2021 MERCEDES-BENZ B-CLASS HATCHBACK clock

+
ENVIR
ENVIR
ONMENT
ONMENT AL NO
AL NOTE
TE Environmen tal
pollution caused byenvironmentally ir re-
sponsible disposal Ty
re sealant contains pollu tants. #
Have the tyre sealant bottle disposed of
professionall y,e.g. at a Mercedes-Benz
Service Centre. #
Stow the tyre sealant bottle, the tyre in0ation
compressor and thewa rning triangle. #
Pull awa
Pull away immediat
y immediat ely.
el y. #
Stop driving aTer appr oximately ten minutes
and check the tyre pressure using the tyre
in0ation compressor.
The tyre pressure must now be at least
130 kPa (1.3 bar/19 psi). &
W WARNING
ARNING Risk of accident due tothe
speci/ed tyre pressure not being attained
If th e speci/ed tyre pressure is not reached,
th e tyre is too badly damaged. The tyre seal-
ant cannot repair the tyre in this instance. The braking and driving
characteristics may be
gr eatly impaired. #
Do not continue driving. #
Consult a quali/ed specialist workshop. Countr
Countr
ies t
ies that hav
hat hav e Mer
e Mercedes-Benz Ser
cedes-Benz Ser vice24h:
vice24h:
yo u will /nd a stic ker with thete lephone number,
e.g. on the B‑pillar on the driver's side. #
Correct the tyre pressure if it is still at least
130 kPa (1.3 bar/19 psi). See the tyre pres-
sure table on the fuel /ller 0ap forva lues.
Incr
Incr easing t
easing t he tyr
he tyre pr
e pressure
essure #
Switch on the tyre in0ation compressor.
Decr
Decr easing t
easing t he tyr
he tyre pr
e pressure
essure #
Remo vethe tyre sealant bottle from the tyre
in0ation compressor. #
Insert the /ller hose in the soc ket of the tyre
in0ation compressor and turn it a quarter turn
clockwise. #
Press pressure release button Cnext to
manome terB.
When t When t he tyr he tyre pr
e pressur
essur e is corr
e is corr ect
ect #
Unscr ewthe /lling hose from theva lve of the
sealed tyre. #
Screw theva lve cap onto theva lve of the
sealed tyre. #
Stow the tyre sealant bottle and the tyre in0a-
tion compressor. #
Drive tothe nearest quali/ed specialist work-
shop and ha vethe tyre, tyre sealant bottle and
/lling hose replaced there. 360
360
Breakdown assistance

T
T
o
o wing ey
wing eye st
e st or
orag
ag e location
e location The
towing eye is under the load compartment
0oor. F
F
itting and r
itting and r emo
emo ving t
ving t heto
he towing eye
wing eye #
Press the mark on co ver1 inwa rds and
re mo ve. #
Screw intheto wing eye clockwise as far as it
will go and tighten.
V
V ehicles wit
ehicles wit h a tr
h a trailer hitc
ailer hitc h:
h:vehicles with a trailer
hitch do not ha veare ar brac ketfo rth eto wing
ey e. Fasten theto w bar tothe trailer hitch. #
Make sure that co ver1 engages in the
bumper when youre mo vetheto wing eye.
* N
NOOTE
TE Damage totheve hicle due toincor-
re ct use of theto wing eye or trailer hitch When a
towing eye or trailer hitch is used to
re co ver a vehicle, theve hicle may be damaged
in the process. #
Only use theto wing eye or trailer hitch to
to w awa y or tow start theve hicle. #
Do not use theto wing eye or trailer hitch
to to wtheve hicle during reco very. T
T
o
o w
w -st
-st ar
arting t
ting t he v
he vehicle
ehicle V V
ehicles wit ehicles wit h aut
h automatic tr
omatic tr ansmission
ansmission
* NO
NOTE
TE Damage tothe automatic transmis-
sion due to tow-starting The au
tomatic transmission may be damaged
in the process of tow- starting vehicles with
automatic transmission. #
Vehicles with automatic transmission
must not be tow- star ted. #
Vehicles with an automatic transmission must
not be tow- star ted.
V V ehicles wit ehicles wit h manual tr
h manual tr ansmission
ansmission #
Obser vethe no tes on towing away
( / page 367). #
If necessar y,allow the engine and exhaust
system tocool down. #
Swit chon the ignition. #
Engage second gear. #
Release the electric parking brake. 370
370
Breakdown assistance

