2020 CITROEN DISPATCH SPACETOURER brake

203
1.12 V compressor.
Contains a sealant cartridge for the
temporary repair of a tyre and can also be
used for adjusting tyre pressures.
2. Towing eye.
For more information on To w i n g , refer to
the corresponding section.
Composition of the kit
The tyre inflation pressures are given on
this label. B.
On I/off O switch.
C. Deflation button.
D. Pressure gauge (in bars and psi).
E. Compartment including a cable with an
adapter for a 12
V socket.
F. Sealant cartridge.
G. White pipe with cap for repair and
inflation.
H. Speed limit sticker.
The vehicle's electrical system allows the
connection of the compressor for long
enough to inflate a tyre after a puncture
repair.
Only use the two 12
V sockets, located at
the front , to connect your compressor.
Repair and sealing
procedure
F Park the vehicle without obstructing any
traffic and apply the parking brake.
F

F
ollow the safety instructions (hazard
warning lamps, warning triangle, wearing
high visibility vest, etc.) according to the
legislation in force in the country where you
are driving.
F

S
witch off the ignition.
A. "Sealant"/"Repair" or "Air"/"Inflation"
position selector. F

T
urn the selector A to the
"Repair" position.
F

C
heck that switch B is in
position " O".
Avoid removing any foreign bodies which
have penetrated the tyre.
F

U
ncoil the white pipe G fully.
F

U
nscrew the cap from the white pipe.
F

C
onnect the white pipe to the valve of the
tyre to be repaired.
8
In the event of a breakdown

208
Tyre in the carrier
If you want to change the size of the tyre on the
spare wheel, follow the instructions below.A punctured tyre of size 215 or 225 can be
placed in the carrier.
Removing a wheel
Parking the vehicle
Immobilise the vehicle where it does not
block traffic: the ground must be level,
stable and non-slippery.
With a manual gearbox, engage first gear
then switch off the ignition to block the
wheels.
With an automatic gearbox, place the gear
selector in position

P then switch off the
ignition to block the wheels.
With an electronic gearbox, place the gear
selector in position


A then switch off the
ignition to block the wheels.
Apply the parking brake and check that
the warning lamp is on in the instrument
panel.
The occupants must get out of the vehicle
and wait where they are safe.
Never go underneath a vehicle raised
using a jack
; use an axle stand.
F

E

ngage the carrier on the hook, then tighten
the bolt using the wheelbrace until the bolt
is fully tightened.
Original tyre size XS - M XL
215/65 R16 Placing a
225 wheel in the carrier is prohibited.
There is no restriction.
215/60 R17
215/60 R17 M&S
2 2 5 / 5 5 R17
Placing a
215 wheel
in the
carrier is not
recommended (risk of noise).
F With a steel wheel, remove the bolt cover using tool 3 or the trim by hand.
F

W
ith an alloy wheel, remove the cap from
each of the bolts using tool
3.
F

I
f the vehicle is so equipped, fit security
bolt socket
4 to wheelbrace 1 to slacken the
security bolt.
F

S
lacken (without removing) the other wheel
bolts using just wheelbrace
1.
F

P
lace the foot of the jack on the ground
and ensure that it is directly below jacking
point
A or B provided on the underbody,
whichever is closest to the wheel to be
changed.
In the event of a breakdown

210
F Lower the vehicle again fully.
F F old the jack 2 and detach it.
F

I
f the vehicle is so equipped, tighten the
security bolt using the wheelbrace 1 fitted
with the security socket 4 .
F

