2021 MERCEDES-BENZ B-CLASS HATCHBACK overheating

Selecting t
Selecting t
he massag
he massage pr
e progrogramme f
amme f or t
or the fr
he fr ont
ont
seats
seats Multimedia system:
4 © 5
Comfort 5
Massage #
Select Wave Massage orPulsating Massage .#
Start the prog ram forth e desired seat 0065. #
T
To se
o se t t
t the massag
he massag e int
e intensity
ensity : switc
: switc h
h High
intensity on or o. . R R
ese ese tting seat se
tting seat se ttings
ttings Multimedia system:
4 © 5
Comfort 5
Seat comfort #
Select Îforth e desired seat. #
Con/ rmthe prom pt. Switc
Switc
hing t
hing t he seat heating
he seat heating on/o.
on/o. &
W
WARNING
ARNING Risk of bu rns due torepeatedly
switching on the seat heating
Re peatedly switching on the seat heating can
cause the seat cushion and seat backrest pad-
ding tobecome very hot.
In particular, the health of persons with limited
te mp erature sensitivity or a limited ability to
re act tohigh temp eratures may be a.ected or
th ey may even su.er burn-like injuries. #
Do not repeatedly switch on the seat
heating. To
protect against overheating, the seat heating
may be temp orarily deactivated aTer it has been
switched on repeatedl y.
* N
NO
OTE
TE Damage tothe seats caused by
objects or documents when the seat
heater is switched on When
the seat heater is switched on, over-
heating may occur due toobjects or docu- ments placed on
the seats e.g. seat cushions
or child seats. This could cause damage tothe
seat sur face. #
Make sure that no objects or documents
are on the seats when the seat heater is
switched on. R
R
eq
eq uir
uir ements:
ements:
R The po wer supply is switched on. Seats and st
owing
113
113

&
D
DAN
AN GER
GER Risk of fatal injury due topoison-
ous exhaust gases
If th eta ilpipe is bloc ked or su1cient ventila-
tion is not possible, poisonous exhaust gases
such as carbon monoxide may enter theve hi-
cle. This is the case if theve hicle gets stuck in
sno w,forex ample. #
Keep theta ilpipe and the area around
th eve hicle free from snow when the
ve hicle or the stationary heater is run-
ning. #
Open a wind owonthe side of theve hicle
fa cing away from the wind toensure an
adequate supply of fresh air. &
W
WARNING
ARNING Risk of accident due tothe
brake system overheating
If yo u lea veyour foot on the brake pedal when
driving, the brake system may overheat.
This increases the braking distance and the
brake system can even fail. #
Never use the brake pedal as a foot re st. #
Do not depress the brake pedal and the
accelerator pedal at the same time while
driving. *
N
NOOTE
TE Engine damage due toexcessively
high engine speeds The engine will be damaged if
you drive with
th e engine in theove rrev ving range. #
Do not drive with the engine in theove r-
re vving range. *
N
NOOTE
TE Causing wearto the brake linings by
permanently depressing the brake pedal #
Do not permanently depress the brake
pedal while driving. #
Touse braking e.ect of the engine, shiT
to a lo werge ar in good time. *
N
NOOTE
TE Damage tothe driv etra in and
engine when pulling away #
Do not warm upthe engine while the
ve hicle is stationar y.Pull away immedi-
atel y. #
Avoid high engine speeds and driving at
full thro ttle until the engine has reached
its operating temp erature. *
N
NOOTE
TE Damage tothe catalytic con verter
due tonon-combusted fuel The engine is not
running smoo thly and is mis-
/ring.
Non-combus ted fuel may getinto the catalytic
con verter. #
Only depress the accelerator pedal
slightl y. #
Have the cause recti/ed immediately at
a qu ali/ed specialist workshop. 174 174
Driving and parking

Se
Se
tting A
tting A TTENTION ASSI ST
TTENTION ASSIST
Multimedia system:
4 © 5
Settings 5
Assistance
5 Attention Assist
Se
Se tting op
tting op tions
tions #
Select Standard ,Sensitive orOff .
Sugg
Sugg es
esting a rting a r es
est art ar ea
ea #
Select Suggest rest area .#
Activate or deactivate the function.
If AT TENTION ASSIST de tects fatigue or
increasing lack of attention, it suggests a rest
area in the vicinity. #
Select the suggested rest area.
Yo u are guided tothe selected rest area. Cr
Cr
uise contr
uise control and limit ol and limit er
er F
F
unction of cr
unction of cr uise contr
uise controlol
Cruise control regula testh e speed totheva lue
selected bythe driver.
If yo u accelerate toove rtake, forex ample, the
stored speed is not dele ted. If youre mo veyour fo
ot from the accelerator pedal aTer overtaking,
cruise cont rol will resume speed regulation back
to the stored speed.
Yo u can store any speed abo ve20 km/h up tothe
maximum design speed or up tothe set winter
tyre limit.
Obser vethe no tes on driving systems and your
re sponsibility; you may otherwise failto recognise
dangers (/ page 223).
Display Display s in t
s in the Ins
he Ins tr
trument Display
ument Display
R h (gre y): cruise control is selected but not
yet activated.
R h (gre en): cruise control is active.
A stored speed appears along with theh dis-
pla y.
% The segments extending from the cur rent
stored speed tothe end of the scale, or tothe
set winter tyre limit, light up in the speedome-
te r. Syst Syst
em limits em limits
Cruise control may be unable tomaintain the
stored speed on uphill gradients. The stored
speed is resumed when thegr adient evens out.
Change into a lo werge ar in good time on long and
steep downhill gradients. Take particular no teof
th is when driving a laden vehicle. By doing so, you
will make use of the engine's braking e.ect. This
re lie vesth e load on the brake system and pre-
ve nts the brakes from overheating and wearing
to oqu ickl y.
Do not use cruise control in thefo llowing situa-
tions:
R in tra1c situations which requ ire frequent
ch anges of speed, e.g. in heavy tra1c, on
winding roads
R on slippery roads. Accelerating can cause the
drive wheels tolose traction and theve hicle
could then skid.
R when visibility is poor
F
F unction of t
unction of t he limit
he limiter
er
The limiter restricts the speed of theve hicle. To
re duce the speed tothe set speed, the limiter
applies the brakes automaticall y.232
232
Driving and parking

