2021 AUDI Q2 ESP

Wheels

WheeLs

Tyres and rims
General notes

•
Inspect the tyres regularly for damage (cuts,
cracks or blisters, etc.). Remove any foreign
bodies embedded in the treads.

•
If
you
have to drive over
a
kerb or similar obsta­

cle,
drive very slowly and as near as possible at
a right angle to the kerb.
• Damaged rims or tyres must be replaced imme­
diately.

•
Keep grease, oil and fuel off the tyres.

•
Mark the wheels before taking them off so that
they rotate in the same direction when refitted.

•
When removed, the wheels should be stored
flat in a
cool,
dry and preferably dark place.

CO

<
O
rN
IV
rN
t-H
o <

(l)
CAUTION
- Please note that summer and winter tyres
are optimised for the prevailing road condi­
tions at different times of
year.
We recom­
mend that you use winter tyres during the
winter months. At low temperatures, sum­
mer tyres lose their elasticity and grip, and
braking performance also suffers as a re­
sult. Cracks can form in the tread block on
summer tyres if they are used at very cold
temperatures, and this can cause perma­
nent damage to the tyres. An increase in
rolling noise and tyre imbalance may result
from this damage.
- Machined, polished or chrome-plated rims
must not be used in winter conditions. The
process used to manufacture these types of
wheel rim does not provide adequate sur­
face protection against corrosion, and the
rims can be permanently damaged by road
salt or similar.
New wheels or tyres
It is best to have all servicing of wheels and tyres
performed by a qualified workshop, since they
have the necessary special tools and replacement
parts in addition to trained personnel.

•
New tyres do not yet give maximum grip. When
driving with new tyres, drive at moderate
speeds and be especially careful during the first
500 km.

•
All four wheels must be fitted with tyres of the
same type, size (rolling circumference) and
preferably the same tread pattern.
• Tyres should be replaced in pairs and not
indi­

vidually (i.e. both front tyres or both rear tyres
together).

•
We recommend the use of Audi Genuine Tyres.
If
you
wish to use other tyres, please note that
the actual size can differ from the nominal size
marked on the tyre
•=> /\.
•
If
you
wish to purchase a different combination
of rims and tyres than the ones fitted on the ve­
hicle during production, it is advisable to
con­

sult
a
qualified workshop beforehand
<=> /\.

The sizes of the rims and tyres approved
for
your
vehicle are listed in the vehicle's documents (e.g.

EC
Certificate of Conformity or COC
document1)).

The vehicle documents vary depending on the
country in which the vehicle is registered.
If the spare wheel* is
not
the same type as the
tyres fitted on the car (for example if the car has
winter tyres or wide-section tyres) you should on­
ly use the spare wheel* if
a
puncture occurs, and
then
only
for
a
short period of time. In this case,
please drive with extra care. Refit
a
normal road
wheel as soon as possible.
Applies to vehicles with four-wheel drive: All four
wheels must always be fitted with tyres of the
same type, make and tread pattern, as the drive-
line could otherwise be damaged by variations in
the wheel speeds. For the same reason, only use
a spare wheel* which has the same rolling cir­
cumference as the normal road wheels.
Manufacturing date
The manufacturing date is indicated on the tyre
sidewall (possibly only on the inner side of the
wheel): •

15 COC
= Certificate of conformity
305

Wheels
more tyres, the driver is alerted by an indicator
lamp
0H ar|d a
message in the instrument cluster
display. If only one tyre is affected, the display
will indicate its position.
Each time you change a tyre, change the wheels
round or change the tyre pressures on your
vehi­

cle (e.g. when switching from partial load to full
load and vice-versa), you must store the new tyre
pressures in the menu display
<=>page
311.
Mon­

itoring of the tyre pressures is based on the tyre
pressures you have stored. The inflation pres­
sures recommended for your vehicle are given on
the tyre pressure sticker
opage
307, Fig. 253.
The rolling circumference and vibration can
change and cause a tyre pressure warning if:
- The inflation pressure in one or more tyres is
too low.
- The tyre has suffered structural damage.
- The wheels were changed or the tyre pressures
were changed and the new tyre pressures were
not stored
<>page
311.
- The vehicLe load is not balanced (more load on
one side).
- There is more load on the wheels of one of the
axles (e.g. when towing a trailer or driving up
or down a gradient).
- You are driving with snow chains.
- You are driving with the temporary spare

wheel*.

