2021 SUZUKI IGNIS temperature

75RM4-01E
Vehicle Data RecordingsThere are certain components of your vehicle (the “Vehicle”) incorporating data storage modules or memories, which temporarily or per-
manently store the technical data below listed. These data are exclusively technical and serve for (i) identifying and correcting faults
occurred in the Vehicle and/or ( ii) optimizing functions of the Vehicle.Recorded data (the “Recorded Data”)• Malfunctions, faults, and erro rs in important system component s. (e.g. lights, brakes)
• Reactions of the Vehicle in cer tain situations (e.g. inflation of SRS air bags, activation of stability control system).
• Operating conditions of system components (e.g. filling levels).
• Status messages of the Vehicle and its individual components ( e.g. vehicle speed, acceleration, deceleration, lateral acceleration).
• Ambient conditions (e.g. outside temperature).
Recorded data vary depending on vehicle model or grade.

2-2
BEFORE DRIVING
75RM4-01E
For vehicles with a keyless push start
system
If this light blinks, change the ignition mode
to LOCK (OFF), and then change it back to
ON. Also refer to “If the master warning
indicator light blinks and the engine cannot
be started” in “Starting engine (vehicle with
keyless push start system)” in the “OPER-
ATING YOUR VEHICLE” section.
If the light still blinks after the ignition mode
is changed back to ON, there may be
something wrong with your key or with the
immobilizer system. Ask your SUZUKI
dealer to have the system inspected.
The immobilizer/keyless push start system
warning light may also blinks if the remote
controller is not in the vehicle when you
close the door or attempt to start the
engine.
NOTE:
• If you lose your immobilizer ignition key or remote controller, ask your SUZUKI
dealer as soon as possible to deactivate
the lost one, and to make a new key or
remote controller.
• If you own other v ehicles with immobi-
lizer keys, keep those keys away from
the ignition switch or the engine switch
when using your SUZUKI vehicle. Other-
wise, or the engine may not be started
because they may interfere with your
SUZUKI vehicle’s immobilizer system. • If you attach any metal objects to the
immobilizer key or remote controller, it
may not start the engine.
Ignition key reminderA buzzer sounds intermittently to remind
you to remove the ignition key if it is in the
ignition switch when the driver’s door is
opened.
Door locksSide door locks
60B008
(1) LOCK
(2) UNLOCK
(3) Rear
(4) Front
To lock a driver’s door from the outside of
the vehicle:
• Insert a key and turn the top of the key toward the front o f the vehicle, or
• Turn the lock knob forward, then pull and
hold the door handle as you close the
door.
NOTICE
The immobilizer key and remote con-
troller are sensitive electronic instru-
ments. To avoid damaging them:
• Do not expose them to impacts,moisture or high temperature such
as on the dashboard under direct
sunlight.
• Keep them away from magnetic
objects.
(2)
(1) (3)
(4)
EXAMPLE

2-10
BEFORE DRIVING
75RM4-01E
80J056
(1) 80 cm (2 1/2 feet)
When the remote controller is within
approximately 80 cm (2 1/2 feet) from a
front door handle or the tailgate switch, you
can lock or unlock the doors by pushing
the request switch.
NOTE:
• If the remote controller is outside the request switch operating range
described above, you will not be able to
operate the request switch.
• If the battery of th e remote controller
runs down or there are strong radio
waves or noise, the request switch oper-
ating range may be reduced or the
remote controller may be inoperative.
• If the remote controller is too close to the door glass, the request switches may not
operate. • If a spare remote controller is in the vehi-
cle, the request switches may not oper-
ate normally.
• The remote controller will only operate a request switch if it is within the switch’s
operating range. For example, if the
remote controller is within the operating
range of the driver’s door request switch
but not the front passenger’s door
request switch or the tailgate request
switch, the driver’s door switch can be
operated but the front passenger’s door
switch or tailgate switch cannot be oper-
ated.
NOTE:
The keyless push start system may not
function correctly in certain environments
or under certain operating conditions such
as the following:
• When there are strong signals coming from a television, power station or a cel-
lular phone. • When the remote controller is in contact
with or covered by a metal object.
• When a radio wave type remote keyless
entry is used nearby.
• When the remote controller is placed near an electronic device such as per-
sonal computer.
Some additional precautions you should
take and information you should be aware
of are:
• Check that the key is stowed in the remote controller. If the remote controller
becomes unreliable, you will not be able
to lock or unlock the doors.
• Check that the driver always carries the
remote controller.
• If you lose one of the remote controllers,
ask your SUZUKI dealer as soon as pos-
sible for a replacement. Have your
dealer program the new remote control-
ler code in your vehicle’s memory so that
the old code is erased.
• You can use up to four remote control-
lers and the keys for your vehicle. Ask
your SUZUKI dealer for details.
• The battery life of the remote controller
is about two years, but it can vary
depending on usage conditions.
(1)
(1)
(1)
EXAMPLE
NOTICE
The remote controller is a sensitive
electronic instrument. To avoid dam-
aging the remo te controller:
• Do not expose it to impacts, mois- ture or high temperature such as
by leaving it on the dashboard
under direct sunlight.
• Keep the remote controller away
from magnetic objects such as a
television.

