2021 HYUNDAI I20 fuel

10-98
Maintenance
The emission control system of your
vehicle is covered by a written limited
warranty. Please see the warranty
information contained in the Service
Passport in your vehicle.
Your vehicle is equipped with an
emission control system to meet all
emission regulations.
There are three emission control systems
which are as follows.
(1) Crankcase emission control system
(2) Evaporative emission control system
(3) Exhaust emission control system
In order to assure the proper function
of the emission control systems, it
is recommended that you have your
car inspected and maintained by
an authorized HYUNDAI dealer in
accordance with the maintenance
schedule in this manual.1. Crankcase emission control
system
The positive crankcase ventilation
system is employed to prevent air
pollution caused by blow-by gases
being emitted from the crankcase. This
system supplies fresh filtered air to the
crankcase through the air intake hose.
Inside the crankcase, the fresh air mixes
with blow-by gases, which then pass
through the PCV valve into the induction
system.
2. Evaporative emission control
system
The Evaporative Emission Control
System is designed to prevent
fuel vapors from escaping into the
atmosphere.
Canister
Fuel vapors generated inside the fuel
tank are absorbed and stored in the
onboard canister. When the engine is
running, the fuel vapors absorbed in
the canister are drawn into the surge
tank through the purge control solenoid
valve.
Purge Control Solenoid Valve
(PCSV)
The purge control solenoid valve
is controlled by the Engine Control
Module (ECM); when the engine coolant
temperature is low during idling, the
PCSV closes so that evaporated fuel
is not taken into the engine. After
the engine warms up during ordinary
driving, the PCSV opens to introduce
evaporated fuel to the engine.
(0,66,21&21752/6<67(0

10-100
Maintenance
Operating precautions for catalytic
converters (if equipped)
WARNING
Fire
• A hot exhaust system can ignite
flammable items under your vehicle.
Do not park, idle, or drive the vehicle
over or near flammable objects, such
as grass, vegetation, paper, leaves,
etc.
• The exhaust system and catalytic
system are very hot while the engine
is running or immediately after the
engine is turned off. Keep away from
the exhaust system and catalytic, you
may get burned. Also, do not remove
the heat sink around the exhaust
system, do not seal the bottom of the
vehicle or do not coat the vehicle for
corrosion control. It may present a
fire risk under certain conditions.Your vehicle is equipped with a catalytic
converter emission control device.
Therefore, the following precautions
must be observed:
• Use only UNLEADED FUEL for petrol
engine.
• Do not operate the vehicle when
there are signs of engine malfunction,
such as misfire or a noticeable loss of
performance.
• Do not misuse or abuse the engine.
Examples of misuse are coasting with
the ignition off and descending steep
grades in gear with the ignition off.
• Do not operate the engine at high idle
speed for extended periods (5 minutes
or more).
• Do not modify or tamper with any
part of the engine or emission
control system. All inspections and
adjustments must be made by an
authorized HYUNDAI dealer.
• Avoid driving with a extremely low fuel
level. Running out of fuel could cause
the engine to misfire, damaging the
catalytic converter.
Failure to observe these precautions
could result in damage to the catalytic
converter and to your vehicle.
Additionally, such actions could void
your warranties.

10-101
10
Diesel particulate filter (DPF)
(if equipped)
The Diesel Particulate Filter (DPF)
system removes the soot in the exhaust
gas. Unlike a disposable air filter,
the DPF system automatically burns
(oxidizes) and removes the accumulated
soot according to the driving condition.
In order words, the active burning by
engine control system and high exhaust
gas temperature caused by normal/high
diving condition burns and removes the
accumulated soot.
However, if the vehicle continues to
be driven at repeated short distance
or driven at low speed for a long time,
the accumulated soot may not be
automatically removed because of low
exhaust gas temperature. More than
a certain amount of soot deposited,
the malfunction indicator light (
)
illuminates.
When the malfunction indicator light
illuminates, it may turn-off after driving
the vehicle at more than 60km/h (37
mph) or at more than second gear with
1500~2500 engine rpm for a certain time
(for about 25 minutes).
If the malfunction indicator light (
) is not turn-off or blinking continuesly
in spite of the procedure, visit a
professional workshop and check the
DPF system. HYUNDAI recommends
to visit an authorized HYUNDAI dealer/
service partner.
If you continue to drive with the
malfunction indicator light blinking for
a long time, the DPF system can be
damaged and fuel consumption can be
worsen and the engine durability can be
worsen by oil dilution.
CAUTION
Diesel Fuel (if equipped with DPF)
We recommend you to use only the
regulated diesel fuels, when your
vehicle is equipped with the DPF
system.
When you use other diesel fuels, which
is high in sulfurs (above 50 ppm) or
contains unspecified additives, it may
damage the DPF system and cause the
white smoke emission.
Lean NOx Trap (if equipped)
The Lean NOx Trap (LNT) system
removes the nitrogen oxide in the
exhaust gas. The smell can occur in the
exhaust gas depending on the quality
of the fuel and it can degrade NOx
reduction performance, please use the
regulated automotive diesel fuel.

10-102
Maintenance
4. Self Regeneration Mode
LCD Type
If the warning message “Self
Regeneration” is stored in inspection
message tap, it is operable in LCD
warning message page.
WARNING
• Make sure the vehicle parked on
safety zone (to avoid the flammables
like grass and traffic accident)
• Check remained fuel above 1/5 of
full level fuel gauge to prevent fuel
overheat
• Open the hood to prevent engine
room overheat
• Self regeneration should be done
only when DPF indicator illuminates
OSU2I089042OSU2I089042
If the warning message “Diesel filter
regeneration required, See owner’s
manual.” appears on the LCD display,
Self Regeneration is required
To initiate Self Regeneration
1. Engage parking brake and shift lever
at P state.
2. Turn on the engine
3. Warm up the engine and check engine
temperature gauge at the middle
position
4. Turn on the air conditioner and set the
blower to the maximum.
5. Turn on the high beam.
6. Operate the rear defog function.
7. Hold the OK button on the LCD
warning message page.
OSU2I089039OSU2I089039
8. Turn off and turn on the engine again.