BFGOODRICH® TIRES
37
manufacturer’s specification due to the actual load on that wheel
position. Some vehicles may have different sized tires mounted on the
front and rear axles, and these different sized tires have rotation
restrictions. Always check the vehicle Owner’s Manual for the proper
rotation recommendations.
FULL-SIZE SPARE
Full-size spare tires (not temporary spares) of the same size and
co
nstruction should be used in a five tire rotation. Always check the
inflation pressure of the full-size spare immediately before
incorporating it into rotation. Follow the vehicle manufacturer’s
recommended pattern for rotation, or if not available, see a qualified
tire technician.
REPLACEMENT OF TWO TIRES
It is recommended that all four tires are replaced at the same time.
Ho
wever, whenever only two tires are replaced, the new ones should
be put on the rear. The new tires, with deeper tread, may provide
better grip and water evacuation in wet driving conditions.
CUSTOMIZATION OF TIRES, WHEELS, OR SUSPENSION ON
SU
VS AND LIGHT TRUCKS
Due to their size, weight and higher center of gravity, vehicles such as
SU
Vs and light trucks do not
have the same handling characteristics
as automobiles. Because of these differing characteristics, failure to
operate your SUV/truck in a proper and safe manner can increase the
likelihood of vehicle rollover. Modifications to your SUV/truck tire
size, tire type, wheels or suspension can change its handling
characteristics and further increase the likelihood of vehicle rollover.
Whether your SUV/truck has the original equipment configuration
for tires, wheels and suspension or whether any of these items have
been modified, always drive safely, avoid sudden, sharp turns or lane
changes and obey all traffic laws. Failure to do so may result in loss of
vehicle control leading to an accident and serious injury or death.
TIRE ALTERATIONS
Do not make or allow to be made any alterations on your tires.
Al
terations may prevent proper performance, leading to tire damage
which can result in an accident. Tires which become unserviceable due
to alterations such as trueing, whitewall inlays, addition of balancing
or sealant liquids, or the use of tire dressing containing petroleum
distillates are excluded from warranty coverage.
BFGOODRICH® TIRES
40
road. If a tire is mounted by error on the wrong-sized rim, do not
remount it on the proper rim — scrap it. It may have been damaged
internally (which is not externally visible) by having been
dangerously stretched and could fail on the highway.
Old valves may leak. When new tubeless tires are mounted, have
ne
w valves of the correct type installed. Tubeless tires must only be
mounted on wheels designed for tubeless tires i.e., wheels which
have safety humps or ledges.
It is recommended that you have your tires and wheels balanced. Tires
an
d wheels which are not balanced may cause steering difficulties, a
bumpy ride, and irregular tire wear.
Be sure that all your valves have suitable valve caps. The valve cap
is
the primary seal against air loss.
SERVICE LIFE FOR PASSENGER CAR AND LIGHT TRUCK TIRES
IN
CLUDING SPARE TIRES
The following recommendation applies to passenger car and light
tr
uck tires. Tires are composed of various types of material and rubber
compounds, having performance properties essential to the proper
functioning of the tire itself. These component properties evolve over
time. For each tire, this evolution depends upon many factors such as
weather, storage conditions, and conditions of use including load,
speed, inflation pressure, maintenance etc. to which the tire is
subjected throughout its life. This service-related evolution varies
widely so that accurately predicting the serviceable life of any specific
tire in advance is not possible.
In addition to regular inspections and inflation pressure maintenance
by
consumers, it is recommended to have passenger car and light
truck tires, including spare tires, inspected regularly by a qualified tire
specialist, such as a tire dealer, who will assess the tire’s suitability for
continued service. Tires which have been in use for five years or more
should continue to be inspected by a specialist at least annually.
Consumers are strongly encouraged to be aware not only of their tires’
vi
sual condition and inflation pressure but also of any change in
dynamic performance such as increased air loss, noise or vibration,
which could be an indication that the tires need to be removed from
service to prevent tire failure.
BRIDGESTONE® - FIRESTONE®
56
TIPS FOR SAFE LOADING
• Always keep the vehicle manufacturer’s recommended inflation
p
ressure in all your tires, including the spare. Check their pressure
monthly and before long trips or carrying extra weight.
• Never exceed the maximum load rating stamped on the sidewall of
y
our tire.
• Never exceed the Gross Vehicle Weight Rating (GVWR) or front/ r
ear Gross Axle Weight Rating (GAWR) of your vehicle.
• Consult your vehicle Owner’s Manual for load recommendations
a
nd special instructions such as for trailer/towing and snow plow
installations.
TIRE DAMAGE, INSPECTION AND SERVICE LIFE
Evaluation and maintenance of your tires is important to their
pe
rformance and the service they provide to you. Over time and/or
through use, the condition of a tire can change from exposure to
everyday road conditions, the environment, damaging events such as
punctures, and other external factors.
WARNING!
Driving your vehicle in an overloaded condition is dangerous.