with
your skin, eyes or clo thing, and do not
swallow it. Do not inhale any vapours. Keep
th e tyre sealant away from children.
Obser vethefo llowing if you come into contact
with the tyre sealant: #
Rinse o. the tyre sealant from your skin
using water immediatel y. #
If tyre sealant gets into your eyes, thor-
oughly rinse them using clean water
immediatel y. #
If tyre sealant has been swallo wed,thor-
oughly rinse out your mouth immediately
and drink plenty of water. Do not induce
vo miting and seek medical attention
immediatel y. #
Change out of clo thing which has come
into contact with tyre sealant immedi-
atel y. #
If an alle rgic reaction occurs, seek medi-
cal attention immediatel y. *
N NO
OTE
TE Overheating due tothe tyre in0ation
compressor running too long #
Do not runth e tyre in0ation compressor
fo r longer than ten minutes without inter-
ru ption. Comply with
the manufacturer's saf ety no tes on
th e stic ker on the tyre sealant bottle.
Ha ve the tyre sealant bottle replaced in a quali/ed
specialist workshop every /ve years. #
Do not remo veany fore ign objects which ha ve
entered the tyre. #
Remo vesticker 1 from the tyre in0ation
compressor housing and a1x it tothe inst ru-
ment cluster within the driver's /eld of vision. #
Remo vesticker 2 from the tyre sealant bot-
tle and a1x it near theva lve on the wheel with
th e defective tyre. Breakdown assistance
357
357

%
V
Vehicles wit
ehicles wit h a tyr
h a tyre pr
e pressur
essur e loss w
e loss w ar
arning
ning
syst
syst em:
em: if an emer gency spa rewheel is /tted,
th e tyre pressure loss warning system cannot
function reliabl y.Only restart the system
again when the emer gency spa rewheel has
been replaced with a new wheel.
V
V ehicles wit
ehicles wit h a tyr
h a tyre pr
e pressur
essur e monit
e monit or
oring sy
ing sy s-
s-
t
t em:
em: if an emer gency spa rewheel is /tted, the
tyre pressure monitoring system cannot func-
tion reliabl y.Fo r a few minutes aTer an emer-
ge ncy spa rewheel is /tted, the system may
still display the tyre pressure of there mo ved
wheel. Only restart the system again when the
emer gency spa rewheel has been replaced
with a new wheel.
Be sure toalso obser vethefo llowing fur ther rela-
te d subjects:
R Notes on tyre pressure (/ page 375)
R Tyre pressure table (/ page 376)
R Notes on /tting tyres (/ page 379)
R Fitting an emer gency spa rewheel
(/ page 383) In0ating
In0ating
t
the emerg
he emerg ency spar
ency spar e wheel
e wheel *
N
NOOTE
TE Overheating due tothe tyre in0ation
compressor running too long #
Do not runth e tyre in0ation compressor
fo r longer than ten minutes without inter-
ru ption. R
R
eq
eq uir
uir ements:
ements:
The emer gency spa rewheel has been /tted cor-
re ctl y. ( / page 383)
Comply with the manufacturer's saf ety no tes on
th e stic ker of the emer gency spa rewheel and on
th e tyre in0ation compressor. #
Remo vethe stic ker with the label 80 km/h
from the tyre in0ation compressor housing
and a1x it tothe inst rument cluster within the
driver's /eld of vision. #
Remo vethe tyre in0ation compressor from the
st ow age space under the luggage compart-
ment 0oor . (/ page 356, 355) #
Pull /ller hose 1and plug 3out of the tyre
in0ation compressor housing. #
Insert plug 7of /ller hose 1inthe soc ket
on the tyre in0ation compressor and then turn
it until plug 7engages. #
Unscr ewthe cap from theva lve on the emer-
ge ncy spa rewheel. #
Screw union nut 2of /ller hose 1onto the
va lve. #
Make sure on and o. switch 4ofthe tyre
in0ation compressor is set to 00. #
Insert plug 3in a soc ket in your vehicle.
R Cigar ette lighter soc ket 390
390
Wheels and tyres

