2019 NISSAN ROGUE HYBRID ignition

The NISSAN PURE DRIVE® Hybrid System
combines the power of a gasoline engine
and an electric motor to help minimize fuel
consumption and emissions.
Depending on driving conditions, the ve-
hicle runs on a combination of the gasoline
engine and the electric motor, whichever is
best for those conditions.
Because the gasoline engine charges the
Lithium-ion (Li-ion) battery as needed, the
battery does not have to be charged from
an outside source like an all-electric ve-
hicle.WARNING
If you continue to drive the vehicle while
the warning is displayed, the hybrid
system may become temporarily inop-
erative and the system cannot provide
power to the wheels. This can result in
reduced or zero vehicle speed. The re-
duced speed or zero speed may be
lower than other traffic, which could in-
crease the chance of a collision. If the
vehicle cannot maintain a safe driving
speed, pull to the side of the road in a
safe area. If this occurs, place the shif t
lever in the P (Park) position and the
ignition in the READY to drive position
with the vehicle stopped until the dis-
play turns off. The “Hybrid System Over-
heated Stop Vehicle” warning and the
“Shif t to Park” warning will be alter-
nately displayed. For additional infor-
mation, refer to “Vehicle information
display warnings and indicators” in the
“Instruments and controls” section of
this manual.
WARNING
Your vehicle contains a sealed Lithium-
ion (Li-ion) high-voltage battery. If the
Li-ion battery is disposed of improperly,
there is a risk of severe burns and elec-
trical shock that may result in serious
injury or death and there is also a risk of
environmental damage.
CAUTION
∙ Do not misuse the Li-ion battery.
∙ Do not use the Li-ion battery for anyother purpose.
The Li-ion battery is used to drive the elec-
tric motors in the NISSAN PURE DRIVE® Hy-
brid System.
The Li-ion battery has a limited service life.
It is recommended that you visit a NISSAN
dealer for information about recycling or
disposal of the battery.
NISSAN PURE DRIVE® HYBRID
SYSTEM LITHIUM-ION (Li-ion) BATTERY
HEV-2HEV Overview

∙ Inspect the ground under the vehicle.If liquid has leaked onto the ground,
the fuel system may have been dam-
aged. Leave the vehicle as soon as
possible.
∙ Leaks or damage to the Li-ion battery may result in a fire. If you discover
them, contact emergency services
immediately. Since the fluid leak may
be lithium organic electrolyte from
the Li-ion battery, never touch the
fluid leak inside or outside the vehicle.
If the fluid contacts your skin or eyes,
wash it off immediately with a large
amount of water and receive immedi-
ate medical attention to help avoid
serious injury.
∙ If a fire occurs in the hybrid vehicle, leave the vehicle as soon as possible.
Only use a type ABC, BC or C fire extin-
guisher that is meant for use on elec-
trical fires. Using water or the incor-
rect fire extinguisher can result in
serious injury or death from electrical
shock. ∙ If you are not able to safely assess the
vehicle due to vehicle damage, do not
touch the vehicle. Leave the vehicle
and contact emergency services. Ad-
vise first responders that this is a hy-
brid vehicle.
∙ In the event of an accident that re- quires body repair and painting, the
vehicle should be delivered to a
NISSAN dealer to have the Li-ion bat-
tery pack and high-voltage parts such
as the inverter, including the wiring
harness, removed prior to painting. Li-
ion battery packs exposed to heat in
the paint booth will experience capac-
ity loss. Damaged Li-ion battery packs
may also pose safety risks to un-
trained mechanics and repair
personnel.The emergency shut-off system is activated
and the high-voltage system automatically
turns off in the following conditions:
∙ Front and side collisions in which the air bags are deployed.
∙ Certain rear collisions.
∙ Certain NISSAN PURE DRIVE® Hybrid System malfunctions.
For the above collisions and the certain
hybrid system malfunctions, the READY to
drive indicator light will turn off. For addi-
tional information, refer to “Warning lights,
indicator lights and audible reminders” in
the “Instruments and controls” section of
this manual.
The emergency shut-off activates for the
above collisions to minimize risk of an event
that could cause injury or an accident. If the
emergency shut-off system activates, the
hybrid system may not switch to the READY
to drive position. It is recommended that
you visit a NISSAN dealer. Even if the ignition
switch is placed in the READY to drive posi-
tion, the system may shut off suddenly.
Therefore, drive cautiously to the nearest
NISSAN dealer or contact a NISSAN dealer as
soon as possible.
EMERGENCY SHUT-OFF SYSTEM
HEV-4HEV Overview