- Only one wheel of an axle has been changed.
Indicator lamps
flfl - Loss of pressure on one or more tyres
o
A-
Check and change or repair the tyre(s). Check and
adjust the tyre pressures again on all four
wheels. Then store the tyre pressures in the
menu dispLay
opage
311.

IIJ'f.1
(Tyre pressure loss indicator) Tyre pressure:
System fault!.
If llil'f>1
appears and the indicator

LampBH in the
instrument cluster dispLay flashes
for approx. one minute and then remains lit after
you have switched on the ignition or while you
are driving, there is a fault in the system. Check
and adjust the tyre pressures for all four tyres
and store the
new
tyre pressures
•=>page
311. If
the indicator lamp does not go out or if it comes
on again after
a
short time, drive to a qualified
workshop without delay and have the fault
recti­

fied.

®
No
- If
a
malfunction occurs in the ESC/ABS sys­

tem,
the tyre pressure loss indicator may al­
so be out of action.
-When driving with snow chains, a system
malfunction can occur.
-The tyre pressure Loss indicator on your Audi
is specially matched to "Audi Genuine Tyres"

^>page
305. We recommend that you use
these tyres.
- The tyre pressure Loss indicator can only
monitor the pressures of the tyres fitted on
the car. For this reason please regularly
check the tyre pressure of the spare wheel
in the luggage compartment so it can be
used if required.

A
WARNING
- If the tyre pressure loss indicator appears in
the instrument cluster display, slow down
immediately and avoid any severe braking or
steering manoeuvres. As soon as you can do
so safely, stop and check the tyres and the
tyre pressures.
- It is the driver's responsibility to ensure that
the tyre pressures are correct. For this rea­
son you must check the tyre pressures
regu­

larly.
- Under certain conditions (e.g. driving at
high speeds, on ice and snow or on poor
road surfaces) the tyre pressure loss indica­
tor may not appear immediately.
- The use of run-flat tyres on your vehicLe is
NOT authorised! Unauthorised use can cause
an accident or damage your vehicle.
310

Care of vehicle and cleaning
Care of vehicLe and
cleaning
General notes
Regular and careful care helps to maintain the
value of the vehicLe. This may also be one of the
requirements for upholding any warranty claims
in the event of corrosion or paint defects.
Qualified workshops carry stocks of suitable car
care products. PLease
foLLow
the instructions for
use on the packaging.
A WARNING
- Cleaning products and other materials used
for car care can damage health if misused.
- Car care products can contain toxic substan­
ces and must always be kept in a safe place
out of reach of children.

+) For
the sake of the environment
- Please choose care products that are not
harmful to the environment.
- Surplus cleaning materials should not be
disposed of together with ordinary house­
hold waste.
Washing the vehicle
The longer residues like insects, bird droppings,
resinous tree sap or road salt are alLowed to re­
main on the vehicle, the more damage they can
do to the paintwork. High temperatures (for in­
stance in direct sunlight) further intensify the
damage.
Before washing, soak heavy dirt with plenty of
water.
Stubborn dirt, such as bird droppings or resinous
tree sap, is best removed with plenty of water
and a micro-fibre cloth.
After the period when salt is put on the roads,
have the underside of the vehicLe washed thor­
oughly.
High-pressure cleaners
When cleaning the vehicle with a high-pressure
cleaner, always follow the operating instructions
for the equipment. This applies particularly to
the operating pressure and the spraying dis­

tance.
Do not point the spray jet directly at the
seals on the windows, doors, boot lid, bonnet or
panorama sun roof*, or at the tyres, rubber ho­

ses,
insulating material, sensors* or camera
len­

ses*.
Maintain a distance of at least 40 cm.
Do not use a high-pressure cleaner to remove
snow and ice.
Never use high-pressure cleaners with a round-
jet nozzle or "dirt blasters".
The water must not be hotter than 60 °C.
Automatic car washes
Spray the vehicle with water before washing.
Ensure that the windows and panorama sun roof*
are closed and that the windscreen wipers are
switched off. Follow the car wash operator's rules
and recommendations, especially if any accesso­
ries are attached to your vehicle.
If possibLe use a brushless car wash.
Washing by hand
Clean the car with a soft sponge or brush, start­
ing on the roof and working down. Use solvent-
free cleaning agents.
Washing matt-painted vehicles by hand
To avoid damaging the paintwork when washing
the car, first remove any dust, sand and grit. In­

sects,
grease stains and fingerprints are best re­
moved using a special cleaning agent for matt-
painted surfaces.
Apply the product with a micro-fibre cloth. Do
not apply too much pressure to avoid damaging
the paintwork.
Rinse the car thoroughly with water. Then clean
the car with a neutral shampoo and a soft micro-
fibre cloth.
Rinse the car with lots of water again and then
let it dry in the air. Remove any water stains with
a chamois. •
312