T
ighten the other bolts using wheelbrace 1
o n l y.
F

S
tow the tools in the tool box. After changing a wheel
Stow the punctured wheel in the carrier.
Go to a CITROËN dealer or a qualified
workshop as soon as possible.
Have the punctured tyre examined. After
inspection, the technician will advise you
on whether the tyre can be repaired or if it
must be replaced. Fitting a steel or "space-saver" spare
wheel
If your vehicle is fitted with alloy wheels,
when tightening the bolts on fitting it is
normal to notice that the washers do not
come into contact with the steel or "space-
saver" spare wheel. The wheel is secured
by the conical contact of each bolt.
Some driving aid functions should be
disabled, e.g. the Active Safety Brake. If your vehicle has tyre under-inflation
detection, check the tyre pressures and
reinitialise the system.
For more information on Under-inflation
detection
, refer to the corresponding
section.
Tyre under-inflation detection
The steel spare wheel does not have a
sensor.
Wheel with hub cap
When refitting the wheel , refit the hub
cap starting by placing its notch facing the
valve and press around its edge with the
palm of your hand.
In the event of a breakdown

214
For the replacement of these bulbs, contact a
CITROËN dealer or a qualified workshop.
A replacement kit for the LEDs is available from
CITROËN dealers.
Front foglamps
H11- 5 5 W
F Under the front bumper, unscrew the fixing screws of the deflector A , then remove it.F

T
urn the bulb holder a quarter turn anti-
clockwise and remove it.
F
R
eplace the faulty bulb.
To replace this type of bulb, you can also
contact a CITROËN dealer or a qualified
workshop.
Direction indicator side
repeater
- Push the repeater towards the rear and take it out.
-
W

hen refitting, engage the repeater towards
the front and then bring it towards the rear.
Amber coloured bulbs (direction indicators and
side repeaters) must be replaced with bulbs of
identical specification and colour.
Rear lamps
1. Brake lamps/sidelamps (P21/5W-21/5W).
2. Direction indicators (PY21W-21W amber).
3. Reversing lamps (P21W-21W).
4. Foglamps/sidelamps (P21/5W-21/4W).
For vehicles with interior trim, contact a
CITROËN dealer or a qualified workshop
to have the work done.
F

I
dentify the faulty bulb then, depending on
version, open the rear doors or the tailgate.
F

P

ress the locking clip and disconnect the
connector.
In the event of a breakdown

215
F With side-hinged doors, from the outside, unscrew the 2 fixing screws.
F

W
ith a tailgate, from the outside, unclip the
plastic trim then tilt it outwards to remove it.
Next, unscrew the 2 fixing screws.
F

F
rom inside, depending on version, remove
the air vent.
F

W
hile holding the lamp unit in place, press
the clip located on the inner side then
carefully remove the lamp unit.
F

D
isconnect the electrical connector. F
S pread the 3 lugs slightly, then extract the
bulb holder.
F

R
emove the faulty bulb by pressing
lightly on it, then turning it a quarter turn
clockwise.
F

R
eplace the bulb.
Third brake lampW5W-5W
F Depending on version, open the rear left- hand door or the tailgate. F

W
ith side-hinged doors, remove the plastic
cover using a screwdriver.
F
W
ith tailgate, unclip the trim at each end by
turning it upwards, then unclip the central
clips to remove it.
F
W
orking with a screwdriver through the
aperture, push the lamp outwards.
F
D
isconnect the electrical connector and pull
out the lamp.
F
T
urn the bulb holder a quarter turn anti-
clockwise and change the faulty bulb.
To refit, press on the lamp to clip it in place.
8
In the event of a breakdown

216
Number plate lamps
W5W-W
F Insert a thin screwdriver into one of the cut-outs in the lens.
F

P
ush it outwards to unclip it.
F

P
ull out the lens and replace the faulty bulb.
To refit it, press the lens to clip it in.
Courtesy lamps
(front and rear)
LED courtesy lamps
For the replacement of these bulbs, contact a
CITROËN dealer or a qualified workshop.
A replacement kit for the LEDs is available from
CITROËN dealers.
Courtesy lamps with bulb
W5W-5W
To refit, clip the lens in place and ensure that it
is secure.
Platform cab
(rear lamps)
1. Direction indicators (P21W-21W).
2. Brake lamps (P21W-21W ).
3. Sidelamps (R10W-10W).
4. Reversing lamps (P21W-21W).
5. Foglamps (P21W-21W).
F

