2020 MAZDA MODEL CX-30 brake

NOTE
Under the following conditions,
the KEY warning indication (red)
is displayed after the push button
start is pressed. This informs the
driver that the push button start
will not switch to ACC, even if it
is pressed from off (page 7-28).
The key battery is dead.The key is out of operational
range.
The key is placed in areas where
it is difficult for the system to
detect the signal (page 3-7).
A key from another
manufacturer similar to the key
is in the operational range.
(Forced engine starting method)
If the KEY warning indication
(red) is displayed, or the push
button start indicator light
(amber) flashes, this could
indicate that the engine may not
start using the usual starting
method (page 7-28). Have your
vehicle inspected at an
Authorized Mazda Dealer as
soon as possible. If this occurs,
the engine can be force-started.
Press and hold the push button
start until the engine starts. Other
procedures necessary for starting
the engine, such as having the key
in the cabin, and depressing the
clutch pedal (manual
transmission) or the brake pedal
(automatic transmission) are
required.
When the engine is force-started,
the KEY warning indication (red)
remains displayed and the push
button start indicator light
(amber) remains flashing.
(Automatic transmission)
When the selector lever is in the
neutral (N) position, the push
button start indicator light (green)
does not turn on.
7. Press the push button start after the push button start indicator light
(green) turns on.
NOTE
After starting the engine, the push
button start indicator light
(amber) turns off and the ignition
switches to the ON position.
After pressing the push button
start and before the engine starts,
the operation sound of the fuel
pump motor from near the fuel
tank can be heard, however, this
does not indicate a malfunction.
8. After starting the engine, let it idle for about 10 seconds.
NOTE
Whether the engine is cold or
warm, it should be started
without the use of the
accelerator.
If the engine does not start the
first time, refer to Starting a
Flooded Engine under Emergency
Starting. If the engine still does
not start, have your vehicle
inspected by an Authorized
Mazda Dealer (page 7-16).
▼ Engine Start Function When Key
Battery is Dead
CAUTION
When starting the engine by holding
the transmitter over the push button
start due to a dead key battery or a
malfunctioning key, be careful not to
allow the following, otherwise the
signal from the key will not be received
correctly and the engine may not start.
When Driving
Start/Stop Engine
4-7
CX-30_8HG6-EA-19I_Edition1_new
2019-6-13 18:45:11

Metal parts of other keys or metal
objects touch the key.
Spare keys or keys for other vehicles
equipped with an immobilizer
system touch or come near the key.
Devices for electronic purchases, or
security passage touch or come near
the key.
If the engine cannot be started due to
a dead key battery, the engine can be
started using the following procedure:
1. Continue to depress the brake pedal firmly until the engine has
completely started.
2. (Manual transmission)
Continue to depress the clutch
pedal firmly until the engine has
completely started.
(Automatic transmission)
Put the vehicle in park (P). If you
must restart the engine while the
vehicle is moving, shift into neutral
(N).
3. Make sure that the push button start indication light (green) flashes.
4. Align the center area of the emblem on the transmitter with the
center area of the push button start
while the push button start
indicator light (green) flashes.

1. Indicator light
2. Push button start
3. Transmitter
4. Emblem

5. Make sure that the push button start indicator light (green) turns
on.
6. Press the push button start to start
the engine.
NOTE
The engine cannot be started
unless the clutch pedal is fully
depressed (manual transmission)
or the brake pedal is fully
depressed (automatic
transmission).
If there is a malfunction with the
push button start function, the
push button start indicator light
(amber) flashes. In this case, the
engine may start, however, have
the vehicle checked at an
Authorized Mazda Dealer as
soon as possible.
If the push button start indicator
light (green) does not illuminate,
perform the operation from the
beginning again. If it does not
illuminate, have the vehicle
checked at an Authorized Mazda
Dealer.
When Driving
Start/Stop Engine
4-8
CX-30_8HG6-EA-19I_Edition1_new 2019-6-13 18:45:11

