2019 Peugeot 208 display

6
QUESTIONRESPONSESOLUTION
There is a difference in sound quality between
the different audio sources (radio, CD, etc.). To allow for optimal listening quality, the audio
settings (Volume, Bass, Treble, Ambience,
Loudness) can be tailored to different
sound sources, which can generate audible
differences when changing source (radio, CD,
e t c .) .Check that the audio settings (Volume, Bass,
Treble, Ambience, Loudness) are adapted to
the sources listened to. It is advisable to set
the AUDIO functions (Bass, Treble, Front-
Rear Fader, Left-Right Balance) to the middle
position, select the musical ambience "None"
and set the loudness correction to the "Active"
position in CD mode or to the "Inactive" position
in radio mode.
When changing the settings for treble and bass,
the ambiance setting is deselected.
When changing the ambience setting, treble
and bass are reset to zero. Choosing an ambience imposes settings for
treble and bass. Modifying one without the other
is not possible.
Modify the treble and bass settings or the
ambience setting to obtain the desired sound
quality.
The reception quality of the tuned radio station
gradually deteriorates or the stored stations are not
working (no sound, 87.5
MHz is displayed, etc.).The vehicle is too far from the transmitter of
the station or no transmitter is present in the
geographical area. Activate the RDS mode and start a
new search
for the station so that the system can check
whether a
stronger transmitter is available in the
geographic area.
The environment (hills, buildings, tunnels,
basement car parks, etc.) blocks reception,
including in RDS tracking mode. This phenomenon is normal and does not
indicate a
failure of the audio equipment.
The aerial is missing or has been damaged (for
example when going through a
car wash or into
an underground car park). Have the aerial checked by a
PEUGEOT dealer.
Audio system

7
Sound cut-outs of 1 to 2 seconds in radio mode. During this brief sound cut-out, the RDS
searches for any frequency permitting better
reception of the station. Switch off the RDS function if the phenomenon
is too frequent and always on the same route.
The traffic announcement (TA) is displayed. I do
not receive any traffic information. The radio station does not broadcast traffic
information.Tune to a
radio station which broadcasts traffic
information.
The stored stations are not found (no sound,
87.5
MHz is displayed, etc.). An incorrect waveband is selected.
Press the SRC button to return to the waveband
(AM, FM1, FM2) on which the stations are
stored.
The CD is ejected every time or is not played. The CD is upside down, cannot be read, does not contain audio files or contains audio files
of a
format that cannot be played by the audio
system.
The CD is protected by an anti-pirating system
not recognised by the audio system. -

C
heck that the CD is inserted in the player
the right way up.
-

C
heck the condition of the CD: the CD
cannot be played if it is too badly damaged.
-

C
heck the content in the case of a recorded
CD: consult the advice in the "Media"
section.
-

T
he audio system's CD player does not play
DVDs.
-

B
ecause of low quality, certain burned CDs
will not be read by the audio system.
The CD sound is of poor quality. The CD used is scratched or of poor quality. Insert good quality CDs and store them in
suitable conditions.
The audio settings (bass, treble, ambiences) are
unsuitable. Return bass and treble settings to 0, without
selecting an ambience.
.
Audio system

8
In "Random all" play, not all of the tracks are
played.In "Random all" play, the system can only take
into account up to 999
tracks.
With the engine off, the audio system switches
off after a
few minutes of use. When the engine is switched off, the audio
system operating time depends on the battery
charge.
The switch-off is normal: the audio system
switches to economy mode and switches off to
prevent discharging the vehicle's battery. Start the vehicle's engine to increase the battery
charge.
The message "the audio system is overheated"
appears on the display. In order to protect the installation if the
surrounding temperature is too high, the audio
system switches to an automatic thermal
protection mode leading to a
reduction of the
volume or stopping of the playing of the CD. Switch the audio system off for a
few minutes to
allow the system to cool.
Audio system