R
The vehicle is on solid, non-slippery and le vel
gr ound.
R The requ ired tyre-change tool kit is available.
% Ifyo ur vehicle is not equipped with the tyre-
ch ange tool kit, consult a quali/ed specialist
wo rkshop to/nd out about sui table tools. #
Apply the electric parking brake manuall y.#
Movethe front wheels tothe straight-ahead
position. #
V
Vehicles wit
ehicles wit h manual tr
h manual tr ansmission:
ansmission: engage
/rst or reve rsege ar. #
V
Vehicles wit
ehicles wit h aut
h automatic tr
omatic tr ansmission:
ansmission: shiTto
position 005D. #
Switch o. theve hicle. #
Make sure that theve hicle cann otbe star ted. #
Place choc ks orother suitable items under the
front and rear of the wheel that is diagonal ly
opposite the wheel you wish tochange. #
If necessar y,remo vethe wheel trim/hub caps
(/ page 384). #
Raise theve hicle (/ page 384). R
R
emo
emo ving and
ving and /tting
/ttingt
the wheel tr
he wheel tr im/hub caps
im/hub caps R
R
eq
eq uir
uir ements:
ements:
R The vehicle is prepared for a wheel change
(/ page 383).
Wheel tr
Wheel tr im
im
The wheel trim co vers the wheel bolts on vehicles
with steel wheels. Before unscr ewing the wheel
bolts, remo vethe wheel trim. #
T
T o r
o r emov
emov e:
e: using bo thhands, carefully reach
into two wheel trim openings and remo vethe
wheel trim. Plas Plas
tic hub cap tic hub cap #
T
To r
o r emov
emov e:
e:turn the centre co ver of the hub
cap anti-clockwise and remo vethe hub cap. #
T
To
o /t:
/t: make sure that the centre co ver of the
hub cap is turned anti-clockwise. #
Position the hub cap and turn the centre co ver
clockwise until the hub cap engages ph ysically
and audibl y. R
R
aising t
aising t he v
he vehicle when c
ehicle when c hanging a wheel
hanging a wheel R R
eq eq uir
uir ements:
ements:
R There are no persons in theve hicle.
R The vehicle has been prepared for a wheel
ch ange (/ page 383).
R The wheel trims and hub caps ha vebeen
re mo ved (/ page 384).
Impor tant no tes on using the jack:
R Use only a vehicle-speci/c jack that has been
appr ovedby Mercedes-Benz toraise theve hi-
cle.
R The jack is only designed forra ising and hold-
ing theve hicle for a short time while a wheel 384
384
Wheels and tyres

#
Turn ratchet 3clockwise until support 2
sits comple tely on jack support point 1and
th e base of the jack lies evenly on thegr ound. #
Turn ratchet 3until the tyre is raised a maxi-
mum of 3 cm from thegr ound. #
Loosen and remo vethe wheel (/ page 387). R
R
emo
emo ving a wheel
ving a wheel R
R
eq
eq uir
uir ements:
ements:
R The vehicle is raised (/ page 384).
When changing a wheel, avoid applying any force
to the brake disks, as this could impair the le vel of
comfort when braking.
* NO
NOTE
TEDamage tothre ading from dirt on
wheel bolts #
Do not place wheel bolts in sand or on a
dirty sur face. #
Unscr ewthe uppermost wheel bolt com-
ple tely. #
Screw cent ring pin 1into theth re ad ins tead
of the wheel bolt. #
Unscr ewthere maining wheel bolts com-
ple tely. #
Remo vethe wheel and, if necessar y,store it in
th e load compartment. #
Notes on removing an emer gency spa rewheel
(/ page 389). F
F
itting a ne
itting a ne w wheel
w wheel R R
eq
eq uir
uir ements:
ements:
R The wheel tobe changed is remo ved and the
cent ring pin is sc rewe d in (/ page 387). &
W WARNING
ARNING Risk of accident from losing a
wheel
Oiled, greased or damaged wheel bolt/wheel
nut thre ads or wheel hub/wheel mounting
bolt thre ads can cause the wheel bolts/wheel
nuts tocome loose.
As a result, you could lose a wheel while driv-
ing. #
Never oil or grease theth re ads. #
Intheev ent of damage totheth re ads,
contact a quali/ed specialist workshop
immediatel y. #
Have the damaged wheel bolts or dam-
aged hub thre ads replaced. #
Do not continue driving. #
Obser vethe information on thech oice of tyres
(/ page 379).
Fo r tyres with a speci/ed direction of rotation, an
ar ro w on the side wall of the tyre indicates the
cor rect direction of rotation. Obser vethe direc-
tion of rotation when /tting. Wheels and tyres
387
387

#
Slide the wheel tobe mounted onto the cen-
tring pin and push it on. #
Obser vethe no tes on /tting an emer gency
spa rewheel (/ page 389). &
W
WARNING
ARNING Risk of injury from tightening
wheel bolts and nuts
If yo u tighten the wheel bolts or wheel nuts
when theve hicle is raised, the jack could tip. #
Only tighten wheel bolts or wheel nuts
when theve hicle is on thegr ound. #
Obser vethe inst ructions and saf ety no tes on
"Changing a wheel" (/ page 379).#
For saf etyre asons, only use wheel bolts which
ha ve been appr oved byMercedes-Benz and
fo rth e wheel in question. #
Tighten the wheel bolts evenly in a diagonal
pattern in the order indicated until they are
/nger-tight. #
Unscr ewand remo vethe centring pin. #
Tighten the last wheel bolt until it is /n ger-
tight. #
Lowe rth eve hicle (/ page 388). Low Low
er
ering t
ing t he v
he vehicle
ehicle aTer
aTera wheel c
a wheel c hange
hange R
R
eq
eq uir
uir ements:
ements:
R The new wheel has been /tted (/ page 387). #
T
To low
o low er t
er the v
he v ehicle:
ehicle: placethera tchet onto
th e he xagon nut of the jack so that the letters
"AB" are visible and turn anti-clockwise. #
Tighten the wheel bolts evenly in a diagonal
pattern in the order indicated 1to5 with
an initial maximum forc e of 80 Nm. #
Tighten the wheel bolts evenly in a diagonal
pattern in the order indicated 1to5 with
th e speci/ed tightening torque of 130 Nm. &
W
WARNING
ARNING Risk of accident due toincor-
re ct tightening torque
The wheels could come loose if the wheel
bolts or wheel nuts are not tightened tothe
prescribed torque. #
Ensure that the wheel bolts or wheel
nuts are tightened tothe prescribed
tightening torque. #
Ifyo u are not sure, do not mo vetheve hi-
cle. Con tact a quali/ed specialist work-
shop and ha vethe tightening torque
ch ecked immediatel y. #
Check the tyre pressure of the ne wly/tted
wheel and adjust it if necessar y.
% The following does not apply if the new wheel
is an emer gency spa rewheel. 388
388
Wheels and tyres