To switch the ignition position
without starting the engine,
perform the following operations
after the push button start
indicator light (green) turns on.
1. Release the clutch pedal(manual transmission) or
brake pedal (automatic
transmission).
2. Press the push button start to switch the ignition position.
The ignition switches in the
order of ACC, ON, and off
each time the push button
start is pressed. To switch the
ignition position again,
perform the operation from
the beginning.
▼Emergency Operation for Starting
the Engine
If the KEY warning indication (red) is
displayed, or the push button start
indicator light (amber) flashes, this
could indicate that the engine may not
start using the usual starting method.
Have your vehicle inspected at an
Authorized Mazda Dealer as soon as
possible. If this occurs, the engine can
be force-started. Press and hold the
push button start until the engine
starts. Other procedures necessary for
starting the engine such as having the
key in the cabin, and depressing the
clutch pedal (manual transmission) or
the brake pedal (automatic
transmission) are required.
Turning the Engine Off
▼Turning the Engine
Off
WARNING
Do not stop the engine while the
vehicle is moving:
Stopping the engine while the vehicle
is moving for any reason other than in
an emergency is dangerous. Stopping
the engine while the vehicle is moving
will result in reduced braking ability
due to the loss of power braking,
which could cause an accident and
serious injury.
1. Stop the vehicle completely.
2.(Manual transmission)
Shift into neutral and set the
parking brake.
(Automatic transmission)
Shift the selector lever to the P
position and set the parking brake.
3. Press the push button start to turn off the engine. The ignition position
is off.
CAUTION
When leaving the vehicle, make sure
the push button start is off.
NOTE
The cooling fan in the engine
compartment could turn on for a few
minutes after the ignition is switched
from ON to OFF, whether or not the
A/C is on or off, to cool the engine
compartment quickly.
If the system detects that the
remaining battery power of the key is
low when the ignition is switched
from ON to ACC or OFF, the
following is indicated.
When Driving
Start/Stop Engine
4-9
CX-30_8HG6-EA-19I_Edition1_new 2019-6-13 18:45:11

distance on the trip meter and the total
fuel consumption, and the average fuel
economy for either drive information
display is displayed.
The average fuel economy is also
displayed by a red arrow in the
instantaneous fuel economy display.

The average fuel economy and trip
meters can be reset by pressing the
INFO switch for 1.5 seconds or more
while in each mode. After the data is
cleared, the fuel consumption is
recalculated and the - - - L/100 km
(- - - mpg) for the 1 minute prior to it
being displayed is indicated.
▼Current Fuel Economy
This displays the current fuel economy
by calculating the amount of fuel
consumption and the distance
traveled.

NOTE
Indicates the 0 position when the
vehicle speed is about 5 km/h (3
mph) or slower.
The red arrow on the scale indicates
the average fuel economy.
▼
i-ACTIVSENSE Display*
Displays the system status.

Refer to Lane Departure Warning
System (LDWS) on page 4-91.
Refer to Blind Spot Monitoring
(BSM) on page 4-95.
Refer to Traffic Sign Recognition
System (TSR) on page 4-99.
Refer to Distance & Speed Alert
(DSA) on page 4-104.
Refer to Driver Attention Alert (DAA)
on page 4-105.
Refer to Driver Monitoring (DM) on
page 4-107.
Refer to Front Cross Traffic Alert
(FCTA) on page 4-108.
Refer to Mazda Radar Cruise Control
(MRCC) on page 4-116.
Refer to Mazda Radar Cruise Control
with Stop & Go function (MRCC
with Stop & Go function) on page
4-124.
Refer to
Tra ffi c Jam Assist (TJA) on
page 4-136.
Refer to Lane-keep Assist System
(LAS) on page 4-148.
Refer to Smart Brake Support (SBS)
on page 4-151.
Refer to Smart Brake Support [Rear]
(SBS-R) on page 4-154.
Refer to Smart Brake Support [Rear
Crossing] (SBS-RC) on page 4-158.
When Driving
Instrument Cluster and Display
*Some models.4-19
CX-30_8HG6-EA-19I_Edition1_new
2019-6-13 18:45:11

▼Warning Indication/Warning Lights
These lights turn on or flash to notify th
e user of the system operation status or a
system malfunction.
Signal Warning Refer to
Brake System Warning Indication/Warning Light*17-22
ABS Warning Indication/Warning Light*1
Electronic
Brake Force
Distribution
System Warn- ing
7-23
ABS warning 7-25
Charging System Warning Indication/Warning Light*17-23
Engine Oil Warning Indication/Warning Light*17-23
High Engine Coolant Temperature Warning Indication 7-24
Power Steering Malfunction Indication/Indicator Light*17-24
Master Warning Indication7-25
Brake Control System Warning Indication/Warning Light*17-25
Brake Override Warning Indication7-25
Check Engine Indication/Light*17-26
*Automatic Transmission Warning Indication/Warning Light*17-26
*AWD Warning Indication/Warning Light*17-26
When Driving
Instrument Cluster and Display
*Some models.4-21
CX-30_8HG6-EA-19I_Edition1_new 2019-6-13 18:45:11