1
Audio system/Bluetooth®
Contents
First steps
1
S

teering mounted controls
2
R

adio
2
M

edia
3
T

elephone
6
A

udio settings
8
C

onfiguration
9
F

requently asked questions
9
F

or safety reasons, the vehicle must
always be stationary for the driver to
perform operations that require close
attention.
When the engine is switched off and to
prevent discharging of the battery, the
system switches off after activation of
energy economy mode.First steps
On/Off, volume adjustment.
Adjust audio options: sound
ambience, treble, bass, loudness,
distribution, left/right balance, front/
rear balance, automatic volume.
Automatic search for a
lower radio
frequency.
Select the previous CD, USB track.
Scroll in a
list.
Press and hold: rewind. Display the list of stations received,
the CD/USB tracks or folders.
Press and hold: update the list of
stations received.
Cancel the current operation.
Go up one level (menu or folder).
Automatic search for a
higher radio
frequency.
Select the next CD, USB track.
Scroll in a list.
Press and hold: fast for ward.
Access to the main menu.
Select preset radio station.
Radio, press and hold: store
a


station.
Other than radio: see the
corresponding sections.
Eject CD.
Select the source:
Radio: FM1, FM2, AM, CD, USB,
AUX, Streaming.
Telephone: accept an incoming call.
Telephone, press and hold: end
a
call, access the calls log for the
connected telephone.
.
Bluetooth® audio system

2
Steering mounted controls
Radio: select the previous/next
preset radio station.
CD/USB: select the genre/artist /
folder from the classification list.
Select the previous/next item in
a menu.
Radio: automatic search for higher
frequency.
CD/MP3/USB: select the next track.
CD/USB: press and hold: fast
forward.
Change the audio source.
Confirm a


selection.
Call/end call on the telephone.
Press and hold: access to the calls
list.
Radio: automatic search for lower
frequency.
CD/MP3/USB: select the previous
track.
CD/USB: press and hold: rewind.
Increase volume.
Decrease volume. Mute on: cut the sound by
simultaneously pressing the volume
increase and decrease buttons.
Mute off: press one of the two
volume buttons.
Radio
Presetting a station
Press SRC/TEL
repeatedly to select
the FM1, FM2 or AM waveband.
Press and hold a
button to preset
the station being listened to. The
name of the station is displayed and
an audible signal confirms that it has
been preset.
The external environment (hills, buildings,
tunnels, basement car parks, etc.) may
block reception, including in RDS tracking
mode. This is a
normal effect of the way
in which radio waves are transmitted and
does not indicate any failure of the audio
equipment.
Selecting a station
Press a button to listen to the
c orresponding preset station.
Managing a list
Press LIST to display the list of
stations received in alphabetical
o r d e r.
Select the desired radio station
using one of the buttons.
Confirm with " OK".
Briefly press one of the buttons to
change to the next or previous letter.
Press and hold LIST to build or
update the list of stations; audio
reception is cut momentarily.
Entering a frequency
Press MENU .
Select "Radio ".
Select "Write freq. ".
Press + ,
or press – to select the desired
frequency.
Confirm with " OK".
Bluetooth® audio system

3
RDS
RDS, if activated, allows you to continue
listening to the same station by automatically
retuning to alternative frequencies. However, in
certain conditions, coverage of an RDS station
may not be assured throughout the entire
country as radio stations do not cover 100% of
the territory. This explains the loss of reception
of a station that can occur during a journey.
With source FM1 or FM2, press
M ENU .
Select "Radio ".
Select or deselect "RDS " to switch
RDS on or off.
Confirm with " OK" to save the
setting.
Receiving TA messages
The TA (Traffic Announcement) function
gives priority to TA alert messages.
To operate, this function needs good
reception of a
radio station transmitting
this type of message. When a
traffic
report is transmitted, the current audio
source (radio, CD, USB, etc.) is interrupted
automatically to play the TA message.
Normal playback resumes at the end of
the transmission of the message. Press MENU
.
Select "Radio ".
Select or deselect " TA" to activate
or deactivate the reception of traffic
messages.
Confirm with " OK" to save the
setting.
Displaying RADIO TEXT
Radio Text is information transmitted by
the radio station related to the current
programme or song.
With the radio displayed on the
screen, press MENU .
Select " Radio".
Select or deselect " TXT" to activate
or deactivate the display of Radio
Te x t .
Confirm with " OK" to save the
setting.
Media
USB socket
This unit comprises a USB socket and an
a uxiliary Jack socket, depending on model.
The system builds playlists (in temporary
memory), an operation which can take
from a
few seconds to several minutes at
the first connection.
Reduce the number of non-music files
and the number of folders to reduce the
waiting time. The playlists are updated
every time the ignition is switched off or
a
USB memory stick is connected.
The lists are memorised: if they are not
modified, the subsequent loading time will
b e s h o r t e r.
.
Bluetooth® audio system

