2019 Peugeot 208 display

102
F Move your vehicle for ward until a new
message is displayed.
F

S
elect reverse and release the steering
wheel. The assisted parking manoeuvre is in progress.
Without exceeding 5
mph (8 km/h), continue
the manoeuvres following the information given
by the "Parking sensors" system, until the end
of manoeuvre message is displayed.
The indicator lamp in the control goes off,
accompanied by an audible signal.
The driver takes back control of the vehicle's
steering.
Exit from a parallel parking
sp ace
F When you want to exit from a parallel
parking space, start the engine.
With the vehicle stationary, to activate the Park
Assist system:
F

P
ress this control.
The indicator lamp in the control remains off.
A message is displayed in the screen.
F

S
elect the exit parking space manoeuvre.
The indicator lamp in the control comes on.
F

O
perate the direction indicator on the exit
from parking side.
T

he direction indicator flashes throughout
the manoeuvre, whatever the position of the
control stalk.
F

S
elect a for ward or reverse gear then
release the steering wheel.
Once measurement is complete, if the space is
large enough a


message indicates that parking
is possible.
Driving

103
The assisted exit from parking manoeuvre is in
progress.
Without exceeding 3 mph (5 km/h), continue
the manoeuvres following the information given
by the "Parking sensors" system, until the end
of manoeuvre message is displayed.
The manoeuvre is complete once the front
wheels of the vehicle are out of the parking
space.
The indicator lamp in the control goes off,
accompanied by an audible signal.
The driver takes back control of the vehicle's
steering.
Deactivation
The system is deactivated automatically:
- o n switching off the ignition,
-

i
f the engine stalls,
-

i
f no manoeuvre is per formed within
5
minutes of selecting the type of
manoeuvre,
-

a
fter a prolonged stop of the vehicle during
a


manoeuvre,
-

i
f the wheel anti-slip regulation (ASR) is
triggered,
-

i
f the speed of the vehicle exceeds the
stated limit,
-

w
hen the driver interrupts movement of the
steering wheel,
-

i
f the driver presses the Park Assist control,
-

i
f the vehicle cannot be properly positioned
(too many manoeuvres to get the vehicle in
or out),
-

i
f the driver's door is opened,
-

i
f one of the front wheels encounters an
obstacle.
A message is displayed in the screen. The driver then takes back control of the
vehicle's steering.
If the system is deactivated during
a


manoeuvre, the driver should reactivate
it manually to repeat the measurement.
Deactivation
The system is switched off automatically:
- w hen towing a trailer,
-

i
f the driver's door is opened,
-

i
f the speed of the vehicle is above 43 mph
(70


km/h).
To switch the system off for a
prolonged period,
contact a
PEUGEOT dealer or a qualified
workshop.
6
Driving

104
Malfunctions
In the event of a system fault, this
w arning lamp is displayed in the
instrument panel and/or a
message
appears in the screen, accompanied
by an audible signal (short beep).
The indicator lamp in the control
flashes for a
few seconds. If the
problem occurs while using the
system, the indicator lamp goes off.
In the event of a
fault with the power
steering, these warning lamps come
on in the instrument panel.
Contact a
PEUGEOT dealer or a qualified
workshop.
If the lateral distance between your vehicle and the
space is too great, the system may not be able to
measure the space.
Any object exceeding the dimensions of the vehicle
(e.g. long or wide load) is not taken into account by
the Park Assist system during a
manoeuvre.
In bad and wintry weather, ensure that the
sensors are not covered by road dirt, ice
or snow.
In the event of a fault, have the system
checked by a
PEUGEOT dealer or
a


qualified workshop.
Driving

1
Audio system
Contents
First steps
1
S

teering mounted controls
2
R

adio
2
M

edia
3
A

udio settings
5
F

requently asked questions
5
F

or safety reasons, the vehicle must
always be stationary for the driver to
perform operations that require close
attention.
When the engine is switched off and to
prevent discharging of the battery, the
system switches off after activation of
energy economy mode.First steps
On/Off, volume adjustment.
Select the source:
FM1, FM2, AM, CD, AUX.
Adjust audio settings:
sound ambience, treble, bass,
loudness, left/right balance,
automatic volume.
Automatic search for a
lower radio
frequency.
Select the previous CD track.
Scroll in a
list.
Press and hold: rewind. Display the list of stations received,
the CD/MP3
tracks or folders.
Press and hold: update the list of
stations received.
Manual search step by step for
a

higher radio frequency.
Select the next MP3 folder.
Scroll in a list.
Manual search step by step for
a lower radio frequency.
Select the previous MP3 folder.
Scroll in a list.
Cancel the current operation.
Go up one level (menu or folder).
Automatic search for a
higher radio
frequency.
Select the next CD track.
Scroll in a
list.
Press and hold: fast for ward.
Access to the main menu.
Select a


preset radio station.
Radio, press and hold: store
a


station.
Eject CD.
.
Audio system

2
Steering mounted controls
Radio: select the previous/next
preset radio station.
Select the previous/next item in
a menu.
Radio: automatic search for a
higher
frequency.
CD/MP3: select the next track.
CD: press and hold: fast for ward.
Change the audio source.
Confirm a


