Page 282 of 298
282
Before Thinking the Product has Malfunctioned
before ThinKing The producT has
malfuncTioned
The current position as shown on the navigation may differ from the actual position under
the following conditions. The following occurrences are not malfunctions:
䠐When driving on Y-shaped roads with narrow angles the current position may be displayed
in the opposite direction.
䠐Within city streets, the current position may be displayed on the opposite side or on an off-
road position.
䠐When changing the zoom level from maximum to a different level, the current position may
become displayed on a different road.
䠐If the vehicle is loaded onto a ferry or a car transport vehicle, the current position may
become stalled on the last position prior to loading.
䠐When driving on a spiral-shaped road.
䠐When driving in mountain regions with sharp turns or sudden brakes.
䠐When entering a road after passing an underground parking structure, building parking
structure, or roads with many rotations.
䠐When driving in heavy traffic with frequent starts and stops.
䠐When driving under slippery conditions, such as heavy sand, snow, etc.
䠐When the tires have recently been replaced. (Especially upon use of spare or studless tires.)
䠐When using tires of improper size.
䠐When the tire pressure for the 4 tires are different.
䠐When the replacement tire is worn or used. (Especially studless tires having passed a
second season.)
䠐When driving near high-rise buildings.
䠐When a roof carrier has been installed.
䠐When a long distance route is calculated while driving on an expressway, in such cases,
continued driving will automatically enable the system to conduct map matching or use
updated GPS information to provide the current position. (In such cases, up to several
minutes may be required.)
Page 284 of 298
284
Before you think the product is defective
before You ThinK The producT is
defecTiVe
1. Errors which occur during the operation or installation of the device may be mistaken as a
malfunction of the actual device.
2.
If you are having problems with the device, try the suggestions listed below.
3.
If the problems persist, contact your dealer.
Problem: There are small red, blue, or green dots on the screen
Possible Cause : Because the LCD is manufactured with technology requiring high point density, a pixel or lighting deficiency may occur within 0.01% of total pixels.
Problem: The sound or image is not working
Possible Cause :
-Has the Switch for the vehicle been turned to [ACC] or [ON]?
-Has the SYSTEM been turned OFF?
Problem: The screen is being displayed but sound is not working
Possible Cause :
-Has the volume been set to a low level?
-Has the volume been muted?
Problem: When the power is turned on, the corners of the screen are dark
Possible Cause :
-The display appearing somewhat dark after prolonged periods of use is normal with LCD panels. It is not a malfunction.
-If the screen is very dark, contact your nearest dealer for assistance.
Problem: Sound is working from only one speaker
Possible Cause : Are the positions of Fader or Balance sound controls adjusted to only one side?
Problem: The external device is not working
Possible Cause : Is the external device connected with a standard connector cable?
Problem: When turning power on, the most recent mode screen is not displayed
Possible Cause :
-Within modes that play files by reading external sources, such as USB or Bluetooth® streaming mode, the most recently played mode screen prior to turning off power may not properly load.
-If there is no the corresponding device is not connected, the mode operated prior to the most recent mode will operate.
-If the previous mode still cannot be properly played, the mode operated prior to that will operate.
Page 285 of 298
285
Troubleshooting
TroubleshooTing
Problem: The power does not turn on.
䠐Possible Cause : The fuse is disconnected.
䠐Countermeasure:
-Replace with a suitable fuse.
-If the fuse is disconnected again, please contact your dealer.
䠐Possible Cause : Device is not properly connected.
䠐Countermeasure: Check to see that the device has been properly connected.
Problem: The system does not play.
䠐Possible Cause : The vehicle battery is low.
䠐Countermeasure: Charge the battery if the problem persists, contact your point of purchase or service center.
Problem: The image colour/tone quality is low.
䠐Possible Cause : The brightness, saturation, and contrast levels are not set properly.
䠐Countermeasure: Properly adjust the brightness, saturation, and contrast levels through Display Setup.
Problem: Sound does not work.
䠐Possible Cause : The volume level is set to the lowest level.
䠐Countermeasure: Adjust the volume level.
䠐Possible Cause : The connection is not proper.
䠐Countermeasure: Check to see that the device has been properly connected.
䠐Possible Cause : The device is currently fast-forwarding, rewinding, scanning, or playing in slow mode.
䠐Countermeasure: The sound will not work when the device is fast-forwarding, rewinding, scanning, or playing in slow mode.
Problem: The sound or image quality is low.
䠐Possible Cause : Vibration is occurring from where the conversion switch has been installed.
䠐Countermeasure: The sound may be short circuited and the image distorted if the device vibrates.
Page 295 of 298
295
trademarks and licenses
copYrighT for brand icon
The marks of companies displayed by this product to indicate business locations are the
marks of their respective owners. The use of such marks in this product does not imply any
sponsorship, approval, or endorsement by such companies of this product.
copYrighT for junc Tion View
Junction View Data provided by ZENRIN USA, INC. Copyright(C) 20XX, All rights Reserved.
abouT map updaTes
You can contact your dealer.
Information:
This product requires regular updates for new functions and map updates. Updating may
require up to 1 hour depending on the data size.
Turning off the power or ejecting the USB during the update process may result in damage to
the system. Make sure to keep the ignition on and wait until updating is complete.
CAUTION:
䠐The use of an uncertified USB may result in damage to the system due to heat related
deformation.
䠐Product malfunctions caused by the use of an uncertified cards shall not be covered within
the product warranty.
䠐Repeatedly connecting/disconnecting the USB in a short period of time may cause damage
to the device.