2019 Peugeot 208 Owner's Manual

23
Remaining range less than 60 miles
( 100 km) (1.5 BlueHDi Euro 6.2)
When driving, the audible signal and the
message display are triggered every 6
miles
(10
km) until the AdBlue tank is topped up.
It is essential to top up as soon as possible and
before the tank is completely empty; other wise
it will not be possible to restart the engine after
the next stop.
Breakdown related to a
lack of AdBlue
®
The AdBlue® tank is empty: the starting
prevention system required by legislation
prevents starting of the engine. It is essential to top up as soon as possible and
before the tank is completely empty; other wise
it will not be possible to restart the engine after
the next stop.
When switching on the ignition, this warning
lamp flashes, accompanied by an audible
signal (1

beep) and the display of a message
("Top up AdBlue: Starting impossible in
x miles") indicating the remaining range
expressed in miles or kilometres.
When switching on the ignition, this warning
lamp flashes, accompanied by an audible
signal and the display of the message "Top up
AdBlue: Starting impossible". To be able to restart the engine, it is
essential to add at least 5 litres of AdBlue
®
to its tank.
For more information on AdBlue
®
(BlueHDi engines) , and, in particular,
on topping up, refer to the corresponding
section.
In the event of a fault with the
S CR emissions control system
A system that prevents engine starting is
activated automatically from 685
miles
(1,100
km) after confirmation of a fault with
the SCR emissions control system.
Have the system checked by a
PEUGEOT
dealer or a
qualified workshop as soon as
possible.
In the event of the detection of a
faultIf it is a
temporary fault, the alert
disappears during the next journey, after
self-diagnosis of the SCR system.
During the permitted driving phase
(between 685 and 0 miles (1,100 and 0 km))
These warning lamps come on, accompanied
by an audible signal and the display of the
message "Emissions fault".
The alert is triggered when driving when the
fault is detected for the first time, then when switching on the ignition for subsequent
journeys, while the fault persists.
If a
fault with the SCR system is confirmed
(after 31
miles (50 km) covered with the
permanent display of the message signalling
a
fault), these warning lamps come on and the
AdBlue warning lamp flashes, accompanied by
an audible signal and the display of a
message
(e.g. "Emissions fault: Starting prevented in
185
miles") indicating the remaining range in
miles or kilometres.
While driving, the message is displayed every
30
seconds while the fault with the SCR
emissions control system persists.
The alert is repeated when switching on the
ignition.
You should go to a
PEUGEOT dealer or
a
qualified workshop as soon as possible.
Other wise you will not be able to restart the
vehicle.
1
Instruments

24
Starting preventedYou have exceeded the authorised driving
limit: the starting prevention system does
not allow the engine to be started.
To be able to restart the engine, you must call
on a
PEUGEOT dealer or a qualified workshop.
Each time the ignition is switched on, these
warning lamps come on and the AdBlue
warning lamp flashes, accompanied by an
audible signal and the display of the message
"Emissions fault: Starting prevented".
Trip computer
Instrument panel screen
F Each press on the end of the wiper
control stalk displays the information in
turn. -
Trip
1 with:
•
t
he average speed,
•
t
he average fuel consumption,
•
t
he distance travelled,
for the first trip.
- Trip
2 with:
•
t
he average speed,
•
t
he average fuel consumption,
•
t
he distance travelled,
for the second trip.
-
T
he current information with:
•
t
he range,
•
t
he current fuel consumption,
•
t
he Stop & Start time counter.
With touch screen
The information is accessible via the
Driving/Vehicle
.
Reset trip
F When the desired trip is displayed, press
the button located on the end of the wiper
control stalk for more than 2
seconds.
Trips 1
and 2 are independent and are used
identically.
For example, trip 1
can be used for daily figures
and trip 2
for monthly figures.
Display of information on the touch screen
Instruments

25
Permanent display:
F Sel ect the " Applications " menu, then the
" Vehicle apps " tab, then "Trip computer ".
The trip computer information is displayed in
tabs.
F

P
ress one of the buttons to display the
desired tab.
Temporar y display in a
specific window:
F

P
ress the end of the wiper control stalk
to access the information and display the
different tabs.
The current information tab with:
-