Care of vehicle and cleaning
Component(s)
Paintwork
Carbon parts
Decals
Situation
Paint damage
Fuel overflow
Surface rust
Corrosion
Water no longer
pearls off clean paint­
work
Paint has Lost its

shine,
gloss cannot
be restored by waxing
Residues, e.g. in­

sects,
bird droppings,
resinous tree sap,
road salt
Fat-based stains, e.g.
cosmetics
or
sun lo­
tion
Dirt/deposits
Dirt/deposits
Remedy
Refer to the vehicle data sticker for the paint no. and touch
up using a paint pen
^>page
342
Rinse with water without delay
Surface rust remover, apply wax afterwards; contact your
qualified workshop with any questions
Have it removed by your qualified workshop
Apply wax (at least twice a year)
Treat with a suitable polish; finish with wax coating if
pol­

ish does not contain wax compounds
Remove immediately using water and a micro-fibre cloth
Remove immediately using
miLd
detergent3'
and a soft
cloth
Same treatment as painted parts
^page
312
Soft sponge with mild
detergent3'

a)
Mild detergent: not more than two tablespoons of
pH-neutral
detergent to one litre of water
Cleaning the interior
Component(s)
Windows
Ornamental trim/
mouldings
Plastic parts
Displays/instru­
ment cluster
Controls and dis­
plays
Seat belts
Situation
Dirt/deposits
Dirt/deposits
Dirt/deposits
Heavier dirt/deposits
Dirt/deposits
Dirt/deposits
Dirt/deposits
Remedy
Glass cleaning agent, then wipe dry
Mild
detergent3'

Damp cloth
Mild
detergent3';
solvent-free plastic cleaning agent if nec­
essary
Soft cloth with LCD cleaner
Soft brush, then soft sponge with mild detergent3'
Mild detergent3' (allow to dry before retracting)
314

Care of vehicLe and cleaning

CO

<
O
rN
r>
rN
•-i

00
Component(s)
Fabrics,
leatherette,
Alcantara
Natural leather
Carbon parts
Situation
Surface dirt
Water-based stains,

e.g.
coffee, tea,

blood,
etc.
Fat-based stains, e.g.

oil,
make-up, etc.
Special dirt/stains,

e.g.
ballpoint pen,
nail varnish, disper­
sion paint, shoe

cream,
etc.
Fresh dirt/stains
Water-based stains,

e.g.
coffee, tea,

blood,
etc.
Fat-based stains, e.g.

oil,
make-up, etc.
Special dirt/stains,

e.g.
ballpoint pen,
nail varnish, disper­
sion paint, shoe

cream,
etc.
Care of vehicle
Dirt/deposits
Remedy
Vacuum cleaner
Absorbent cloth and mild
detergent3'

Apply mild detergent3', dab off dissolved grease or colour
particles with absorbent cloth; if necessary treat with wa­
ter
Special stain remover (dab off with absorbent fabric); if
necessary treat with mild
detergent3'

Cotton cloth with mild
detergent3'

Fresh stains: absorbent cloth
Dried stains: stain remover suitable for leather
Fresh stains: absorbent cloth and suitable stain remover
for leather
Dried stains: grease removal spray
Stain remover suitable for leather
Regularly apply leather-care cream with ultra-violet pro­
tection and impregnating compound; if necessary use spe­
cial colour leather cream
Same treatment as plastic parts

a^
Mild detergent: not more than two tablespoons of pH-neutral
A WARNING
Do not use water-repellent coatings on the
windscreen. In bad visibility conditions such
as Light
rain,
Low sun or when driving at night
these coatings can cause increased dazzle,
which is a serious safety hazard. Such coat­
ings can also cause the wiper blades to
jud­

der.
© CAUTION
-
Headlights/rear
lights
- Never clean the headlights/rear lights
with a dry cloth or sponge.
detergent to one litre of water
- Do not use cleaning agents containing al­

cohol.
This could cause the glass to crack!
- Wheels
- Do not use paint polish or other abrasive
agents.
- If the protective paint coating on the
wheel rim is scratched or damaged by
stone chips etc., the damaged area should
be touched up without delay.
-Sensors/camera lenses
- Never remove snow and ice from the cam­
era lens using warm or hot water - danger
of cracks appearing on the lens.
315