SignalIndicator Refer to
Turn Signal/Hazard Warning Indicator Lights Tu r n a n d
Lane-Change Signals
4-47
Hazard Warn- ing Flasher 4-55
Electric Parking Brake (EPB) Indication/Indicator Light*1*27-25
AUTOHOLD Active Indicator Light*14-67
*Mazda Radar Cruise Control with Stop & Go function (MRCC with
Stop & Go function) indicator Light 4-131
*Traffic Jam Assist (TJA) indicator Light
4-144
TCS/DSC Indication/Indicator Light*1
Tra c t i o n C o n -
trol System (TCS)4-72
Dynamic Sta- bility Control (DSC)4-74
Tu r n s o n 7-27
TCS OFF Indicator Light (FWD) *14-72
Off-Road Traction Assist Indicator Light (AWD) *14-75
*Select Mode Indicator Light 4-77
When Driving
Instrument Cluster and Display
4-24*Some models.
CX-30_8HG6-EA-19I_Edition1_new
2019-6-13 18:45:11

SignalIndicator Refer to
(White)
i-ACTIVSENSE Status Symbol (Warning/Risk Avoidance Support Sys-
tem) 4-84
(Green)
(Amber)
i-ACTIVSENSE OFF Symbol (Warning/Risk Avoidance Support Sys-
tem)4-84
(Green)
*High Beam Control System (HBC) Indicator Light
4-88
(White)
*Mazda Radar Cruise Control (MRCC) Standby Indication
4-118
*Mazda Radar Cruise Control with Stop & Go function (MRCC with
Stop & Go function) Standby Indication 4-127
*Tra ffi c
Jam Assist (TJA) Standby Indication 4-138
(Green)
*Mazda Radar Cruise Control (MRCC) Set Indication 4-118
*Mazda Radar Cruise Control with Stop & Go function (MRCC with
Stop & Go function) Set Indication 4-127
*Tra ffi c
Jam Assist (TJA) Set Indication 4-138
*Smart Brake Support (SBS) OFF Indicator Light*1
Smart Brake
Support (SBS)
4-151
Smart Brake
Support [Rear] (SBS-R)4-155
Smart Brake
Support [Rear Crossing]
(SBS-RC) 4-159
(White)
*Cruise Standby Indication 4-201
When Driving
Instrument Cluster and Display
*Some models.4-25
CX-30_8HG6-EA-19I_Edition1_new
2019-6-13 18:45:11

SignalIndicator Refer to
(Green)
*Cruise Set Indication 4-201
*1 The light turns on when the ignition is switched on for an operation check, and
turns off a few seconds later or when the engine is started. If the light does not
turn on or remains turned on, have the vehicle inspected at an Authorized
Mazda Dealer.
*2 The light turns on continuously when the parking brake is applied.
▼ Wrench Indication/Indicator Light
The wrench indication/indicator light
is displayed/turns on under the
following conditions.
When the preset maintenance
period has arrived.
Refer to the Information section in
the Mazda Connect Owner's
Manual.
CAUTION

When the maintenance period
arrives, have your vehicle inspected
by an Authorized Mazda Dealer as
soon as possible. If maintenance is
neglected, a decrease in vehicle
performance may occur which
could cause damage. Have your
vehicle inspected before the
maintenance pe riod arrives.
 If the vehicle continues to be
driven after the engine oil
replacement period has passed, it
could cause damage to the engine.
Replace the engine oil before the
maintenance pe riod arrives.
NOTE
The wrench indication/indicator
light may display/turn on earlier than
the preset period depending on
vehicle usage conditions.
Whenever the engine oil is replaced,
a reset of the vehicle engine control
unit is necessary.
Refer to the Information section in
the Mazda Connect Owner's
Manual.

When Driving
Instrument Cluster and Display
4-26*Some models.
CX-30_8HG6-EA-19I_Edition1_new 2019-6-13 18:45:11