2020 CHRYSLER PACIFICA Eco

GETTING TO KNOW YOUR VEHICLE29
release handle is pulled. To select between
“Unlock Driver Door 1st Press” and “Unlock All
Doors 1st Press,” refer to “Uconnect Settings”
in “Multimedia” for further information.
To Lock The Vehicle’s Doors
With one of the vehicle’s key fobs within 5 ft
(1.5 m) of the driver or passenger front door
handle, push the door handle lock button to
lock all four doors and the liftgate.

Push The Door Handle Button To Lock
Do NOT grab the door handle, when pushing the
door handle button. This could unlock the
door(s). Do NOT Grab The Door Handle When Locking

NOTE:
After pushing the door handle button, you
must wait two seconds before you can lock or
unlock the doors, using either Passive Entry
door handle. This is done to allow you to
check if the vehicle is locked by pulling the
door handle, without the vehicle reacting and
unlocking.
The Passive Entry system will not operate if
the key fob battery is depleted.
The vehicle doors can also be locked by using
the key fob lock button, or the lock button
located on the vehicle’s interior door panel.
General Information
The following regulatory statement applies to all
Radio Frequency (RF) devices equipped in this
vehicle:
This device complies with Part 15 of the FCC
Rules and with Innovation, Science and
Economic Development Canada license-exempt
RSS standard(s). Operation is subject to the
following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including interference that may
cause undesired operation.
Le présent appareil est conforme aux CNR
d`Innovation, Science and Economic
Development applicables aux appareils radio
exempts de licence. L'exploitation est autorisée
aux deux conditions suivantes:

1. l'appareil ne doit pas produire de brouillage, et

2. l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d'en compro -
mettre le fonctionnement.
2

20_RU_OM_EN_US_t.book Page 29

GETTING TO KNOW YOUR VEHICLE31
Push the button on the key fob twice
within five seconds to open, close, or
reverse a power sliding door.
The key fob and the overhead console
button will operate the door when the door is
locked. All other ways require the sliding door to
be unlocked. If the vehicle is equipped with
Passive Entry, pressing the button on the
outside handle or Hands-Free feature (if
equipped) will unlock and open the sliding door,
with a valid Passive Entry key fob within 5 ft
(1.5 m) of the door handle.

Overhead Console Power Switches
There are power sliding side door switches
located on the B-Pillar trim panel, just in front of
the power sliding door for the rear seat
passengers.
To operate the sliding door manually with the
handles or to avoid unintentional operation of
the power sliding doors from the rear seats,
push the power sliding door power off button,
located in the overhead console, to remove
power to the handles and buttons just inside
the sliding doors. The power off LED, in the
overhead console, will be lit when the handles
are manual. When the LED is lit, pushing the
power sliding door power off button will return
the handles to power operation.
NOTE:
If anything obstructs the power sliding side
door while it is closing or opening, the door
will automatically reverse to the closed or
open position and an audible tone will sound,
provided it meets sufficient resistance. The
turn signals will flash with sliding door move
-
ments.
If the power sliding door stops in the middle
due to obstacles, it will power open on the
next command.

Driver Side Power Sliding Side Door Switch
Passenger Side Power Sliding Side Door Switch

1 — Liftgate
2 — Right Sliding Door
3 — Sliding Door Power Off
4 — Left Sliding Door
2

20_RU_OM_EN_US_t.book Page 31

34GETTING TO KNOW YOUR VEHICLE
DRIVER MEMORY SETTINGS — IF EQUIPPED
This feature allows the driver to save up to two
different memory profiles for easy recall
through a memory switch. Each memory profile
saves desired position settings for the following
features:
Driver’s seat
Easy Entry/Exit seat operation (on/off) (if
equipped)
Power steering wheel position (if equipped)
Side mirrors (if equipped)
A set of desired radio station presets
NOTE:
Your vehicle is equipped with two key fobs, each
can be linked to either memory position 1 or 2.
The driver memory setting switch is located on
the driver door, next to the door handle, and
consists of three buttons:
The set (S) button, which is used to activate
the memory save function.
The (1) and (2) buttons which are used to
recall either of two saved memory profiles.
Driver Memory Switch

Programming The Memory Feature
To create a new memory profile, perform the
following:
NOTE:
Saving a new memory profile will erase the
selected profile from memory.

