2021 AUDI Q2 door lock

Seats and storage

CO

rN

•-i

00
children unsupervised in the vehicle with the
key.
© CAUTION
- To avoid damage, please take care when de­
taching connectors from the electrical pow­
er sources.
-To avoid damage to the vehicle's electrical

system,
never connect equipment that
gen­

erates electrical current, such as a solar
panel or battery charger, to the power sour­
ces in order to charge the vehicle's battery.
- Always use the correct type of plugs to
avoid damaging the power sources.
©
USB charging sockets marked "CHARGE ON­
LY" cannot transfer data and are intended for
charging only.
Storage
Cup holders

/

Fig.
56

BfT

^^—- j
^^ m /

Detail of the rear seat bench: Rear cup holder*

r^
n
co
3
>
CO
m

A

Your vehicle has cup holders in the front centre
console, in the door trim and in the rear centre
armrest*.
Rear cup holders*
• Swivel the centre armrest downwards.
• To open the cup holder, press the button

•=>
Fig.
56.
• Place your drinks in the holder.
• To close the cup holders, sLide the cover back
until it engages.
A WARNING
- Do not put any hot drinks in the cup holders
while the vehicle is moving. You could be
scalded if the hot liquid is spilt.
- Do not use cups, mugs or glasses made
from hard materials such as glass or porce­

lain.
These could cause injury in the event of
an accident.
© CAUTION
You should avoid putting open drinks contain­
ers in the cup holders. The drinks could other­
wise spill over and cause damage to e.g. the
electrical equipment or the seat covers.
Further storage compartments and
retainers
You will find further storage compartments and
retainers at various points in the vehicle:
- Glove box: The glove box can be Locked* with
the key
- Storage compartment underneath the front
centre armrest*
- Storage compartment at the front end of the
front seats*. This compartment can hold ob­
jects weighing up to 1 kg
- Coat hooks* above the rear doors
- Side retaining hooks* in the luggage compart­
ment
A WARNING
- To avoid the risk of injuries, always keep the
glove box Lid closed when driving.
- The storage compartments in the door trims
should only be used to store small objects.
Make sure that they are stored safely inside
the compartment, as otherwise they might
impair the protection offered by the side air-

bags.

- The retaining hooks should only be used to
hold objects weighing up to 3 kg. Heavier
objects cannot be safely secured - risk of in­
jury!
61

Driving

CO

<
O
rN
IV
rN
t-H
o <
® For the sake of the environment
Do not warm up the engine by running it with
the car stationary. You should drive off imme­
diately whenever possible. This will help avoid
unnecessary exhaust emissions.
© Note
- Any noises which may be heard when the
engine is started are quite normal and no
cause for concern.
- If
you
leave your vehicle with the ignition
switched on, it will be switched off auto­
matically after
a
while. Please note that
electrical equipment such as the exterior
lighting will also be switched off.
Switching off the engine
Applies to: vehicles with convenience key

•
Stop the vehicle.

•
Automatic gearbox: Move the selector lever to
position P.

•
Press the ISTART ENGINE STOP| button

tapage
76, Fig. 70.
Steering
lock15

The steering will be locked if
you
switch off the
engine with the ISTART ENGINE STOP| button,
move the selector lever to position P (on vehicles
with automatic gearbox*) and open the driver's
door. The steering lock acts as a theft deterrent.
Emergency Off function
If necessary in an emergency, the engine can be
switched off while the vehicle is still moving at
speeds of 7 km/h and above. To switch off the
engine, press the ISTART ENGINE STOP| button
twice in quick succession or hold it in for longer
than two seconds.
A WARNING
- Never switch off the engine until the vehicle
is stationary. Otherwise you may not have
the full benefit of the brake servo and pow­
er steering. You may need more strength to
steer and brake the vehicle than you nor­
mally would. This would mean a greater risk
of accidents and serious injury, because you
cannot steer and brake in the normal
man­

ner.
- Always take the key with you when you Leave
the vehicle. Otherwise the engine can be
started or power-operated equipment such
as the electric windows can be used. This
could result in serious injury.
- When parking, always move the selector
lever to position
P
to prevent the vehicle
from rolling back accidentally.
If the engine has been working hard for
a
long

time,
there is a risk of heat building up in the
engine compartment after the engine has
been switched off; this could cause engine
damage. For this reason, you should leave the
engine idling for about 2 minutes before
switching it off.
©
Note

After the engine is stopped, the radiator fan
may remain on or turn itself back on for up to
10 minutes, even if the ignition is switched
off. This may occur for the following reasons:
- Residual heat has raised the coolant
tem­

perature.
- Direct sunlight has additionally heated up
the engine compartment while the engine is

warm.