Mobility
7. Connect one end of the black lead preferably
to the earth point or alternatively to the
neg­

ative battery terminal © on the vehicle pro­
viding assistance®.
8. Connect the other end of the
black
jump lead
only to the earth point © of the jump-start
connection on your vehicle ©
<=>(£).

9. Position the jump leads in such a way that
they cannot come into contact with any mov­
ing parts in the engine compartment.
Starting the engine

10.
Start the engine of the vehicle with the
boosting battery and let it run at idling

speed.

11.
Start the engine of the
car
with the dis­
charged battery and wait two or three mi­
nutes until the engine is running smoothly.

12.
If the engine fails to start: do not operate the
starter for longer than 10 seconds. Wait for
about 30 seconds and try again.

13.
Switch on the blower and the rear window
heating on the vehicle which has been jump-
started in order to offset excessive voltage
which may occur when disconnecting the

leads.
The headlights must be switched off!

14.
Disconnect the leads in exactly the opposite
sequence to that described in
*page
327
with the engines running. Make sure that the
Leads cannot come into contact with any
moving parts in the engine compartment.

15.
Fold the cover back onto the battery in its
correct position.

16.
Switch off the blower and the rear window
heating again.
PLease refer to
<=>
A in Before starting the engine
on page 326 and
•=>©
in Before starting the en­
gine on page 327.
© CAUTION
Do not use the negative battery terminal
when jump-starting (this could cause a
mal­

function in the on-board electrical system).
- Connect the battery clamps so they have
good metal-to-metal contact with the bat­
tery terminals.
- The vehicle battery is vented to the outside
to prevent gases entering the vehicle's inte­
rior.

Tow-
start
ing / towing
away
General notes
Some experience is required to tow or tow-start a
vehicle, especially when using a tow-rope. Both
drivers should be familiar with the technique re­
quired for towing. Inexperienced drivers should
not attempt to tow-start or tow away another ve­

hicle.

Do not pull too hard with the towing vehicle and
take care to avoid jerking the tow-rope. When
towing off-road, there is aLways a risk that the
anchorage points may be overloaded.
Tow-bar / tow-rope
It is easier and safer to tow the vehicle with a
tow-bar. You should only use a tow-rope if you do
not have a tow-bar. It is advisable to use a tow-
rope made of elastic synthetic fibre or similarly
elastic material.
Notes on towing vehicles
The vehicle can be towed with a tow-bar or tow-

rope.
When the engine is not running, the
gear­

box will not be adequately lubricated if the
fol­

lowing speed/distance restrictions are not ob­

served:

- The vehicle must not be towed faster than
50 km/h.
- The vehicle must not be towed further than
50 km. •
328

Fuses and bulbs

CO

rN
IV
rN
•-i

00
- Make sure that the covers are correctly seat­
ed on the headlights and the rear lights.
This will ensure that water cannot enter the
housings and cause the lights to malfunc­

tion.

- Do not touch the glass part of the bulb with
your bare hands; use a cloth or paper towel

instead.
Otherwise, the fingerprints left on
the glass will vaporise as a result of the heat
generated by the bulb, be deposited on the
reflector and impair its surface.
© CAUTION
When removing or installing the rear light,
take care not to cause any damage.
- Removing the rear light in particular can
lead to the paintwork or rear light becoming

damaged.
This is another reason why we
recommend having the bulbs changed by a
qualified workshop.
- Never use metal tools (e.g. a screwdriver) or
sharp or pointed plastic tools to lever out
the rear light - risk of damaging the paint.
- Make sure you have a soft cloth ready to
place under the glass on the rear light, to
avoid any scratches.
® For the sake of the environment
A qualified workshop can advise you how to
dispose of used bulbs in the proper manner.
© Note
- Please check at regular intervals that
alL

lighting (especially the exterior Lighting) on
your vehicle is functioning properly. This is
not only in the interest of your own safety,
but also in that of all other road users.
- Before changing a bulb, make sure you have
the correct new bulb.
Bulbs at front of vehicle
Applies to: vehicles with halogen headlights