To start the NISSAN PURE DRIVE® Hybrid
System, depress the brake pedal and place
the ignition switch in the ON position when
the transmission is in the P (Park) position.
CAUTION
Do not start the system in the N (Neu-
tral) position under cold condition of
the system. Start in the P (Park) position
in that case.
The READY to drive indicator light
flashes until the hybrid system is ready to
drive.
If starting in a low temperature environ-
ment, the flashing time of the READY to
drive indicator light
becomes longer.
It cannot move out from the P (Park) range
during flashing.
When the READY to drive indicator
light
illuminates, the vehicle can be
driven, even if the gasoline engine is not
running.
NOTE:
The gasoline engine starts and stops au-
tomatically. It may stop during decelera-
tion or when the vehicle is stopped.
The gasoline engine may automatically
run in the following conditions: ∙ The level of remaining charge in the Li-
ion battery is low. The engine runs to
charge the Li-ion battery and to provide
power to drive the vehicle.
∙ The temperature of the engine coolant is low.
∙ When the A/C is used.
∙ When opening the door.
∙ When the engine hood is opened.
∙ When applying the brakes.
∙ Based on driving conditions.
∙ The shif t lever is moved to the P (Park) position, the driver’s seat belt is re-
leased and the driver’s side door is then
opened.
The hybrid system operates as follows
based on driving conditions and the Li-ion
battery charge.
The engine is hard to stop during these
driving conditions: ∙ When the A/C is on and outside tem- perature is high/low.
∙ When repeatedly starting and stopping the engine.
STARTING AND SLOW SPEED
DRIVING
In some cases, the vehicle can be driven by
the electric motor during extremely slow
speed creep, but the engine starts when
accelerating or releasing the brakes.
MEDIUM OR HIGH SPEED DRIVING
The system automatically controls the
gasoline engine and electric motor in order
to obtain the optimum fuel mileage and
performance, depending on the driving
situation and available Li-ion battery
charge.
When the remaining battery level is low, the
Li-ion battery is charged by the electric
motor that is driven to generate electric
power while the vehicle is driving.
RAPID ACCELERATION
The vehicle is accelerated using both the
gasoline engine and the electric motor de-
pending on the available Li-ion battery
charge.
OPERATION OF THE HYBRID SYSTEM
HEV OverviewHEV-5

1. Lithium-ion (Li-ion) battery
2. Service plug
3. DC/DC converter
4. 12-volt battery
5. High-voltage harness
6. Traction motor inverter
7. Traction motor
The hybrid system uses high voltage up to
approximately 235 volts. High-voltage
components are indicated in the illustra-
tion. High-voltage harnesses are orange.
The system can be hot during and af ter
starting. Be careful of both the high voltage
and the high temperature.
HYBRID VEHICLE
CHARACTERISTICS
WARNING
∙ When you leave your vehicle, be sureto place the ignition switch in the OFF
position.
∙ Be sure to put the transmission in the P (Park) position because the vehicle
can move when the READY to drive
indicator light is on even if the gaso-
line engine is not running. When the
READY to drive indicator light is on, do
not leave your vehicle in a shif t posi-
tion other than the P (Park) position.
The vehicle will creep and start
abruptly if the accelerator pedal is de-
pressed by mistake. This may cause
serious injury or death.
CAUTION
If the vehicle is parked for a long period
of time, the battery discharges gradu-
ally. To avoid this occurrence, drive the
vehicle for approximately 30 minutes at
least once every two to three months.
Otherwise, the Li-ion battery may be
damaged. If the Li-ion battery is com-
pletely discharged and the hybrid sys-
tem cannot be activated, it is recom-
mended that you visit a NISSAN dealer.
High-voltage parts and harnesses on the
hybrid vehicles emit approximately the
same amount of electromagnetic waves
as the conventional gasoline-powered ve-
hicles or home electronic appliances de-
spite their electromagnetic shieldings.
Charging the Li-ion battery while driving is
important. The vehicle cannot run if the Li-
ion battery is discharged. When in the N
(Neutral) position and while both the accel-
erator pedal and the brake pedal are not
depressed, the Li-ion battery does not re-
charge. Leaving the transmission in the N
(Neutral) position, while both the accelerator
pedal and the brake pedal are not de-
pressed for an extended period of time, may
discharge the Li-ion battery and the hybrid
system may automatically be turned off.
HEV OverviewHEV-13

1. Vent (P. 4-29)
2. Headlight/fog light (if soequipped)/turn signal switch
(P. 2-46)
3. Meters and gauges (P. 2-4) Warning and indicator lights
(P. 2-10)
Vehicle information display (P. 2-21)
4. Wiper and washer switch (P. 2-43) Rear wiper washer switch (P. 2-43)
5. Push-button ignition switch
(P. 5-14)
6. Hazard warning flasher switch
(P. 6-2)
7. Radio* Navigation system*
(if so equipped)
8. Front passenger supplemental air
bag (P. 1-45)
9. Glove box (P. 2-60)
10. Heater and air conditioning
controls (P. 4-30)
11. Power outlet (P. 2-57)
12. Shif t lever (P. 5-19)
13. Auxiliary jack* USB port*
14. Front passenger air bag status
light (P. 1-45)
LII2516
INSTRUMENT PANEL
0-6Illustrated table of contents