T
he range.
-

T
he current fuel consumption.
-

T
he Stop & Start time counter.
The trip " 1" tab with:
-

T
he average speed for the first trip.
-
T

he average fuel consumption.
-

T
he distance travelled.
The trip " 2" tab with:
-

T
he average speed for the second trip.
-
T

he average fuel consumption.
-

T
he distance travelled.Trip reset
F When the desired trip is displayed, press the reset button or on the end of the wiper
control stalk.
Tr i p s " 1" and " 2" are independent and are used
identically.
For example, trip " 1" can be used for daily
figures and trip " 2" for monthly figures.
A few definitions
Range
(miles or km)
The distance which can still be
travelled with the fuel remaining in
the tank (related to the average fuel
consumption over the last few miles
(kilometres) travelled).
This value may fluctuate if a
change
of driving style or terrain results in
a
significant change in the current fuel
consumption.
Dashes are displayed when the range falls
below 19
miles (30 km).
After filling with at least 5
litres of fuel, the
range is recalculated and is displayed if it
exceeds 60
miles (100 km).
If dashes instead of figures continue
to be displayed when driving, contact
a PEUGEOT dealer or a qualified workshop.
Current fuel consumption
(mpg or l/100 km or km/l)
C alculated over the last few seconds.
1
Instruments

26
This function is only displayed from
19 mph (30 km/h).
Average fuel consumption
(mpg or l/100 km or km/l)
C alculated since the last trip computer
reset.
Distance travelled
(miles or km)
Calculated since the last trip computer
reset.
Average speed
(mph or km/h) Calculated since the last trip
computer reset.
Total time in stop mode
(minutes/seconds or hours/minutes)
If your vehicle is fitted with Stop & Start, a time
counter adds up the time spent in STOP mode
during a

journey.
It resets to zero every time the ignition is
switched on.
Setting the time and date
Instrument panel
F Each press of this button toggles between the following settings:
-


h o u r,
-


minutes,
-

1
2 or 24 hour format.
With PEUGEOT Connect
Radio
F Select the Settings menu in
the upper banner of the touch
screen.
F

Sel

ect " System configuration ".
F

Sel
ect "Date and time ".
F

Sel

ect " Date " or "Time ".
F

C

hoose the display formats.
F

C

hange the date and/or time using the
numeric keypad.
F

C

onfirm with " OK".
With PEUGEOT Connect
Nav
Setting of the time and date is only available if
synchronisation with the GPS is deactivated.
F

Sel
ect the "Settings " menu.
F

P
ress the " OPTIONS " button to go to the
secondary page.
F

Sel
ect "Setting the time- date".
F

Sel
ect the " Date" or " Time" tab.
F

A
djust the date and time using the numeric
keypad and confirm.
F

I
n the selected tab, press this
key to confirm.
Additional settings
You can choose:
- T o change the date format (DD/MM/ Y Y Y Y,
YYYY/MM/DD, etc.)
-

T
o change the time format (12h/24h).
-

T
o change the time zone.
-

T
o activate or deactivate synchronisation
with the GPS (UTC).
Instruments

27
The system does not automatically
manage the change between winter and
summer time (depending on country).
The change between winter and summer
time is done by changing the time zone.
Lighting dimmer
System for the manual adjustment of the
brightness of the instrument panel and the
touch screen to suit the ambient light level.
With two buttons
Lighting switched on:F
P
ress this button to raise
the level of brightness.
F

P
ress this button to lower
it.
Release the button once the desired level of
brightness is reached.
With one button
F Press this button to adjust the brightness.
F

R

elease the button once the desired level
of brightness is reached.
When the vehicle lighting is off, or in day
mode (daytime running lamps on), pressing
the button does not have any effect.
With touch screen
The brightness can be adjusted differently
for day mode (lighting control stalk in
position " 0") and night mode (lighting
control stalk in any other position).
F

I

n the Settings menu, select " Brightness".
F

A

djust the brightness by pressing the
arrows or moving the slider.
1
Instruments

28
Remote control key
System which permits central unlocking or
locking of the vehicle using the door lock or
from a distance.
It also ensures the localisation and starting of
the vehicle, as well as theft protection.
A. Unfolding/Folding.
B. Unlocking.
Disarming the alarm.
C. Locking.
Locating the vehicle.
Arming the alarm.
D. Guide-me-home lighting.
Unfolding/Folding the key
F Press button A to unfold/fold the key. If you do not press the button, you risk
damaging the remote control.
Unlocking the vehicle
With the key
F Turn the key in the driver's door lock
towards the front of the vehicle to
unlock.
With the remote control
F Press this button to unlock the vehicle.
Unlocking is confirmed by rapid flashing of
the direction indicators for a
few seconds.
Depending on version, the door mirrors unfold
and the welcome lighting comes on.
Unlocking with the key does not deactivate the
alarm.
Selective unlocking of the
driver's door
Complete unlocking is activated by default.
With the touch screen, selective
unlocking can be configured from
the Driving/Vehicle menu. F

