has been restarted and you have
driven a short distance, you do not need to
consult a qualified workshop.
The vehicle battery has been
disconnected and reconnected.
Drive a short distance at a speed of
15 – 20 km/h (9 – 12 mph).
Several warning and indicator lamps will light up briefly as a functional check when the ignition is
switched on. They will go out soon afterwards.
If the power steering is not working, the steering wheel is difficult to turn, which makes it
difficult to steer the vehicle.
•The power steering only functions when the engine is running.
•Never allow the vehicle to roll if the engine is switched off.
•Never remove the vehicle key from the ignition lock when the vehicle is in motion. The
steering lock may be activated and you will no longer be able to steer the vehicle.
WARNING

Indicator lamps
First read and observe the introductoryinformation and safety warnings⇒
Introduction
Lit upPossible causeSolution
The start/stop system is not available.
Automatic engine stop active.
The start/stop system is available, but an
automatic engine stop is not possible.
Check whether all technical requirements
have been fulfilled. If not, remedy any
shortfalls ⇒ Start/stop system.
Start/stop system cannot start the engine.
Start the engine again manually using the
vehicle key ⇒ Starting and stopping the
engine.
Fault in the alternator.⇒ Vehicle battery
FlashesPossible causeSolution
Start/stop system not available.Proceed to a qualified workshop.
Several warning and indicator lamps will light up briefly as a functional check when the ignition is
switched on. They will switch off after a few seconds.
Start/stop system
Fig. 103 In the upper part of the centre console: button for the start/stop system
First read and observe the introductoryinformation and safety warnings⇒
Introduction
When the start/stop system is active, the engine is switched off whenever the vehicle is stationary.
The engine then restarts automatically as soon as it is required.
The function is automatically activated every time the ignition is switched on. The instrument cluster
display shows information about the current status ⇒ Indicator lamps.
Always switch off the start/stop system manually when driving through water.
Vehicles with a manual gearbox
•When the vehicle is stationary, disengage the gear and release the clutch pedal. The engine is
stopped.
The intelligent technology of the pull-away assist systems cannot overcome the laws of
physics. Never let the extra convenience afforded by pull-away assist systems tempt you into
taking any risks when driving – this can cause accidents.
•Unintentional vehicle movements can cause serious injury.
•The pull-away assist systems cannot replace the full concentration of the driver.
•Always adapt your speed and driving style to suit visibility, weather, road and traffic
conditions.
•A pull-away assist system cannot hold the vehicle in all hill start situations or brake it
sufficiently on all slopes going downhill (e.g. if the ground is slippery or icy).
WARNING
Failure to observe the warning lamps could lead to your vehicle breaking down in traffic, and
to accidents and serious injuries.
•Never ignore any warning lamps that are lit up.
•Stop the vehicle as soon as it is possible and safe to do so.
WARNING
Failure to observe the illuminated indicator lamps could lead to the vehicle being damaged.
NOTICE

•Depress the clutch pedal to restart the engine.
Important preconditions for automatic engine switch-off
•The driver is wearing their seat belt.
•The driver door is closed.
•The bonnet is closed.
•A minimum engine temperature has been reached.
•The vehicle has been moved since the engine was last switched off.
•The defrost function of the air conditioning system is not switched on.
•The charging state of the vehicle battery is sufficient.
•The temperature of the vehicle battery is not too low or too high.
•The vehicle is not on a steep incline.
•Reverse gear is not engaged.
Conditions for an automatic restart
The engine can start automatically under the following conditions:
•If the vehicle rolls on.
•If the voltage of the vehicle battery falls.
Conditions that make a key start necessary
The engine has to be started manually with the vehicle key in the following conditions:
•If the driver unfastens their seat belt.
•If the driver door is opened.
•If the bonnet is opened.
Switching the start/stop system on and off
•Press the button in the centre console ⇒ Fig. 103.
•If start/stop system has been deactivated, the indicator lamp in the button lights up.
If the start/stop system has switched the engine off, the engine will start again as soon as the
system has been switched off manually with the button.
In some cases, it will be necessary to restart the engine manually with the vehicle key. Take
note of the corresponding indicator lamp in the instrument cluster.
Hill Hold Assist
First read and observe the introductoryinformation and safety warnings⇒
Introduction
The Hill Hold Assist function actively holds the vehicle when pulling away on an incline.
The Hill Hold Assist function is automatically activated if the following
conditions are met
Points 1 to 3 must be fulfilled at the same time:
Manual gearboxAutomated manual gearbox
1.On an incline, the stationary vehicle must be held in position with the footbrake until the
vehicle starts moving.
2.The engine is running smoothly.
3.
Fully depress the clutch pedal and move the
gear stick to the 1st gear position if you want
to drive forwards up a hill or to the R position
if you want to reverse up a hill.
Position D is selected when driving forwards
up an incline or position R is selected for
driving in reverse up an incline.
The brake servo and the electromechanical steering will not function if the engine is switched
off.
•Never allow the vehicle to roll if the engine is switched off.
•The start/stop system must be switched off if work is to be carried out in the engine
compartment.
WARNING
If the start/stop system is used in very high outside temperatures over a long period, the
vehicle battery can be damaged.
NOTICE