- Applies to vehicles with diesel particulate
filter: The emission control system is hot
because of the regeneration process, even
though the engine has
not
yet reached oper­
ating temperature.
Driver messages
Engine running. Warning! Switch off ignition
before leaving car

1J
This function is not available on all export versions.
77

Driving
This message appears
and a
buzzer sounds
if
you
open
the
driver's door while
the
engine
is
run­

ning.

Pressing start/stop button again will switch
off

engine.
This message appears
if
you press
the

ISTART
ENGINE
STOPI*
button while
the
vehicle
is moving
<^>page
77,
Emergency
Off
function.
Engine start system: fault. Please contact work­
shop
A fault
has
occurred when starting
the
engine
au­

tomatically (automatic start function). Drive
to a

qualified workshop soon
and
have
the
fault
recti­

fied.
To
start
the
engine, turn
the
ignition
key to

position
@
^>page
74 or
press

the
ISTART
ENGINE
STOPl
button and hold the

key/button until
the
engine starts.

D
Key not
recognised. See owner's manual
This message appears
if
there
is no
convenience
key inside
the
vehicle
or if
the system cannot
de­

tect
or
identify
the
key. This
can
happen,
for ex­

ample,
if
the radio signal from
the key is
obstruc­
ted
by a
metal briefcase
or
similar,
or if the key

battery
is
weak. Electronic equipment, such
as

mobile phones,
can
also interfere with
the
radio
signal from
the key.

The engine
can
still
be
started
or
stopped
if
this
happens (please refer
to
^page
79).

C]
Remote control key: hold back
of key

against marked area.
See
owner's manual
If
the
indicator lamp lights
up and the
message
appears,
a
malfunction
has
occurred

^>page
79.

3
Key not in
vehicle?

3
Remote control key:
key not
recognised.
Is

key still
in
vehicle?
If
the
indicator
lampGB
Lights
up and the
mes­
sage appears,
the
convenience
key
was removed
from
the
vehicle while
the
engine
was
running.
If

the convenience
key is not in the
vehicle
you
will
not
be
able
to
switch
on the
ignition
or
restart
the engine after
it has
been switched
off. You
will
also
not be
able
to
lock
the
vehicle from
the
out­

side.

Please press brake pedal
This message appears
on
vehicles with
an
auto­
matic gearbox
if
you
try to
start
the
engine
with­

out first pressing
the
brake pedal.
Please press clutch pedal
This message appears
if
you
try to
start
the en­

gine without first pressing
the
clutch pedal.
The

engine will only start
if
you press
the
clutch
ped­

al.

Please engage
N or P

This message will appear
if
you
try to
start
or

switch
off the
engine when
the
selector lever
is

not
in N or P. The
engine
can
then
not be
started
or switched
off.

Switch
off
ignition before leaving
car.
Battery
is

being discharged
This message appears
and the
buzzer sounds
if

you open
the
driver's door while
the
ignition
is

switched
on.
Switch
off
the ignition
to
prevent
the vehicle battery from being discharged.
Shift
to P,
vehicle can roll away. Doors can only
be locked
in P

For safety reasons, this message will appear
if

the selector Lever
of the
automatic gearbox
is not

in position P when
you
switch
off the
ignition.
Put

the selector lever
in
position
P;
otherwise
the ve­

hicle
can
roll away
and
cannot
be
locked.
78

Driving
start moving immediately and could cause
an accident.
- You should only use the emergency braking
function in a real emergency, for example if
the brake system were to fail or if the brake
pedal were to be obstructed. If
you
use the
emergency braking function by activating
the parking brake switch, this has the same
effect as heavy braking. Please remember
that the ESC (and the integrated ABS, EDL
and traction control functions) is still sub­
ject to certain physical limits. In a corner or
in bad road or weather conditions an emer­
gency stop can cause the vehicle to skid or
lose steering control.
- It is not possible to apply the parking brake
if the electrical power supply fails. In this