Fig.
279 Halogen headlights: Overview of left side of
vehi­

cle
You must only replace a bulb with a bulb of the
same type. Information regarding e.g. the wat­
tage can be found on the base of the bulb.
The description for changing the bulb refers to
the left headlight; the procedure for the right
headlight is similar.
Halogen headlights
The following bulbs can be changed:
Bulb (12 V)

(T)Main
beam headlight
© Dipped headlight
© Daytime running light
© Turn signal
Version

H7LL(55
W)

H7LL(55W)

PW24W
PWY24W
Bulbs at rear of vehicle
Applies to: vehicles with bulbs

Fig.
280
Rear
of
vehicle:
Bulbs on
leftside
of vehicle
335

Accessories
and
modifications
to the
vehicle
Accessories
and
modifi­
cations
to the
vehicle
Accessories,
replacement parts
and

repairs
Always
ask
your dealer
or
specialist retailer
for

advice before purchasing accessories
and
re­
placement parts.
Your
car is
designed
to
offer
a
high standard
of

active and passive safety. For this reason,
we
rec­
ommend that you ask your Audi dealer
for
advice
before fitting accessories
or
replacement parts.
Audi dealers have
the
latest information from
the manufacturer and
can
recommend accesso­
ries and replacement parts which
are
suitable
for

your requirements. They can also answer
any

questions you might have regarding official
regu­

lations.
We recommend you
to
use only Audi accessories
and Audi Genuine Parts. Audi has tested these
products
for
suitability, reliability and safety.
Audi dealers have
the
necessary experience
and

facilities
to
ensure that
the
parts
are
installed
properly.
Although
the
market
is
constantly scrutinised,
Audi
cannot
judge
or
assume responsibility
for

the reliability, safety and suitability
of
non-genu­
ine products
-
even though
in
some instances,
these parts
may
have been approved
by
an
offi­

cially recognised technical testing authority
or

accompanied
by
an official approval certificate.
Any retro-fitted equipment which has a direct
ef­

fect on
the
vehicle and/or
the
way
it is
driven

(e.g.
cruise control system
or
electronically-con­
trolled suspension) must
be
approved
for
use
in

your vehicle and bear
the e
mark
(the
European
Union's approval symbol).
If any additional electrical components are fit­
ted which
do not
serve
to
controL
the
vehicLe
it­

self
(for
instance a refrigerator box, laptop
or

ventilator
fan,
etc.), these must bear the C€ mark
(manufacturer conformity declaration
in the Eu­

ropean Union).

A,
WARNING

Never attach accessories (such
as cup
holders
or telephone brackets)
to the
surfaces cover­
ing
the
airbag units
or the
areas around
the

airbags: this could cause injury
if
the airbag
is

triggered.

Modifications
Modifications must always
be
carried
out
accord­
ing
to our
specifications.
Unauthorised modifications
to the
electronic
components, software, wiring
or
data transfer
in

the vehicLe may cause malfunctioning. Due
to the

way
the
electronic components
are
linked togeth­
er
in
networks, other systems
may be
affected
by

the faults. This can seriously impair safety, lead
to excessive wear
of
components,
and
also inva­
lidate
the
type approval
for
your vehicle.
You will appreciate that your Audi dealer cannot
be held liable
for
any damage caused
by
modifi­
cations and/or work performed incorrectly.
We recommend that
all
work should
be
per­
formed
by
an Audi workshop using Audi Genuine

Parts.

/K
WARNING

- Incorrectly performed modifications
or
oth­

er work
on
your vehicLe can lead
to
malfunc­
tions and cause accidents.
-
Do not
use an additional
or
replacement
number plate holder other than
the
original
one fitted
at the
front
of
the vehicle.
Radio transmitters
and

business equipment
Transmitters
An external aerial
is
required
in
order
to
operate
radio equipment inside
the
vehicle. The maxi­
mum range
of
the equipment can only
be
ach­

ieved with
an
external aerial.
Retrofit installations
of
radio transmitters
in the

vehicle
are
subject
to
official approval and can
af­

fect
the
type approval
for
your vehicle.
In •

340