U

nclip the lens by inserting a thin
screwdriver into the slots at each side of the
courtesy lamp.
F

R

emove the bulb and change it. F

I
dentify the faulty bulb.
F

R
emove the 4 lens unit fixing screws and
remove it.
F

R
emove the faulty bulb by pressing
lightly on it, then turning it a quarter turn
clockwise.
F

C
hange the bulb.
In the event of a breakdown

223
For more information on the Tool box,
refer to the corresponding section.
With a manual gearbox, move the gear
lever into neutral.
With an automatic or electronic gearbox,
place the gear selector in position N .
Failure to adhere to this instruction
may lead to damage to braking system
components and the lack of braking
assistance on restarting the engine.
Towing your vehicle
F Install the towbar.
F S witch on the hazard warning lamps of the
vehicle being towed.
F

M
ove off gently, drive slowly and only for a
short distance.
Towing another vehicle
F In the rear bumper, press on the cover (as shown above) to unclip it.
F

S
crew the towing eye in fully.
F

I
nstall the towbar.
F

S
witch on the hazard warning lamps of the
vehicle being towed.
F

M
ove off gently, drive slowly and only for a
short distance.
F

I

n the front bumper, slide a finger from the
centre of the cover plate to the upper corner
(as shown above) to unclip it.
F

S

crew the towing eye in fully. General recommendations
Obser ve the legislation in force in the
country where you are driving.
Ensure that the weight of the towing
vehicle is higher than that of the towed
vehicle.
The driver must remain at the wheel of
the towed vehicle and must have a valid
driving licence.
When towing a vehicle with all four
wheels on the ground, always use an
approved towing arm
; rope and straps are
prohibited.
The towing vehicle must move off gently.
When the vehicle is towed with its engine
off, there is no longer braking and steering
assistance.
In the following cases, you must always
call on a professional recovery ser vice:
- v ehicle broken down on a motor way or
fast road,
-
f

our-wheel drive vehicle,
-

w
hen it is not possible to put the
gearbox into neutral, unlock the
steering, or release the parking brake,
-

w
hen it is not possible to tow a vehicle
with an automatic gearbox, engine
running,
-

t
owing with only two wheels on the
ground,
-

w
here there is no approved towbar
available.
8
In the event of a breakdown

225
Engines and towed loads - Diesel EURO 4 and 5
EnginesHDi 90 BVM5 HDi 150 BVM6HDi 150 EAT6/
E AT 8 BlueHDi
150
BVM6 BlueHDi
150
E AT 6 / E AT 8
Gearbox Manual
5-speed Manual
6-speed Automatic
6/8-speed Manual
6-speed Automatic
6/8-speed
Code DV6DUDW10F DW10FD
Cubic capacity (cm
3) 1,5 6 01,9 97 1,9 97
Max. power: EC standard (kW) 6611 0 11 0
Fuel DieselDiesel Diesel
Length XS, M,
XL
( L1 / L 2 / L3) M * / X L*
(L2/
L3)* XS, M,
XL
( L1 / L 2 / L3) M * , X L*
(L2/
L3)* XS, M,
XL
( L1 / L 2 / L3) M * , X L*
(L2/
L3)* XS, M,
XL
( L1 / L 2 / L3) M * , X L*
(L2/
L3)* XS, M,
XL
( L1 / L 2 / L3) M * , X L*
(L2/
L3)*
Braked trailer (within the GTW limit) (kg)
on a 10% or 12% gradient 8-9 seats600
1,1 0 0 8001,1 0 0 800
Unbraked trailer (kg) 600750750750750
Maximum authorised nose weight (kg) 2544 3244 32
*
I

ncreased payload.
9
Technical data