FunctionWhat to do when the ignition is switched on
Switching the display
off manually
If applicable, press the portable navigation unit screen (delivered by
Volkswagen)
Switching off the
ParkPilot
automatically:
After shifting out of reverse gear.
Things to note about ParkPilot
•In some cases, the ParkPilot registers water and ice on the ultrasound sensors as an obstacle.
•The acoustic signal will become quieter after a few seconds if the distance remains the same.
The volume will remain constant if the acoustic warning is continuous.
•As soon as the vehicle moves away from the obstacle again, the intermittent acoustic warning is
switched off automatically. If the vehicle approaches the obstacle again, the acoustic warning is
switched on automatically.
•A Volkswagen dealership can adjust the volume of the acoustic signals.
If there is a function fault in the ParkPilot, an acoustic warning is emitted for approximately 3
seconds when switched on for the first time. The ParkPilot should be immediately checked by a
qualified workshop.
Acoustic and optical ParkPilot signals at the rear of the vehicle
Fig. 105 ParkPilot screen display on portable navigation unit (delivered by Volkswagen)
First read and observe the introductoryinformation and safety warnings⇒
Introduction
Key
⇒ Fig. 105Meaning
ⒶScanned area behind the vehicle.
Yellow segment depicts an obstacle.
Red segment depicts an obstacle located close to the vehicle.
Depending on equipment level the areas to the rear of the vehicle that are scanned by the
ultrasound sensors are shown in the display of the portable navigation system (delivered by
Volkswagen). The positions of potential obstacles are displayed relative to the vehicle ⇒.
Acoustic signals and screen
Acoustic signals are given when the vehicle approaches an obstacle located to the rear. An
intermittent acoustic warning is given if there is sufficient distance between the vehicle and an
obstacle. The shorter the distance, the shorter the intervals. The acoustic warning will sound
continuously if the obstacle is very close.
If you continue to drive the vehicle closer to the obstacle despite the continuous acoustic warning,
the system will no longer be able to measure the distance.
Depending on the vehilcle equipment level, the scanned areas are displayed as several segments
in a display ⇒ Fig. 105. The closer the vehicle drives towards an obstacle, the closer the segment
will move to the vehicle in the display. The collision area has been reached when the penultimate
segment is displayed, if not before. Do not drive on!
Area of the vehicleDistance of the
vehicle from an
obstacle
Acoustic
signal
segment colour
when obstacle is
detected
Ⓐ
Rear centreapprox. 31 – 150 cmIntermittent
toneYellow
Rear sideapprox. 31 – 60 cm
Obstacle close
to the vehicleapprox. 0 – 30 cmConstant
toneRed
Do not allow the images shown on the screen to distract you from the traffic around you.
WARNING

If, in a potential collision scenario, the city emergency brake function detects that the driver is
applying the brakes with insufficient pressure, the system can increase the brake pressure in order
to reduce speed ahead of the collision. Hence the system can help minimise the consequences of
an accident.
Additional information and warnings:
•Exterior views ⇒ Exterior views
•Lower section of the centre console ⇒ Overview of the centre console
•Instrument cluster ⇒ Instrument cluster
•Accessories, modifications, repairs and renewal of parts ⇒ Accessories, modifications, repairs
and renewal of parts
The brake pedal travel decreases when the city emergency brake function is triggered. This
may make the brake pedal feel stiffer.
Automatic brake intervention by the city emergency brake function can be stopped by using
the clutch, the accelerator or steering intervention.
Unusual noises may be heard if the city emergency brake function is applying an automatic
braking procedure. This is normal and the noises are caused by the braking system.
Warning and indicator lamps
First read and observe the introductoryinformation and safety warnings⇒
Introduction
The city emergency brake function is switched on every time the ignition is switched on. No display
will be shown to alert you of this.
The indicator lamp will be lit up if the city emergency brake function is switched off, is working or if
there is a fault in the system.
Lit upPossible cause ⇒Solution
The city emergency brake function
was switched on using the button
⇒ Fig. 109.
The indicator lamp is switched off
automatically after approximately 5
seconds.
FlashesPossible cause ⇒Solution
Quickly: city emergency brake function
is braking automatically or has braked
automatically.
Indicator lamp will go out automatically.
Slowly: city emergency brake function
currently not available.
While the vehicle is stationary, switch off
the engine and re-start it again. If
necessary, inspect the laser sensor (for
The intelligent technology of the city emergency brake function cannot change the laws of
physics or the system-related vehicle limitations. Never let the extra convenience afforded by
the city emergency brake function tempt you into taking any risks when driving. The driver is
always responsible for braking in time.
•The city emergency brake function cannot prevent accidents and serious injuries by itself.
•The city emergency brake function can carry out unwanted brake interventions in certain
complex situations, e.g. if a vehicle cuts very closely in front of you.
WARNING
Incorporating the city emergency brake function into your own driving style can cause
accidents and serious injuries. The system is not a substitute for the full concentration of the
driver.
•Adapt your speed and distance from the vehicles ahead to suit visibility, weather, road and
traffic conditions.
•The city emergency brake function does not react to persons, animals and vehicles
crossing or approaching in the same lane.
•Brake the vehicle by depressing the brake if the vehicle rolls forwards once the city
emergency brake function has been applied.
WARNING
Switch off the city emergency brake function if you suspect that the laser sensor has been
damaged. This can help to prevent further damage.
•Repairs to the laser sensor require specialist knowledge. Volkswagen recommends using
a Volkswagen dealership for this purpose.
NOTICE