1. Place the vehicle’s ignition in the ON/RUN
position (do not start the engine).

2. Adjust all memory profile settings to desired preferences (i.e., driver’s seat, outside
mirrors and radio station presets). 3. Push the set (S) button on the memory
switch, and then push the desired memory
button (1 or 2) within five seconds. The
instrument cluster display will show which
memory position has been set.
NOTE:
Memory profiles can be set without the vehicle
in PARK.
Linking And Unlinking The Key Fob To
Memory
Your key fob can be programmed to recall one
of two saved memory profiles by pushing the
unlock button on the key fob.
NOTE:
Before programming your key fob you must
select the “Personal Settings Linked to Key
Fob” feature through the Uconnect Settings.
Refer to “Uconnect Settings” in “Multimedia”
for further information.
To program your key fob, perform the following:

1. Place the vehicle’s ignition in the OFF position.

2. Select a desired memory profile 1 or 2.
1 — Memory Profile Button 1
2 — Set Button
3 — Memory Profile Button 2

20_RU_OM_EN_US_t.book Page 34

GETTING TO KNOW YOUR VEHICLE35
(Continued)
3. Once the profile has been recalled, push and release the set (S) button on the
memory switch.
4. Push and release button (1) or (2) accordingly. “Memory Profile Set” (1 or 2)
will display in the instrument cluster.
5. Push and release the lock button on the key fob within 10 seconds.
NOTE:
Your key fob can be unlinked to your memory
settings by pushing the set (S) button, and then,
within 10 seconds, pushing the unlock button
on the key fob.
Memory Position Recall
NOTE:
The vehicle speed must be less than or equal to
5 mph (8 km/h) to recall memory positions. If a
recall is attempted when the vehicle speed is
greater than 5 mph (8 km/h), a message will be
displayed in the instrument cluster display. To recall the memory settings for driver one or
two, push the desired memory button (1 or 2) on
the driver's door or the unlock button on the key
fob linked to the desired memory position.
A recall can be cancelled by pushing any of the
memory buttons on the driver's door during a
recall (S, 1, or 2). When a recall is cancelled, the
driver's seat stops moving. A delay of one
second will occur before another recall can be
selected.
NOTE:
Pushing the mirror adjust switch will cancel the
memory mirror recall.
SEATS
Seats are a part of the Occupant Restraint
System of the vehicle.
Manual Adjustment (Front Seats) — If
Equipped
WARNING!
It is dangerous to ride in a cargo area,
inside or outside of a vehicle. In a collision,
people riding in these areas are more likely
to be seriously injured or killed.
Do not allow people to ride in any area of
your vehicle that is not equipped with seats
and seat belts. In a collision, people riding
in these areas are more likely to be seri
-
ously injured or killed.
Be sure everyone in your vehicle is in a seat
and using a seat belt properly.
WARNING!
Adjusting a seat while the vehicle is moving
is dangerous. The sudden movement of the
seat could cause you to lose control. The
seat belt might not be adjusted properly
and you could be injured. Adjust the seat
only while the vehicle is parked.
Do not ride with the seatback reclined so
that the shoulder belt is no longer resting
against your chest. In a collision you could
slide under the seat belt and be seriously or
even fatally injured. Use the recliner only
when the vehicle is parked.
WARNING! (Continued)
2

20_RU_OM_EN_US_t.book Page 35

GETTING TO KNOW YOUR VEHICLE37
Manual Adjustment (Rear Seats) Manual Recline — Quad Seats

Recline Lever

To recline, lean forward slightly, lift the lever,
and push back to the desired position and
release the lever. Lean forward and lift the lever
to return the seatback to its normal position.
Using body pressure, lean forward and rearward
on the seat to be sure the seatback has latched.
Second Row Bench Seat — If Equipped
The second row bench seat can accommodate
two passengers, while providing easy access to
the third row seats without any folding of the
second row seats.
To recline the seatback, lean forward slightly,
lift the recline lever located on the outboard
side of the seat cushion, and push back to the
desired position and release the lever. Lean
forward and lift the lever to return the seatback
to its normal position. Using body pressure, lean
forward and rearward on the seat to be sure the
seatback has latched.