case,
park the vehicle on a
level
surface and
select 1st gear (manual gearbox) or move
the selector lever to position
P
(automatic
gearbox) to prevent
it
from rolling. Obtain
professional assistance.
- Always take the key with you when leaving
your
vehide
- even if
you
only intend to be
gone for
a
short time. This is especially im­
portant if children are left in the car. They
might otherwise be able to start the engine,
release the parking brake or use power-op­
erated equipment such as the electric
win­

dows - this could lead to injuries.
- Do not leave anyone (especially children) in
the vehicle when it is locked. Locked doors
could delay assistance in an emergency, po­
tentially putting lives at risk.
© Note
Applies to: vehicles with automatic gearbox
You can apply the parking brake manually or
switch on the hold assist* when stopping at
traffic lights, etc. You do not then have to
hold the car with the brake pedal, as the
brakes will stop it creeping forward while a
gear is engaged in the automatic transmis­

sion.
When you drive off in the normal way,

co
the parking brake will be released automati-
<

° cally
and your vehicle will start moving

2 •=>
page 83. o < 00

O
Note
- Any slight noise which may be heard when
the parking brake is applied or released is
quite normal and no cause for concern.
- The parking brake runs an automatic test
cycle at regular intervals when the vehicle is

parked.
This may cause a slight noise, which
is normal.
- If the electrical power supply fails, it is not
possible to release the parking brake (if it
was applied) or to apply the parking brake
(if it was released)
•=> A-
Obtain professional
assistance.
Driving away from a
standstill
Various features and safety functions are availa­
ble for driving off, depending on the equipment
in your vehicle.
Hill starting with the parking brake applied
Important: The driver's door must be closed.

•
To drive off more easily on a slope, apply the
parking brake and drive off just as you usually

would.
The parking brake will be released auto­
matically, but not until there is enough power
at the wheels to make the vehicle move in the
desired direction.
Hill starting with the hill hold assist
The hill hold assist function makes it easier to
drive away on a slope.
Important: The driver's door must be closed and
the engine must be running.

•
To activate the hill hold assist, press and hold
the brake pedal for several seconds. The vehicle
must be on a slope and facing uphill.
When you release the brake pedal the braking
force will be maintained for
a
moment
^^
in
order to hold the vehicle and make it easier for
you to drive away. •
83

Driving
Driving off with the hold assist
Applies to: vehicles with hold assist
The hold assist helps the driver if the vehicle is
stationary for a Long period or very often, for in­
stance at traffic lights, on steep gradients or in
stop-and-go traffic.
Important: The driver's door must be closed and
the engine must be running.
• To switch the hold assist on/off, press the but­
ton
«59 © ^>page
82, Fig. 74,
•=»^.
The LED in
the button will light up or go out.

•
Once it detects that the vehicle has stopped,
the hold assist keeps the vehicle stationary. In
this case, a green indicator Lamp
^
Lights up in
the instrument cluster. You can now take your

foot
off the brake pedal.

•
Drive off in the normal way: the brake will be
released automatically and the vehicle will
start moving.
In certain situations, the hold assist transfers the
job of holding the vehicle to the parking brake.
As soon as the parking brake is holding the
vehi­

cle
still,
the warning lamp || appears in the in­
strument cluster. In addition, the LED in the ®)
button will light up.
Driver messages in the instrument cluster
display

P.]
Hold assist: unavailable
If this message appears, the hold assist is un­
available or the system requirements have not
been met.
A WARNING
Applies to: vehicles with hill hold assist
If
you
do not drive away immediately after re­
leasing the brake pedal, or if the engine

stalls,
the vehicle could start to roll back. You
should therefore immediately press the brake
pedal or apply the parking brake.
A WARNING
The intelligent technology in the hold assist*
and hill hold assist functions cannot defy the
laws of physics. Do not let the extra conven­
ience afforded by the hold assist* and hill
hold assist functions tempt you into taking
any risks when driving - this can cause
acci­

dents.

- The hold assist* and hill hold assist func­
tions cannot keep the vehicle stationary in
all conditions on a gradient (e.g. if the road
is slippery or icy).
- Always ensure that the vehicle is stopped
properly and safely - risk of accident!

(T)
CAUTION
Switch off the hold assist* function before
driving the vehicle into a car wash.

©
r
Note
Applies to: vehicles with automatic gearbox
When the hold assist* function is switched

on,
it stops the vehicle from creeping for­
wards when you take
your
foot off the brake

pedal.

