2021 TOYOTA RAV4 PHEV cover

5447-3. Do-it-yourself maintenance
nal facing up.
4 When installing, reverse the
steps listed.
WARNING
■Battery precautions
Observe the following precautions.
Failure to do so may result in death or
serious injury.
●Do not swallow the battery. Doing
so may cause chemical burns.
●A coin battery or button battery is
used in the electronic key. If a bat -
tery is swallowed, it may cause severe chemical burns in as little as
2 hours and may result in death or
serious injury.
●Keep away new and removed bat -
teries from children.
●If the cover cannot be firmly closed,
stop using the electronic key and stow the key in t he place where
children cannot reach, and then
contact any auth orized Toyota retailer or Toyota authorized
repairer, or any reliable repairer as
soon as possible.
●If you accidentally swallow a battery
or put a battery into a part of your body, get emergency medical atten -
tion immediately.
■To prevent battery explosion or leakage of flammable liquid or
gas
●Replace the batt ery with a new bat- tery of the same type. If a wrong
type of battery i s used, it may
explode.
●Do not expose batteries to
extremely low pressure due to high altitude or extremely high tempera -
tures.
●Do not burn, break or cut a battery.
■Certification for the electronic key battery
CAUTION
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT
TYPE.
DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUC -
TIONS
NOTICE
■When replacing the battery
Use a flathead screwdriver of appro - priate size. Applying excessive force
may deform or damage the cover.
■For normal operation after
replacing the battery
Observe the following precautions to prevent accidents:
●Always work with dry hands.
Moisture may cause the battery to rust.
●Do not touch or move any other component inside the remote con -
trol.
●Do not bend either of the battery
terminals.

545
7
7-3. Do-it-yours elf maintenance
Maintenance and care
1Turn the power switch off.
Confirm that the charging connector is
not connected. Also, do not use the
Remote Air Conditioning System during the procedure.
2 Open the fuse box cover.
Engine compartment: Type A
fuse box
Push claw and to completely
release the lock, and then lift up the
cover.
Engine compartment: Type B
fuse box
Push claw and to completely
release the lock, and then lift up the
cover.
Left side instrument panel
Left-hand drive vehi cles: Remove the
lid.
Right-hand drive vehicles: Push the tab
in and remove the cover, and then
remove the lid.
Checking and replacing
fuses
If any of the electrical compo -
nents do not operate, a fuse
may have blown. If this hap -
pens, check and replace the
fuses as necessary.
Checking and replacing
fuses
AB
AB

5467-3. Do-it-yourself maintenance
Right side luggage compartment
Open the deck board. (→P.472)
Push claw and to completely
release the lock, and then lift up the
cover.
3 Remove the fuse.
Only type A fuse can be removed using
the pullout tool.
4 Check if the fuse is blown.
Replace the blown fuse with a new fuse
of an appropriate amperage rating. The
amperage rating can be found on the fuse box lid.
Type A
Normal fuse
Blown fuse
Type B
Normal fuse
Blown fuse
AB
A
B
A
B

547
7
7-3. Do-it-yours elf maintenance
Maintenance and care
Type C
Normal fuse
Blown fuse
■After a fuse is replaced
●When installing the lid, make sure that
the tab is installed securely.
●If the lights do not t urn on even after
the fuse has been replaced, a bulb
may need replacement. ( →P.548)
●If the replaced fuse blows again, have
the vehicle inspec ted by any autho-
rized Toyota retailer or Toyota autho - rized repairer, or any reliable repairer.
■If there is an over load in a circuit
The fuses are designed to blow, protect -
ing the wiring har ness from damage.
■When replacing an electronic com- ponent, such as a lights, etc.
Toyota recommends that you use genu -
ine Toyota product s designed for this vehicle. Because certain bulbs are con -
nected to circuits de signed to prevent
overload, non-genuine parts or parts not designed for this vehicle may be unus -
able.
A
B
WARNING
■To prevent system breakdowns
and vehicle fire
Observe the following precautions. Failure to do so may cause damage
to the vehicle, and possibly a fire or
injury.
●Never use a fu se of a higher
amperage rating than that indi -
cated, or use any other object in
place of a fuse.
●Always use a genuine Toyota fuse
or equivalent. Never replace a fuse with a wire,
even as a temporary fix.
●Do not modify the fuses or fuse
boxes.
NOTICE
■Before replacing fuses
Have the cause of el ectrical overload
determined and repaired by any authorized Toyota retailer or Toyota
authorized repairer, or any reliable
repairer as soon as possible.
■To prevent damage to the engine
compartment fuse box cover
When opening the fuse box, com - pletely release th e claw locks before
lifting up the cover. Otherwise, the
claws may be damaged.

551
7
7-3. Do-it-yours elf maintenance
Maintenance and care
8Reinstall the fender liner.
9 Reinstall the screws.
■Rear turn signal lights
1 Open the back door and remove
the cover.
2 Remove the screws and remove
the light unit.
Remove the light unit by pulling it
directly backward from the rear of the vehicle.
3 Turn the bulb base counter-
clockwise.
4 Remove the light bulb.
5 Install a new light bulb then
install the bulb base to the light

5527-3. Do-it-yourself maintenance
unit by inserting it and turning
the bulb base clockwise.
6 Align the grooves on the light
unit with the claws, and insert
the light unit straight so that the
pin on the light unit fit into the
hole.
Confirm that the light unit is completely secured.
7 Reinstall the screws.
8 Reinstall the cover.
■Back-up lights
1 Open the back door and remove
the cover.
To prevent damage to the cover, pro - tect the tip of the screwdriver with a rag.
2 Turn the bulb base counter-
clockwise.
Remove the cord fr om the clip before

553
7
7-3. Do-it-yours elf maintenance
Maintenance and care
turning the bulb base.
3Remove the light bulb.
4 Install a new light bulb.
5 Install the bulb base to the light
unit by inserting it and turning
the bulb base clockwise.
Secure the cord with the clip back again
after installing the bulb base.
6Reinstall the cover.
■Outer foot lights (if equipped)
1 Press the upper part of the out-
side rear view mirror to tilt the
mirror face upward, and discon -
nect the four tabs behind the
mirror.
Pry the mirror out toward you, and dis -
connect two tabs at a time.
Work carefully, ensuring that you do not

5547-3. Do-it-yourself maintenance
drop the mirror.
2 Disconnect the connectors
behind the mirror, and remove
the mirror.
Make sure to check the connectors, to
avoid connecting upside down when reinstalling.
Work carefully, ensuring that you do not
drop the mirror.
3 Disconnect the tabs behind the
mirror cover, and remove the
mirror cover.
4 Fold the mirror before removing
the light unit.
5 Remove the light unit.
Remove the two screws, and disen-
gage the two tabs with a flat-head screwdriver.
Work carefully, ensuring that you do not