Recline Lever

The bench seat does not stow in the floor, but is
removable for added cargo space.WARNING!
Do not ride with the seatback reclined so that
the shoulder belt is no longer resting against
your chest. In a collision you could slide under
the seat belt, which could result in serious
injury or death.
WARNING!
Adjusting a seat while the vehicle is moving
is dangerous. The sudden movement of the
seat could cause you to lose control. The
seat belt might not be adjusted properly
and you could be injured. Adjust the seat
only while the vehicle is parked.
Do not ride with the seatback reclined so
that the shoulder belt is no longer resting
against your chest. In a collision you could
slide under the seat belt and be seriously or
even fatally injured. Use the recliner only
when the vehicle is parked.
WARNING!
Do not ride with the seatback reclined so that
the shoulder belt is no longer resting against
your chest. In a collision you could slide under
the seat belt, which could result in serious
injury or death.
2

20_RU_OM_EN_US_t.book Page 37

38GETTING TO KNOW YOUR VEHICLE
Removing The Bench Seat

1. Adjust the driver and passenger seats
forward to allow room for the bench seat
removal.

2. Raise the armrest completely, then lift the recline lever located on the outboard side of
the seat to fold the seatback flat against the
seat cushion.

Folded Position
3. Pull the release strap located behind the
seat, in the center near the floor to release
the latches.

Release Strap Location
4. Once the latches are released, tilt the entire
seat toward the front of the vehicle. The
seat can now be removed through either
sliding side door, or through the liftgate.

Tilt Bench Seat Forward

NOTE:
Due to the weight of the bench seat, it is
recommended that two people are utilized
for its removal.
When storing the removed bench seat, it is
important to keep the seatback in the folded
position.

20_RU_OM_EN_US_t.book Page 38

GETTING TO KNOW YOUR VEHICLE39
Reinstalling The Bench Seat

1. To reinstall the bench seat, align the seats
front attachments into the detent positions
on the floor.

2. Tilt seat rearward to lock the seatback into its original position.
NOTE:
Push downward to ensure the rear latches are
in the locked position.
3. Lift the recline handle and return the seatback to the seating position.Second Row Removable 8th Seat — If
Equipped
While the 8th seat does not stow in the floor, it
is foldable and removable for added cargo
space.

Second Row 8th Seat Fold Flat Strap
The release strap is located on the front of the
seat, near the floor. To remove the seat, pull the
release strap to release the rear latches. The
seat assembly can now be removed from the
vehicle by moving it in a rearward direction from
the detent positions in the floor.

Release Strap

WARNING!
If not properly latched, the seat could become
loose. Personal injuries could result.
2

20_RU_OM_EN_US_t.book Page 39

40GETTING TO KNOW YOUR VEHICLE
NOTE:
Seat can be removed easier with one outboard
seat stowed in the load floor.
To reinstall the seat, align the seat into the
detent positions on the floor. Tilt seat rearward
to lock the seatback into its original position.

In Floor Detent Guides
Fold-Flat — Quad Seats
If applicable, refer to the “Hybrid Supplement”
for additional information.
To fold the seat, lift the recliner lever to the full
upward position and push the seatback forward
until it rests on the seat cushion.
Fold-Flat Seat Recline Lever

NOTE:
The seatback may lock into the fold-flat posi -
tion. Use the recline lever to unlock the seat -
back.
When returning the seat to the original posi -
tion, the headrest must be folded back to the
original position.
Fold Headrest To Upward Position

Easy Entry
If applicable, refer to the “Hybrid Supplement”
for additional information.
Easy Tilt Seat — With Or Without Child Seat
Installed
The second row seats can be tilted forward for
easy entry into the third row with or without a
child seat installed.
WARNING!
If not properly latched, the seat could become
loose. Personal injuries could result.

20_RU_OM_EN_US_t.book Page 40