Off-road driving
General notes
The functions of the electronic stabilisation
con­

trol (ESC) have been augmented to provide extra
assistance when driving off-road. The
ESC
off-
road mode can be activated in situations when it
would be advantageous for the wheels to lock, or
when a differential Lock would normally be re­
quired
^>page
146.
This Audi model is not an off-road vehicle, how­
ever. When driving off-road you are advised to
avoid tracks or terrain which are not suited to
the design of the car and your own driving skills
and experience. Do not take any risks.
After driving off-road
- After driving, remove any pieces of foliage or
other objects which may be caught in the radia­
tor grille, under the car or in the wheels. In par­
ticular, inspect the tyre treads for stones.
- Clean the bodywork and underside of the
vehi­

cle and check the underside for possible dam­

age.

- Remove dirt from the windows, headlight
len­

ses and number plates. •
84

Driving
©
y Note

If the selector lever does not lock automati­
cally, a malfunction has occurred. In this case,
the power transmission is interrupted to pre­
vent the vehicle from moving unintentionally.
Proceed as follows to engage the selector lev­
er lock again:
- Applies to vehicles with 6-speed gearbox:
Briefly press the brake pedal.
- Applies to vehicles with 7-speed gearbox:
Press the brake pedal. Move the selector
lever to position
P
or
N
and then select a
gear.
- If the vehicle does not move forwards or
backwards even though a gear is selected,
proceed as follows:
- If the vehicle does not move in the desired

direction,
the system may have failed to en­
gage the gear correctly. In this case, press
the brake pedal and select the gear again.
- If the vehicle still does not move in the de­
sired direction, a system malfunction has

occurred.
Seek professional assistance and
have the system checked.
General notes on driving an automatic
Applies to: vehicles with automatic gearbox

Fig.
77 Detail of the centre console: Selector lever with in­
terlock button
Starting the engine

•
Move the selector Lever to
P
or N. In the case of
Low outside temperatures (below -10 °C), the
engine can only be started when the selector
lever is in position P.
Driving away from a standstill

•
Press and hold the brake pedal.

•
Press and hold the interlock button (the button
in the selector lever handle), set the selector
lever to the desired position (e.g. D)
^>page
86
and release the interlock button.

•
Wait for the gearbox to engage the gear (a
slight movement can be felt).

•
Release the brake and press the accelerator
There are several convenient functions to help
you drive away on gradients
^page
83.
Stopping briefly

•
Press the brake pedal to hold the vehicLe when
stationary (for instance at traffic lights).

•
Do not press the accelerator.

•
To prevent the vehicLe from rolling away, apply
the parking brake before moving off on steep
gradients
•=>^
and
•=>(]).

• As soon as you acceLerate as normal, the park­
ing brake will automatically be released and
the vehicLe will start moving. Important: The
driver's door must be closed.
Stopping/parking the car
If
you
open the driver's door while the selector
lever is not in position P, the vehicle can roll
away. The message Shift to P, otherwise vehicle
can roll away. Doors do not lock if lever is not in
P. appears on vehicles with convenience key*. A
buzzer will also sound.

•
Press and hold the brake pedal
<=>
A..

•
Apply the parking brake.

•
Move the selector Lever to P.
In some situations (such as on mountain roads or
when towing a trailer or caravan) it can be advan­
tageous to switch temporarily to the manual
shift programme so that the gear ratios can be
selected manually to suit the driving conditions

^>page
90.
On level ground it is sufficient to move the selec­
tor lever to P. On a gradient the parking brake
should be applied first and the selector Lever
should be moved to
P ^>page
82. This reduces
the load on the locking mechanism and makes it
easier to move the selector lever out of position
P. •
88

Driving
A WARNING
- The driver should never get out of the
vehi­

cle when the engine is running and a gear is

engaged.
If you have to leave your vehicle
while the engine is running, you must apply
the parking brake and engage the parking
lock P.
-If the engine is running and a gear is engag­
ed (D/S or R) or the vehicle is in "tiptronic"

mode,
you will need to hold the car with the
footbrake. Otherwise, the car will "creep"
forwards as the power transmission is not
fully interrupted even when the engine is

idling.

- The accelerator pedal must on no account
be pressed inadvertently when the vehicle is
stationary. The vehicle could otherwise start
moving immediately (in some cases even if
the parking brake is engaged) and possibly
cause an accident.
- Do not press the accelerator while selecting
a gear with the vehicle stationary and the
engine running, as this could cause an
acci­

dent.
- Never move the selector lever to R or P
when driving at normal speeds, as this could
cause an accident.
- Before you drive down a steep gradient, re­
duce the speed and use "tiptronic" to select
a low gear.
- Never allow the brake to drag when driving
downhill and do not use the brake pedal too
often
or
for long periods. Constant braking
will cause the brakes to overheat and will
considerably reduce the effectiveness of the
brakes. It will increase the braking distance
and could cause the brake system to
fail.