2-14
BEFORE DRIVING
75RM4-01E
Central door locking system
• To lock all doors, push LOCK button (1)once.
• To unlock only the driver’s door, push UNLOCK button (2) once.
• To unlock other doors, push UNLOCK
button (2) once again.
NOTE:
You can switch the fu nction that unlocks all
doors from requiring two pushes to requir-
ing one push, and vice versa, via the infor-
mation display setting mode. For details on
how to use the informati on display, refer to
“Information display” in this section.
Central door locking system with the
dead lock system (if equipped)
If you want to prevent tamper-unlocking of
the door locks, use this method. When the
dead lock system is activated, operating
the lock knobs will not unlock the side
doors.
To activate this system:
To lock all doors, push LOCK button (1)
twice within 3 seconds.
To release this system:
• To unlock only the driver’s door, push UNLOCK button (2) once.
• To unlock other doors, push UNLOCK
button (2) once again. NOTE:
You can switch the fu
nction that unlocks all
doors from requiring two pushes to requir-
ing one push, and vice versa, via the infor-
mation display setting mode. For details on
how to use the informati on display, refer to
“Information display” in this section.
The turn signal lights will flash once when
the doors are locked and then the turn sig-
nal lights will flash once again when the
doors are locked with the dead lock sys-
tem.
When the doors are unlocked:
• The turn signal lights will flash twice.
• If the interior light switch is in DOOR position, the interior light will turn on for
about 15 seconds and then fade out. If
you insert the key into the ignition switch
during this time, the light will start to fade
out immediately.
Check that the doors are locked after you
operate LOCK button (1).
NOTE:
If no door is opened within about 30 sec-
onds after UNLOCK button (2) is operated,
the doors will automatically lock again. NOTE:
• The maximum operating distance of the
keyless entry system transmitter is about
5 m (16 ft.), but this can vary depending
on the surroundings, especially near
other transmitting devices such as radio
towers or CB (Citizen’s Band) radios.
• The door locks cannot be operated with the transmitter, if the ignition key is
inserted in the ignition switch.
• When any door is open, the door locks can only be unlocked with the transmit-
ter, and the turn signal light will not flash.
• If you lose one of the transmitters, ask your SUZUKI dealer as soon as possible
for a replacement. Have your dealer pro-
gram the new transmitter code in your
vehicle’s memory so that the old code is
erased.
WA R N I N G
Do not activate the dead lock system
if there are occupants in the vehicle.
They will be locked in the vehicle and
cannot unlock the doors from inside.
NOTICE
The transmitter is a sensitive elec-
tronic instrument. To avoid damaging
the transmitter:
• Do not expose it to impacts, mois-ture or high temperature such as
by leaving it on the dashboard
under direct sunlight.
• Keep the transmitter away from magnetic objects such as a televi-
sion.

2-74
BEFORE DRIVING
75RM4-01E
ClockThe display (A) shows the time.
To set the clock, follow “Setting mode”
instructions in this section.ThermometerThe display (B) show s the thermometer.
The thermometer indicates the outside
temperature.
75RM210
If the outside temperature nears freezing,
the message shown in the above illustra-
tion will appear on the display.
NOTE:
The outside temperature indication is not
the actual outside temperature when driv-
ing at low speed, or when stopped.
Fuel consumption / Driving range / Average speed / Driving time /
Total idling stop time (if equi pped) / Total idling fuel saved (if equipped) / Energy flow indicator (if equipped)When there are no warning or indicator messages on the display (C), you can select one
of the following indications to appear on the display: instanta neous fuel consumption,
average fuel consumption, driving range, average speed, driving time, total idling stop
time, total idling fuel saved, energy flow indicator or no indi cation.
75RM405
(a) (d)
(e)
(f)
(c)
(b)
(g)
(h)
(i)
EXAMPLE