Coolant
Coolant
N
No
ot
tes on coolant
es on coolant
Obser vethe no tes on operating 0uids
(/ page 396). &
W
WARNING
ARNING Risk of /re‑ and injury from
antif reeze
If antifreeze comes into contact with hot com-
ponent parts in the engine compartment, it
may ignite. #
Allow the engine tocool down before
yo uto p up the antifreeze. #
Make sure that no antif reeze spills out
next tothe /ller opening. #
Thoroughly clean the antifreeze from
component parts before starting the
ve hicle. *
N
NOOTE
TE Damage caused byincor rect cool-
ant #
Only use coolant that has been premixed
with there qu ired antifreeze pr otection. Information on coolant is
available at thefo l-
lowing locations:
R Inthe Mercedes-Benz Speci/cation for
Operating Fluids 320.1
- Athttps://be vo.mercedes-benz.com
- Inthe Mercedes-Benz BeVo App
R Ataqu ali/ed specialist workshop *
N NOOTE
TE Overheating at high outside temp er-
atures If an inappropriate coolant is used,
the engine
cooling system is not su1ciently pr otected
against overheating and cor rosion at high out-
side temp eratures. #
Only use coolant appr ovedby Mercedes-
Benz. #
Obser vethe inst ructions in the
Mercedes-Benz Speci/cations for Oper-
ating Fluids 320.1. Ha
ve the coolant regula rly re placed at a quali/ed
specialist workshop. Proportion of antif
reeze concentrate in the engine
cooling system:
R A minimum of 50% (antifreeze pr otection down
to about -37°C)
R A maximum of 55% (antif reeze pr otection
down to-45°C) N No
ot
tes on windscr
es on windscr een w
een washer
asher 0uid
0uid Obser
vethe no tes on operating 0uids
(/ page 396). &
W
WARNING
ARNING ‑ Risk of /re and injury due to
windscreen washer concent rate
Wi ndsc reen washer concent rate is highly 0am-
mable. It could ignite if it comes into contact
with hot engine component parts or the
ex haust system. #
Make sure that no windscreen washer
concent rate spills out next tothe /ller
opening. 404
404
Te
ch nical data

Displa
Displa
y messag
y messag es P
es Possible causes/conseq
ossible causes/consequences and uences and0050
0050Solutions
Solutions
0080
Trans. oil overheated Drive
on with care *T
he transmission is overheating. When the display message is active, start-up and driving characteristics may be tem-
porarily impaired. #
Drive at low engine speed. #
Avoid sporty driving. #
Before pulling away on uphill gradients, let the transmission cool down until the display message disappears.
Parking lock inoperative
Apply the parking brake *T
he transmission is malfunctioning. The park position 005Dcann otbe selected. #
Park theve hicle safel y. #
Use the electric parking brake tosecure theve hicle against rollingaway.
Teaching in transmission
Operate selector lever
Brake for XX seconds Risk
of vehicle rolling *T
he transmission is being taught in. There is a risk of theve hicle rolling away. #
Depress and hold the brake pedal until thete ach-in process has been comple ted.
The electric parking brake is applied automatically during thete ach-in process. #
Switch on theve hicle. #
Select park position 005D, transmission position 005Eor neutral 005C.
Risk of vehicle rolling away
Apply parking brake See
Owner's Manual *T
he transmission position cann otbe reliably identi/ed. #
Use the electric parking brake tosecure theve hicle against rollingaway.
Teaching in transmission
complete *T
he transmission's teach-in process is comple te. All transmission positions can be selected again. 444 444
Display messages and
warning/indicator lamps

Displa
Displa
y messag
y messag es P
es Possible causes/conseq
ossible causes/consequences and uences and0050
0050Solutions
Solutions
Transmission Malfunction
Visit workshop *T
he transmission is malfunctioning.
Consult a quali/ed specialist workshop.
Depress clutch fully to
start engine *Y
ou ha veattem pted tostart theve hicle without depressing the clutch pedal. #
Depress the clutch pedal and then start theve hicle.
*T hevehicle has stalled while theve hicle was pulling away,e.g. because the clutch pedal wasre leased tooqu ickl y. #
Depress the clutch pedal again.
The vehicle will start automaticall y. #
Slowly re leasethe clutch pedal topull away.
Clutch overheated Avoid
pulling away until the warn-
ing goes out *T
he clut chis under considerable load and is overheating.
Av oid frequent pulling away and driving at walking pace over longer distances. #
Stop theve hicle, paying attention toroad and tra1c conditions and lea vetheve hicle running.
The clutch will cool more quickly when theve hicle is running.
or #
If possible, continue driving at a steady speed and remo veyour foot from the clutch pedal. Do not let the clutch
drag.
The clutch will cool while theve hicle is in motion.
When the clutch has cooled down, the display message will disappear.
Auxiliary battery malfunc-
tion (white display message) *T
he auxiliary battery forth e automatic transmission is no longer being charge d. #
Consult a quali/ed specialist workshop. Displ
aymessages and warning/indicator lamps
445 445