selection.
Radio: automatic search for a
lower
frequency.
CD/MP3: select the previous track.
CD: press and hold: rewind.
Increase volume.
Decrease volume.
Mute on: cut the sound by
simultaneously pressing the volume
up and down buttons.
Mute off: press one of the two
volume buttons.
Radio
Presetting a station
Press the SRC/BAND button
repeatedly to select the FM1, FM2 or
AM waveband.
Press and hold a
button to preset
the station being listened to. The
name of the station is displayed and
an audible signal confirms that it has
been preset.
The external environment (hills, buildings,
tunnels, basement car parks, etc.) may
block reception, including in RDS tracking
mode. This is a
normal effect of the way
in which radio waves are transmitted and
does not indicate any failure of the audio
equipment.
Selecting a station
Press a button to listen to the
c orresponding preset station.
Managing the list
Press LIST to display the list of
stations received in alphabetical
o r d e r. Select the desired radio station by
pressing one of the buttons.
Confirm with OK.
Briefly press one of the buttons to
change to the next or previous letter.
Press and hold LIST
to build or
update the list of stations; audio
reception is cut momentarily.
Press MENU .
Select " Radio".
Confirm with OK.
Select " RDS".
RDS
RDS, if displayed, allows you to continue
listening to the same station by automatically
retuning to alternative frequencies. However,
in certain conditions, coverage of an RDS
station may not be assured throughout the
entire country as radio stations do not cover
100% of the territory. This explains the loss
of reception of a
station during a journey.
Audio system

3
Confirm with OK.
Select "On" or " Off" to switch RDS
on or off.
Confirm with OK.
Receiving TA messages
The TA (Traffic Announcement) function
gives priority to TA alert messages.
To operate, this function needs good
reception of a
radio station transmitting
this type of message. When a
traffic
report is transmitted, the current audio
source (radio, CD, etc.) is interrupted
automatically to play the TA message.
Normal playback resumes at the end of
the transmission of the message.
Press MENU .
Select "Radio ".
Confirm with OK.
Select " Traffic TA ".
Confirm with OK. Select "
On" or " Off" to activate or
deactivate the reception of traffic
messages.
Confirm with OK.
Displaying RADIO TEXT
Radio Text is information transmitted by
the radio station related to the current
programme or song.
Press MENU .
Select " Radio".
Confirm with OK.
Select " INFO TEXT ".
Confirm with OK.
Select " On" or " Off" to switch Radio
Text on or off.
Confirm with OK.
Media
Auxiliary socket (AUX)
Connect a portable device (MP3 player, etc.) to
t he auxiliary Jack socket using an audio cable
(not supplied).
Press the SRC/BAND button
repeatedly until the " AUX" source is
displayed.
First adjust the volume on your portable device
(to a
high level). Then adjust the volume of your
audio system. Management of the controls is
via the portable device.
CD player
Insert a CD in the player; play begins
au tomatically.
Insert an MP3
compilation in the CD player.
The audio system searches for all of the music
tracks, which may take anything between a
few
seconds and several tens of seconds, before
play begins.
.
Audio system

4
Press the SRC/BAND button
repeatedly to select " CD".
Press one of these buttons to go to
the previous/next track in the list.
Press one of these buttons to select
the previous or next folder in the
order chosen.
Press and hold one of these buttons
for fast for ward or rewind.
Playing a compilation
Press LIST to display the folder
structure of the compilation.
Select a
line in the list.
Confirm with " OK".
Jump a
page.
Select a


folder/Playlist.
Start play of the chosen track. Go up one level.
Go back to the first level to select the track
classification:
- By
Folders : all folders containing audio
files recognised on the peripheral device,
in alphabetical order, ignoring the folder
structure.
- By
Playlist : depending on the playlists
saved.
Play mode
Press MENU .
Select "Media ".
Confirm with OK.
Select the desired play mode.
Confirm with OK to save the
changes. The play modes available are:
-

N
ormal: the tracks are played in order,
depending on the classification of the
selected files.
-
R
andom: the tracks in an album or
folder are played in a random order.
-
R
andom all: all of the tracks saved in
the media are played in random order.
-
R
epeat: the tracks played are only
those from the current album or folder.Information and advice
The audio system can only play files with
".mp3", ".wma" or ".wav" extensions.
To avoid any playback or display issues, it is
advisable to create file names that have less
than 20


characters and without using any
special characters (e.g. " ?.; ù).
In order to be able to play a
recorded CDR
or CDRW, it is preferable to select the
ISO
9660 level 1, 2 or Joliet standard when
recording the CD.
If the disc is burned in another format, it may
not be played correctly.
It is recommended that the same recording
standard is always used for a
given disc, with
as low a
speed as possible (4x maximum) for
optimum sound quality.
Audio system

5
In the particular case of a multi-session CD, the
J oliet standard is recommended.
Playlists accepted are types ".m3u" and ".pls".
The system can recognise up to 5,000
files in
500
folders on 8 levels.
On a
given disc, the CD player can read up to
255
MP3 files spread over 8 levels. However,
it is recommended that this be kept to 2
levels
so as to limit the time taken to access and play
the CD.
The folder structure is not obser ved during
playback.
Audio settings
Press ¯ to display the audio
settings menu.
The settings available are:
-

AMBIENCE,
-

BASS,
-


TREBLE,
-


LOUDNESS,
-

L

/R BALANCE,
-
A

UTO VOLUME. Select the setting to adjust.
Confirm with OK. Adjust the setting.
Confirm with OK.
The AMBIENCE, TREBLE and BASS
audio settings are different and
independent for each sound source.
Frequently asked questions
The following information groups together the
answers to the most frequently asked questions
concerning your audio system.
.
Audio system