2-80
BEFORE DRIVING
75RM4-01E
NOTE:
• If you push and hold the informationswitch (2) to enter the setting mode
when the display (C) shows average fuel
consumption, average speed, driving
time, total idling stop time or total idling
fuel saved, the value will be reset simul-
taneously. If you do not want to reset the
value, push the information switch
quickly to switch the indication of the dis-
play.
• If you turn the ignition switch, press the
engine switch or start to move the vehi-
cle when the display is in the setting
mode, the setting mode will be canceled
automatically.
Distance unit (Odometer / trip meter distance unit setting)You can change the units in which odome-
ter / trip meter / driving range distance is
displayed.
Fuel economy
(Fuel consumption unit setting)
You can change the units that fuel con-
sumption is displayed in.
Language
You can change the language of the infor-
mation display.
Fuel reset
(Average fuel consumption reset setting)
You can change when the value of aver-
age fuel consumption is reset. Temperature (Tempera
ture unit setting)
You can change the units that temperature
is displayed in.
NOTE:
When you change the units that tempera-
ture is displayed in, the automatic heating
and air conditioning system (if equipped)
temperature display units will be changed
automatically.
Clock setting (Adjusting the clock)
• To change the hour indication, push the brightness control switch (4) up or down
repeatedly when the hour indication
appears as reversed color. To change
the hour indication quickly, push and
hold the brightness control switch (4). To
set the hour indication, push the informa-
tion switch (2) and the minute indication
appears as reversed color.
• To change the minute indication, push the brightness control switch (4) up or
down repeatedly when the minute indi-
cation appears as reversed color. To
change the minute indication quickly,
push and hold the brightness control
switch (4). To set the minute indication,
push the information switch (2).
You can also switch the time indication
between 12-hour and 24-hour format. Door lock (Door
unlock setting)
(if equipped)
You can choose either once or twice oper-
ation(s) to unlock all doors (including the
tailgate) by turning the key, or operating
the keyless entry syst em transmitter, key-
less push start system remote controller or
request switch.
If your vehicle is equip ped with the keyless
push start system, you can also turn off or
on the buzzer sound when the door(s)
is(are) locked or unlocked.
Lights (Light setting)
Lane change (Turn signal lights setting)
The turn signal and its indicator can be set
whether they flash three times even if you
return the turn signal control lever immedi-
ately after moving it.
Guide me light setting (Light setting)
(if equipped)
You can change the lighting time of “To
car” function or “To home” function.
Antitheft
(Theft deterrent alarm system setting)
(if equipped)
You can switch the theft deterrent alarm
system from the enabled state to the dis-
abled state, and vice versa.
The state of the theft deterrent alarm sys-
tem is shown on the information display as
follows:
• Mode A: Disabled state
• Mode D: Enabled state

2-91BEFORE DRIVING
75RM4-01E
Vehicle with ENG A-STOP systemWarning and indicator message Master warning
indicator light Sound Cause and remedy
75RM269
Off Off The engine does not s
top automatically by the
ENG A-STOP system, because any of the auto
stop conditions is not met.
Refer to “ENG A-STOP system (engine auto
stop start system)” in the “OPERATING YOUR
VEHICLE” section for details.
75RM270
Off By certain conditions, some kind of sound you will hear
from interior of the vehicle. The engine stalls. Restar
t the engine by turning
the ignition switch or pressing the engine
switch.
Refer to “ENG A-STOP system (engine auto
stop start system)” in the “OPERATING YOUR
VEHICLE” section for details.
75RM271
Off Beep (one time from interior buzzer) The engine will restart soon, because the bat-
tery continues to be disc
harged, some time has
passed since the engin e was stopped automat-
ically, the temperature of the air from the outlets
changes greatly or the defroster is turned on.
Refer to “ENG A-STOP system (engine auto
stop start system)” in the “OPERATING YOUR
VEHICLE” section for details.
Also, the duration time of the ENG A-STOP
system, depending on using the air conditioning
system can be set. Refer to “Setting mode” in
this section.

2-97BEFORE DRIVING
75RM4-01E
To monitor the next oil and oil filter change
timing properly, it is necessary to reset the
odometer reading and the time for the
light. The light will go out after the reset.
For the resetting procedure, it is recom-
mended to consult your SUZUKI dealer. If
you reset it by yourself, follow the proce-
dure described below:
To reset the engine oil life monitoring sys-
tem:
1) Turn the ignition switch to “ON” posi- tion.
2) Push and hold the indicator selector
knob (2) for a while when the display
shows the oil change request light and
oil indicator.
75RM348
3) Push and hold the indicator selectorknob (2), display will change as follows.
When the oil life m onitoring system is
reset, the oil change request light and
oil indicator will go out and then the dis-
play indicates odometer.
75RM274
(6) “OIL” appears
(7) “OIL” blinks
(8) Odometer
ThermometerThe display (D) shows the thermometer.
The thermometer indicates the outside
temperature.
76MH0A042
If the outside temperature drops to freez-
ing, the mark (g) will appear on the display.
NOTE:
• The outside temperature indication is not
the actual outside temperature when
driving at low speed, or when stopped.
• If there is something wrong with the ther-
mometer, or just after the ignition switch
is turned to “ON” position, the display
may not indicate the outside tempera-
ture.
(2)
EXAMPLE
(8)
(7)
(6)
EXAMPLE
(g)
EXAMPLE