Ov
erloading causes excessive tire heat build-up and internal
structural damage. This can cause a tire failure, even at a later
date, which could lead to serious personal injury or death.
Consult the vehicle tire information placard, certification label,
and owner’s manual for the recommended vehicle load limits and
loading recommendations.
WARNING!
Driving on damaged tires is dangerous. A damaged tire can
su
ddenly fail causing serious personal injury or death. Have your
tires regularly inspected by a qualified tire service professional.
GOODYEAR® DUNLOP® TIRES
122
replacement, the difference in price will be at an additional charge to
you. Any replacement tire provided pursuant to this warranty will be
covered by the warranty in effect at the time of replacement.
ADDITIONAL PROVISIONS
A tire has delivered its full original tread life and the coverage of this
li
mited warranty ends when the tread wear indicators become visible
(worn to 2/32") or six years from the date of new tire purchase,
whichever occurs first. Without proof of purchase the date of
manufacture will be used to determine eligibility.
LIMITATIONS
This limited warranty is applicable only in the United States and
Ca
nada.
WHAT IS NOT COVERED BY THIS WARRANTY?
This limited warranty does not cover the following:
• Tires submitted for ride disturbance complaints that are worn
b
eyond the first 2/32 nds of an inch (2/32") tread depth or tires
submitted for ride disturbance due to damaged wheels or any
vehicle condition.
• Goodyear® does not warrant or give credit in any adjustment trans- a
ction for any kind of material added to a tire (e.g., tire fillers, seal -
ants, balancing substances) after the tire leaves a factory producing
Go
odyear® or Dunlop® tires, nor will it adjust any tire that has
failed as a result of adding such material.
• Irregular wear or damage due to mechanical condition of the
v
ehicle, improper inflation, overloading, high speed spin-up,
misapplication, misuse, negligence, racing, use of tire chains,
improper mounting or demounting, improper repair, wreck, colli -
sion or fire.
• Road hazards (includes, but is not limited to, punctures, cuts, snags,
i
mpact breaks, etc.).
• Any tire that, after leaving a factory producing Goodyear® or
D
unlop® tires, has been intentionally altered to change its appear -
ance (e.g., white inlay on a black tire or regrooved).
• Tires with weather-cracking that were purchased more than four
y
ears prior to presentation for adjustment or, if purchase date
cannot be verified, manufactured more than four years prior to
presentation for adjustment.
GOODYEAR® DUNLOP® TIRES
131
HOW TO READ A TIRE DOT SERIAL NUMBER
DOT stands for Department of Transportation and the number is on
th
e lower sidewall of each tire to show that the tire meets or exceeds
the Department of Transportation safety standards.
TIRE SERVICE LIFE
Tires are designed and built to provide many thousands of miles/
k i
lometers of excellent service. For maximum benefit, tires must be
maintained properly to avoid tire damage that may result in removal
from service before the tread is worn down to minimum depth.
It is not practical to accurately predict the service life of any specific
ti
re in chronological time since service conditions vary widely. The
serviceability of a tire over time is a function of the storage and service
conditions (inflation pressure, load, speed, road hazard injury, etc.) to
which a tire is subjected. Consumers should not rely solely on the
appearance of the tire, but should be aware of any change in dynamic
performance such as increased air loss, noise or vibration, which could
be a sign to remove the tire. Therefore, it is essential to have tires,
including spares, inspected regularly (at least monthly) for proper
inflation pressure, damage and treadwear.
Check your vehicle’s Owner’s Manual (or your vehicle) to
de
termine if it is equipped with run-flat (extended mobility) tires.
If your vehicle is equipped with run-flat tires, the following applies:
RUN-FLAT TECHNOLOGY EXTENDED MOBILITY TECHNOLOGY
(E
MT™), RUNONFLAT® (ROF) AND DUNLOP® SELF-SUPPORTING
TECHNOLOGY (DSST®) ORIGINAL EQUIPMENT TIRES
KUMHO TIRES
144
4. The cost of applicable taxes and mounting and balancing and any
other service charges.
5. Tire damage or irregular wear due to: 1
. Road hazard, including puncture, cut, impact break, bulge,
s
nag, stone drill, collision.
2. Continued use while run flat or under acute under-inflation.
3
. Improper use or operation, without limitation, improper infla -
t
ion pressure, overloading, use of an improper rim, tire/wheel
as
sembly imbalance or other vehicle condition, worn suspen -
sion components, improper mounting or de-mounting, misuse,
mi
sapplication, fire or other externally generated heat, water or
other material trapped inside the tire during mounting, tire
alteration, racing or competition purposes, improper inserting
of sealant, balance or filler materials.
4. Improper repair, or with repairs not conforming to the Rubber
M
anufacturers Association standards, or with section repairs,
or with self-vulcanizing plug only.
5. Failure to rotate the tire at least every 5,000
miles (8,047 km) as
ev
idenced by Kumho’s Mileage Warranty/Tire Rotation Card
(printed in this brochure) or vehicle misalignment.