P
ress this button to unlock the
driver's door only. Press twice in
quick succession to unlock the
other doors and the boot.
Locking the vehicle
With the key
F Turn the key in the driver's door lock towards the rear of the vehicle to lock it.
Check that the doors and boot are fully
closed.
With the remote control
F Press this button to lock the vehicle.
Locking is confirmed by fixed illumination of
the direction indicators for approximately two
seconds. Depending on version, the door
mirrors fold.
If one of the doors or the boot is still open,
the central locking does not work; the vehicle
locks, then immediately unlocks, identifiable by
the locks making a


rebound sound.
Access

29
When the vehicle is locked, if it is
unlocked without the opening of a door
or the boot, it will automatically lock itself
again after thirty seconds.
Locating your vehicle
F A press switches on the vehicle's lighting and flashes the direction
indicators for a
few seconds to
help you locate your vehicle.
Guide-me-home lighting
Make a long press on this button to
o perate the guide-me-home lighting
(switching on the sidelamps, dipped
beams and number plate lamps).
A second press before the end of the timed
period cancels the guide-me-home lighting.
Deadlocking
Deadlocking deactivates the exterior and
interior door controls as well as the central
locking button on the dashboard.
You must therefore never leave anyone
inside the vehicle when it is deadlocked.
With the key
F Turn the key to the rear in the driver's door lock.
F

T
urn the key to the rear again within
5
seconds to deadlock the vehicle.
With the remote control
F Press this button once to lock the vehicle fully.
F

P
ress this button again within
5
seconds to deadlock the
vehicle.
Deadlocking is confirmed by fixed
lighting of the direction indicators for
approximately 2


seconds.
Depending on the version you have, the
electric door mirrors fold at the same time.
Advice
Remote control
The high frequency remote control is
a
sensitive system; do not operate it while
it is in your pocket as there is a
possibility
that it may unlock the vehicle, without you
being aware of it.
Do not press the buttons of your remote
control out of range and out of sight of
your vehicle. It might stop working. It will
then be necessary to reinitialise it again.
The remote control does not operate when
the key is in the ignition, even when the
ignition is switched off.
Anti-theft protection
Do not make any modifications to the
electronic engine immobiliser system; this
could cause malfunctions.
For vehicles with an ignition switch, do
not forget to remove the key and turn the
steering wheel to engage the steering
lock.
The automatic folding and unfolding of the
door mirrors can be deactivated via the
vehicle's configuration menu.
2
Access

30
Central locking
Manual
F Press this button to operate the central locking of the vehicle (doors and boot) from inside the vehicle.
The indicator lamp in the button comes on.
F

P
ressing the button again unlocks the vehicle
completely. The indicator lamp in the button goes
of f.
The indicator lamp also goes off when
unlocking one or more doors.
The central locking does not work if one of
the doors is open.
Automatic (anti-intrusion
security)
The doors and boot can lock automatically
while driving (speed above 6 mph (10 km/h)).
To activate or deactivate this function (activated
by default):
F

P
ress the button until an audible
signal is heard and/or a
message
appears in the screen.
Back-up procedures
Total unlocking/locking of
the vehicle with the key
Use these procedures in the following cases:
- r emote control cell battery flat,
-

r
emote control fault,
-

v
ehicle in an area subject to strong
electromagnetic interference.
In the first case, you can also replace the
remote control cell battery.
In the second case, you can also reinitialise the
remote control.
Refer to the corresponding sections.
Locking the vehicle
Driving with the doors locked could make it
difficult for the emergency services to enter
the vehicle in an emergency.
As a
safety precaution (with children on
board), remove the key from the ignition when
leaving the vehicle, even for a
short time.
Lost keys, remote control
Go to a PEUGEOT dealer with the
vehicle's registration document, your
personal identification documents and if
possible the key code label.
The PEUGEOT dealer will be able to
retrieve the key code and the transponder
code required to order a
new key.
Purchasing a


second-hand vehicle
Have the key codes memorised by
a
PEUGEOT dealer, to ensure that the
keys in your possession are the only ones
which can start the vehicle.
If the vehicle is deadlocked or locked from
the outside, the button is not active. If the
vehicle is not deadlocked, use the remote
control to unlock the vehicle or pull an
interior door handle to open a
door.F

I
nsert the key in the door lock.
F

T
urn the key towards the front of the
vehicle to unlock it, or towards the rear to
lock it.
Access