2019 TOYOTA AVALON HYBRID low beam

4
OVERVIEW
Instrument cluster
For details, refer to “Indicators and warning lights,” Section 2, 2019 Owner’s
Manual.
Airbag SRS warning1
Arrow direction indicates fuel
tank door position
Auto Glide Control (AGC)
indicator
Automatic High Beam (AHB)
indicator
Anti-lock Brake System (ABS)
warning1
“AIR BAG ON/OFF” indicator1
Blind Spot Monitor (BSM) indicator
Brake hold operated indicator1,2
BSM w/Rear Cross Traffic Alert
(RCTA) Indicator
BSM outside rear view mirror
indicators
Brake hold standby indicator1
Brake Overrride System/Drive-Start
Control/Intelligent Clearance Sonar
(ICS)
4 warning
Brake system warning
(yellow indicator)1
Brake system warning
(red indicator)1
Charging system warning1
Indicator symbols
Hybrid System Indicator SpeedometerMulti-Information Display
Engine coolant temperature gauge
Outside temperature display Odometer and trip meter display
Shift position and shift range displayFuel gauge
Service indicators and reminders

5
Open door warning
Malfunction/Check Engine indicator1
Master warning1,2
Electric power steering system
warning1
“ECO MODE” indicator
EV drive mode indicator
EV indicator
Low engine oil pressure warning
1
Low Tire Pressure Warning1
Low fuel level warning
Lane Departure Alert (LDA) with
steering control indicator
Pre-Collision System
(PCS) warning1,2
“READY” indicator
Turn signal indicator
Vehicle Stability Control
(VSC) OFF indicator1
Security indicator
SPORT mode indicator
Slip indicator/Hill-start Assist
Control indicator1,3
Constant speed cruise control
indicator/Constant speed
cruise control SET indicator
Full-Speed Dynamic Radar
Cruise Control (DRCC)
indicator/DRCC SET indicator
Headlight low/high beam
indicators
High coolant temperature warning
Intelligent Clearance Sonar
(ICS) OFF indicator1,2,4
Intelligent parking assist
indicator4
Low outside temperature indicatorParking brake indicator
2
Rear passengers’ seat belt
reminder indicatorDriver’s and front passenger’s seat belt
reminder (alarm will sound if speed is
over 12 mph)
Smart Key system indicator
OVERVIEW FEATURES & OPERATIONS TOYOTA SAFETY SENSE SAFETY & EMERGENCY FEATURES
1
If the indicator does not turn off within a few seconds of starting the Hybrid System, there may be a
malfunction. Have the vehicle inspected by your Toyota dealer.
2 If the indicator flashes, there may be a malfunction. Refer to the Owner’s Manual.3 If the indicator flashes, it indicates that the system is operating.4 If equipped.

17
High beam
or
Auto High Beam*
Headlights
Parking lightsHigh beam
flasher
Auto
OFFLow beam
Right turn
Lane change
1
Lane change2
Left turn
1
The right hand signals will flash three times.
2
The left hand signals will flash three times. Daytime Running Light system (DRL) Automatically turns on the headlights at a
reduced intensity.
Automatic light cut off system Automatically turns lights off after 30-second
delay, or lock switch on remote may be pushed after locking.
Automatic High Beam (AHB) system Automatically switches between high
and low beams as appropriate to provide the most light possible and enhance
forward visibility. Refer to Toyota Safety Sense™ P (TSS-P) in this guide or the
Owner’s Manual for more details on the Automatic High Beam feature.
* Operating conditions must be met. Refer to Owner’s Manual for details.
TURN SIGNALS
The power switch must be in the “IGNITION ON” mode.
Steering wheel-heater (if equipped)
OVERVIEW FEATURES & OPERATIONS TOYOTA SAFETY SENSE SAFETY & EMERGENCY FEATURES
Lights & turn signals
HEADLIGHTS

38
TOYOTA SAFETY SENSE™
AHB is a safety system designed to help drivers see more of what’s ahead at
nighttime and reduce glare for oncoming drivers. When enabled, AHB uses an
in-vehicle camera to help detect the headlights of oncoming vehicles and tail lights
of preceding vehicles, then automatically switches between high and low beams
as appropriate to provide the most light possible and enhance forward visibility.
By using high beams more frequently, the system may allow earlier detection of
pedestrians and obstacles.
Refer to a Toyota Owner’s Manual for additional information on AHB operation,
settings adjustments, limitations, and precautions before attempting to use it.
Automatic High Beams (AHB)
When all of these conditions are met, high beams will be automatically turned on
(after approximately 1 second):
• Vehicle speed is above approximately 21 mph (34 km/h.)
• The area ahead of the vehicle is dark.
• There are no oncoming or preceding vehicles with headlights or tail lights
turned on.
• There are few street lights on the road ahead.
If any of these conditions occur, the system is designed to automatically turn off
high beams:
• Vehicle speed drops below approximately 17 mph (27 km/h.)
• The area ahead of the vehicle is not dark.
• Oncoming or preceding vehicles have headlights or tail lights
turned on.
• There are many streetlights on the road ahead.
ACTIVATING THE AHB SYSTEM
CONDITIONS WHERE AHB WILL TURN ON/OFF AUTOMATICALLY
(2) (1)
(1) With the engine switch in IGNITION ON mode, turn the headlight switch to
“AUTO” position.
(2) Push lever away from you.
(3) Press the “
” switch.
The AHB indicator will come on when the headlights are turned on automatically
to indicate that the system is active.
Note: Pull the lever back toward you to turn the AHB system off.
The AHB indicator will turn off. To turn switch to “
” position and the manual
high beam indicator “
” turns on.