4
Insert the USB memory stick into the USB
socket or connect the USB device to the USB
socket using a

suitable cable (not supplied).
To protect the system, do not use a
USB
hub.
Press SRC/TEL repeatedly to select
" USB ".
Press one of these buttons to select
the previous or next track in the list.
Press one of these buttons to select
the previous or next folder according
to the category chosen.
Press and hold one of these buttons
for fast for ward or rewind.
Press LIST to display the structure
of the folders in the compilation.
Select a
line in the list.
Confirm with " OK".
Go up a
level in the menu. Press MENU
.
Select "Media ".
Select or deselect " TA" to activate
or deactivate the reception of traffic
announcements.
Select the playback mode:
" Normal ", "Random ", "Random all"
or " Repeat ".
Auxiliary socket (AUX)
Connect a portable device (MP3 player, etc.) to
t he auxiliary Jack socket using an audio cable
(not supplied).
Press SRC/TEL repeatedly to select
" AUX ".
First adjust the volume on your portable device
(to a
high level). Then adjust the volume of your
audio system. Management of the controls is
via the portable device. Do not connect the same device to both
the Jack auxiliary socket and the USB
socket at the same time.
CD player
Insert a CD in the player; play begins
au tomatically.
Insert an MP3
compilation in the CD player.
The audio system searches for all of the music
tracks, which may take anything between a
few
seconds and several tens of seconds, before
play begins.
Press the SRC/TEL button
repeatedly to select " CD".
Press one of these buttons to go to
the previous/next track in the list.
Press one of these buttons to select
the previous or next folder in the
order chosen.
Press and hold one of these buttons
for fast for ward or rewind.
Press LIST to display the folder
structure of the compilation.
Bluetooth® audio system

5
Select a line in the list.
C onfirm with " OK".
Return to the top level of the folder structure to
select the type of tracks.
-

By Folders (CD or USB): all folders
containing audio files recognised on the
peripheral device, in alphabetical order
without following the folder structure.
-

By Artist (USB only): all of the artist names
defined in the ID3


Tags, in alphabetical
o r d e r.
-

By Genre (USB only): all of the genres
defined in the ID3
Tags.
-

By Playlist (CD or USB): if playlists have
been saved.
Information and advice
The audio system will only play files with
".mp3", ".wma" and ".wav" extensions on a CD
and can play files with ".ogg" extension only on
USB.
File names should have less than
20


characters, avoiding special characters
(e.g. " ?; ù) so as to avoid any reading or
display problems. If the disc is burned in another format, it may
not be played correctly.
It is recommended that the same burning
standard is always used on an individual disc,
with the lowest speed possible (4x maximum)
for the best acoustic quality.
In the particular case of a
multi-session CD, the
Joliet standard is recommended.
The playlists accepted on CD, MP3, iPod and
USB connection are types ".m3u" and ".wpl".
The system can recognise up to 5,000 files in
500 folders on 8 levels.
On a single disc, the CD player can read up
to 255 MP3 files spread over 8 folder levels
with a maximum of 192 folders. However, it
is recommended that the number of levels is
limited to 2 so as to reduce the time taken to
access and play the CD.
The folder structure is not obser ved during
playback.
Do not connect a hard disk or USB device other
than audio players to the USB socket. This may
cause damage to your installation.
Use only USB memory sticks formatted to FAT
32
(File Allocation Table).To protect the system, do not use a
USB
hub.
Bluetooth® audio streaming
Streaming allows music files on a telephone to
b e heard via the vehicle's speakers.
Connect the telephone: see the " Telephone"
section.
In the " Bluetooth: Audio " menu, select the
telephone to be connected.
The audio system connects to a
newly paired
telephone automatically.
Activate the streaming source by
pressing the SRC/TEL button.
In certain cases, play of the audio
files must be initiated from the
keypad.
The control of common tracks is possible
via the audio system control buttons and the
steering mounted controls, if the telephone
supports the function.
Contextual information can be displayed in the
screen.
The audio quality depends on the quality of
transmission by the telephone. It is recommended that you use genuine
Apple
® USB cables for correct operation.
In order to be able to play a

burned CDR or
CDRW, select standards ISO

9660

level 1, 2

or
Joliet if possible when burning the CD.
.
Bluetooth® audio system