6. Uneven or rapid wear which is caused by mechanical irregu -
l
arity in the vehicle such as misalignment, (a measured tread
di
fference of 2/32nds of an inch or more across the tread on the
same tire).
6. Ozone or weather cracking on tires over four (4) years from the
d
ate of manufacture.
7. Tires that have been recapped, or retreaded, regrooved.
8
. Ride disturbance (out-of-round, vibration, pulling, etc.) claims
s
ubmitted after the first 2/32" of tread wear.
9. Loss of time, or use, inconvenience, or any incidental or consequen -
t
ial damage.
10. Tires that have been modified by the addition or removal of mate -
r
ial or any tire intentionally altered to change its appearance.
11. Tires unserviceability caused by the tire operation in excess of tire/ w
heel manufacturers specifications and recommendations.
MICHELIN®
174
When rotating tires with a directional tread pattern, observe the
arrows molded on the sidewall which show the direction the tire
should turn. Care must be taken to maintain the proper turning
direction.
Some Tire Pressure Monitoring Systems (TPMS) may not recognize
th
at a tire has been moved to a different position on your vehicle.
Make certain that your TPMS system is reset, if necessary, so as to
correctly identify the location of each tire on your vehicle. Refer to
your vehicle owner’s manual or your vehicle dealer.
Determine whether rotated tires require tire inflation adjustment as
fr
ont and rear position tire pressure may vary according to the vehicle
manufacturer’s specification due to the actual load on that wheel
position. Some vehicles may have different sized tires mounted on the
front and rear axles, and these different sized tires have rotation
restrictions. Always check the vehicle owner’s manual for the proper
rotation recommendations.
Full-size Spare
Full-size spare tires (not temporary spares) of the same size and
co
nstruction should be used in a five tire rotation. Always check the
inflation pressure of the full-size spare immediately before
incorporating it into rotation. Follow the vehicle manufacturer’s
recommended pattern for rotation, or if not available, see a qualified
tire technician.
Replacement of Two Tires
It is recommended that all four tires are replaced at the same time.
Ho
wever, when only two tires are replaced, the new tires should be
put on the rear. The new tires, with deeper tread, may provide better
grip and water evacuation in wet driving conditions.
CUSTOMIZATION OF TIRES, WHEELS, OR SUSPENSION ON
SU
VS AND LIGHT TRUCKS
Due to their size, weight and higher center of gravity, vehicles such as
SU
Vs and light trucks do not have the same handling characteristics
as automobiles. Because of these differing characteristics, failure to
operate your SUV/truck in a proper and safe manner can increase the
likelihood of vehicle rollover. Modifications to your SUV/truck tire
size, tire type, wheels or suspension can change its handling
characteristics and further increase the likelihood of vehicle rollover.
Whether your SUV/truck has the original equipment configuration
for tires, wheels and suspension or whether any of these items have
MICHELIN®
179
SERVICE LIFE FOR PASSENGER CAR AND LIGHT TRUCK TIRES
INCLUDING SPARE TIRES
The following recommendation applies to passenger car and light
tr
uck tires. Tires are composed of various types of material and rubber
compounds, having performance properties essential to the proper
functioning of the tire itself. These component properties evolve over
time. For each tire, this evolution depends upon many factors such as
weather, storage conditions, and conditions of use (load, speed,
inflation pressure, maintenance etc.) to which the tire is subjected
throughout its life. This service-related evolution varies widely so that
accurately predicting the serviceable life of any specific tire in advance
is not possible.
That is why, in addition to regular inspections and inflation pressure
m a
intenance by consumers, it is recommended to have passenger car
and light truck tires, including spare tires, inspected regularly by a
qualified tire specialist, such as a tire dealer, who will assess the tire’s
suitability for continued service. Tires which have been in use for five
years or more should continue to be inspected by a specialist at least
annually. Consumers are strongly encouraged to be aware not only of
their tires’ visual condition and inflation pressure but also of any
change in dynamic performance such as increased air loss, noise or
vibration, which could be an indication that the tires need to be
removed from service to prevent tire failure. It is impossible to predict
when tires should be replaced based on their calendar age alone.
However the older a tire the greater the chance that it will need to be
replaced due to the service-related evolution or other conditions
found upon inspection or detected during use.
While most tires will need replacement before they achieve 10 years,
i t
is recommended that any tires in service 10 years or more from the
date of manufacture, including spare tires, be replaced with new tires
as a simple precaution even if such tires appear serviceable and even
if they have not reached the legal wear limit. For tires that were on an
original equipment vehicle (i.e., acquired by the consumer on a new
vehicle), follow the vehicle manufacturer’s tire replacement
recommendations, when specified (but not to exceed 10 years).
The date when a tire was manufactured is located on the sidewall of
ea
ch tire. Consumers should locate the Department of Transportation
(DOT) code on the tire which begins with DOT and ends with the
week and year of manufacture. For example, a DOT code ending with
“2204” indicates a tire made in the 22nd week (May) of 2004.