WARNING
∙ Always route the shoulder belt overyour shoulder and across your chest.
Never put the belt behind your back,
under your arm or across your neck.
The belt should be away from your
face and neck, but not falling off your
shoulder.
∙ Position the lap belt as low and snug as possible AROUND THE HIPS, NOT
THE WAIST. A lap belt worn too high
could increase the risk of internal inju-
ries in an accident. ∙ Be sure the seat belt tongue is se-
curely fastened to the proper buckle.
∙ Do not wear the seat belt inside out or twisted. Doing so may reduce its
effectiveness.
∙ Do not allow more than one person to use the same seat belt.
∙ Never carry more people in the vehicle than there are seat belts.
∙ If the seat belt warning light glows continuously while the ignition is
placed in the ON position with all
doors closed and all seat belts fas-
tened, it may indicate a malfunction in
the system. Have the system checked.
It is recommended that you visit a
NISSAN dealer for this service.
∙ No changes should be made to the seat belt system. For example, do not
modif y the seat belt, add material, or
install devices that may change the
seat belt routing or tension. Doing so
may affect the operation of the seat
belt system. Modif ying or tampering
with the seat belt system may result
in serious personal injury. ∙ Once seat belt pretensioner(s) have
activated, they cannot be reused and
must be replaced together with the
retractor. It is recommended that you
visit a NISSAN dealer for this service.
∙ All seat belt assemblies, including re- tractors and attaching hardware,
should be inspected af ter any colli-
sion. It is recommended that you visit
a NISSAN dealer for this service.
NISSAN recommends that all seat belt
assemblies in use during a collision be
replaced unless the collision was mi-
nor and the belts show no damage
and continue to operate properly.
Seat belt assemblies not in use during
a collision should also be inspected
and replaced if either damage or im-
proper operation is noted.
∙ All child restraints and attaching hardware should be inspected af ter
any collision. Always follow the re-
straint manufacturer’s inspection in-
structions and replacement recom-
mendations. The child restraints
should be replaced if they are
damaged.
SSS0014
Safety—Seats, seat belts and supplemental restraint system1-13

9. Check to make sure the child restraintis properly secured prior to each use. If
the seat belt is not locked, repeat
steps 2 through 8.
10. If the child restraint is installed in thefront passenger seat, place the ignition
switch in the ON position. The front
passenger air bag status light
should illuminate. If this light is not illu-
minated refer to “Front passenger air
bag and status light” in this section.
Move the child restraint to another
seating position. Have the system
checked. It is recommended that you
visit a NISSAN dealer for this service.
Af ter the child restraint is removed and the
seat belt is fully retracted, the ALR mode
(child restraint mode) is canceled.
1Top tether strap
2Anchor point
Installing top tether strap
The child restraint top tether strap must be
used when installing the child restraint with
seat belts.
First, secure the child restraint with the seat
belt.
Forward-facing – step 10
WRS0475
Rear seats
LRS2714
1-40Safety—Seats, seat belts and supplemental restraint system

3. The booster seat should be positionedon the vehicle seat so that it is stable.
If necessary, adjust or remove the head
restraint/headrest to obtain the cor-
rect booster seat fit. If the head
restraint/headrest is removed, store it
in a secure place. Be sure to reinstall
the head restraint/headrest when
the booster seat is removed. For ad-
ditional information, refer to "Head
restraints/headrests" in this section.
If the seating position does not have
an adjustable head restraint/headrest
and it is interfering with the proper booster seat fit, try another seating
position or a different booster seat.
4. Position the lap portion of the seat belt low and snug on the child’s hips. Be
sure to follow the booster seat manu-
facturer’s instructions for adjusting the
seat belt routing.
5. Pull the shoulder belt portion of the seat belt toward the retractor to take
up extra slack. Be sure the shoulder
belt is positioned across the top,
middle portion of the child’s shoulder.
Be sure to follow the booster seat
manufacturer’s instructions for adjust-
ing the seat belt routing.
6. Follow the warnings, cautions and in- structions for properly fastening a seat
belt shown in “Three-point type seat
belt with retractor” in this section. 7. If the booster seat is installed in the
front passenger seat, place the ignition
switch in the ON position. The front pas-
senger air bag status light
may or
may not illuminate, depending on the
size of the child and the type of booster
seat being used. For additional infor-
mation, refer to “Front passenger air
bag and status light” in this section.
Front passenger position
LRS0454WRS0475
1-44Safety—Seats, seat belts and supplemental restraint system