- To avoid rolling back on gradients always
hold the vehicLe with the footbrake or park­
ing brake if you have to stop.
- Never attempt to hold the vehicle with the
clutch when stopping on a gradient. The
clutch is disengaged automatically if it is
overloaded and becomes too hot - accident
risk! If the clutch is overloaded, the indica­
tor lamp
0
will light up and a message will
appear
^>page
92.
© CAUTION
- When you have stopped on a gradient, do
not try to stop the vehicle rolling back by ac­
celerating when a gear is engaged. This
could cause the automatic gearbox to over­
heat and become damaged. Apply the park­
ing brake or press the brake pedal in order
to prevent the vehicle from rolling back.
- If you allow the car to roll with the selector
lever in position N with the engine switched
off, the automatic gearbox will be damaged
as it will not be lubricated
^page
328,
Tow-starting / towing
away.

- In certain driving and traffic conditions, for
instance in stop-and-go traffic, if you have
to pull away frequently or if the vehicle
creeps forwards over a long distance, the
gearbox can overheat and become dam­

aged.
If the indicator Lamp
[5J
or the warn­
ing
lampH
Lights up, stop the vehicle at
the first opportunity and let the gearbox
cool down
^>page
92.
© Note
For safety reasons the parking brake will only
release automatically if the driver's door is

closed.

Downhill speed control
Applies to: vehicles with automatic gearbox
The downhill speed control function helps the
driver when driving down steep gradients.
Downhill speed control is activated on a downhill
gradient when the selector lever is in D/S and the
driver presses the brake pedal. The gearbox auto­
matically selects a suitable gear for the gradient.
The downhill speed control function attempts to
maintain the speed at which the vehicLe was trav­
elling when the foot brake was applied (subject
to the laws of physics and technical limitations of
the power train). It may be necessary to adjust
the speed again using the foot brake. The down­
hill speed control can change down to 3rd gear
but no further, so it may be necessary to change
to tiptronic mode on very steep gradients. In this

case,
change down manually to 2nd or 1st gear in •
CO
89

Intelligent technology

CO

< o rN
iv
rN
t-H
o < 00
event of faults or anomalies in the vehicLe data,
only these data are saved. As a rule, faults are
shown by the warning lamps in the instrument
cluster.
Data saved in the control units can only be read
and analysed with special equipment.
A qualified workshop is only able to recognise
and deal with faults by using the relevant saved

data.
Among other things, the saved data may
contain the following information:
- Data relating to the engine and the gearbox
-Speed
- Direction of travel
- Braking force
- Seat belt warning system data
The control units installed will not under any cir­
cumstances record conversations in the vehicle.
Event data recorder
Your vehicLe is not equipped with an event data
recorder.
In an event data recorder, information about the
vehicle is temporarily saved. In the event of an
accident, you can therefore obtain detaiLed infor­
mation about the course of events. On vehicles
with an airbag system, accident-related data
such as impact speed, seat belt status, seat
posi­

tions and trigger times can be saved. The exact
information saved depends on the manufacturer.
The installation of an event data recorder is sub­
ject to the agreement of the vehicle's owner. This
process is governed by legislation in some coun­

tries.

Reprogramming control units
All data for controlling components are saved in
the control units. Some convenience features,
such as one-touch signalling, single door unlock­
ing and display messages can be reprogrammed
using special workshop equipment. If any
con­

venience features are reprogrammed, the infor­
mation in this Owner's Manual will no longer be
accurate for the features that have been

changed.
We recommend having the reprogram­
ming approved.
Your Audi dealer will be able to provide you with
information about possibLe reprogramming op­

tions.

Event memory
There is a diagnostic connection for reading out
the event memory Located in the
footweLL
on the
driver's side of the vehicle. Information regard­
ing the operation and status of the vehicle's elec­
tronic control units is stored in the event memo­
ry. The event memory should only be read out
and erased by
a
qualified workshop.
A WARNING
The diagnostic connection must not be used
for other purposes. Incorrect use can cause
malfunctions - risk of accident!
151