FlashesPossible cause ⇒Solution
soiling, ice, roof load protruding over the
front) ⇒. Proceed to a qualified
workshop immediately and have the
system checked if it is constantly
unavailable.
When travelling between
5 – 30 km/h (3 – 19 mph): the city
emergency brake function was
switched off using the button
⇒ Fig. 109.
Switch on the city emergency brake
function using the button
⇒ Fig. 109.
Several warning and indicator lamps will light up briefly as a functional check when the ignition is
switched on. They will switch off after a few seconds.
Laser sensor
Fig. 107 On the windscreen: laser sensor for the city emergency brake function
Fig. 108 Detection range of the laser sensor
First read and observe the introductoryinformation and safety warnings⇒
Introduction
The system monitors the traffic in front of the vehicle using a laser sensor in the windscreen
⇒ Fig. 107.
Vehicles travelling ahead can thus be recognised up to a distance of approximately 10 m.
Failure to observe the warning lamps could lead to your vehicle breaking down in traffic, and
to accidents and serious injuries.
•Never ignore any warning lamps that are lit up.
•Stop the vehicle as soon as possible and when safe to do so.
WARNING
Failure to observe the illuminated indicator lamps could lead to the vehicle being damaged.
NOTICE

•Preparation for working in the engine compartment ⇒ Preparation for working in the engine
compartment
Fuels can pollute the environment. Any spilt service fluids must be cleaned up and disposed
of properly.
Indicator lamps and fuel gauge
Filling the tank incorrectly and incorrect handling of fuel can cause explosions, fire and
serious burns and injuries.
•Always ensure that the tank cap is properly closed, to prevent the evaporation and spillage
of fuel.
•Fuel is highly explosive and inflammable and can cause serious burns and other injuries.
•Fuel can spill out if the engine is not switched off or the filler nozzle is not fully inserted
into the fuel filler neck when filling the tank. This can cause fires, explosions and serious
burns and injuries.
•When filling the tank with fuel, the engine and the ignition must be switched off for safety
reasons.
•When filling the tank, always switch off your mobile telephone and two-way radio or any
other radio equipment. Electromagnetic radiation can generate sparks which can in turn
start a fire.
•Never get back into the vehicle while filling the tank. If in exceptional cases you have to
enter the vehicle, close the door and touch a metal object before touching the filler nozzle
again. This will remove any electrostatic charge from you. Failure to do so could generate
a spark. Sparks can cause a fire when filling the tank.
•Never fill the tank or fill up a spare canister near open flames, sparks or glowing matter
(e.g. cigarettes).
•Electrostatic discharge and electromagnetic radiation must be avoided when filling the
tank.
•Follow all applicable safety information provided by the filling station when filling the tank.
•Never spill fuel in the vehicle or in the luggage compartment.
WARNING
For safety reasons, Volkswagen does not recommend carrying a spare fuel canister in the
vehicle. Fuel can spill out of the full or empty canister and catch fire, especially in the event of
an accident. This could cause explosions, fire and injuries.
•If, in exceptional circumstances, you have to transport a spare fuel canister, please note
the following:
- When refilling never place the canister in or on top of the vehicle, for example in the
luggage compartment. There may be an electrostatic charge during refilling causing
the fuel fumes to ignite.
- Always place the spare fuel canister on the ground.
- When filling a spare fuel canister, place the filler nozzle as far as possible into the
filler opening.
- If the spare fuel canister is made of metal, the filler nozzle must have constant
contact with the canister in order to avoid static charging.
- Please follow all legislation concerning the use, stowage and transport of a spare
fuel canister.
- Ensure that the spare fuel canister is accordance with the industry standard, such
as ANSI or ASTM F852-86.
WARNING
•Remove spilt fuel from all vehicle components as quickly as possible in order to avoid
damage to the wheel housing, tyres and vehicle paint.
•Filling the tank with diesel in a vehicle with a petrol engine can cause serious and
expensive engine damage and cause damage to the fuel system that is not covered by any
Volkswagen guarantee. Do not start the engine under any circumstances if you have
refilled using the incorrect fuel. Seek expert assistance. The substances in these fuels can
cause serious damage to the fuel system and to the engine itself if it is switched on.
NOTICE