2019 MITSUBISHI ASX Owner's Manual (in English)

NOTEzIf the ignition switch or the operation mode
is left in ACC, the accessory power will au- tomatically turn off after a certain period of
time and you will no longer be able to use
the Bluetooth

PICK-UP button
zPress this button when an incoming call
is received to answer the telephone.
z When another call is received during a
call, press this button to put the first call- er on hold and talk to the new caller.

4.The voice guide will say “Select a lan-
guage: English, French, Spanish, Italian,
German, Dutch, Portuguese or Russian” Say the desired language. (Example: Say“English.”)
5. The voice guide will say “English
(French, Spanish, Italian, German, Dutch, Portuguese or Russian) selected.Is this correct?” Say “Yes.”
Answer “No” to return to Step 4.NOTEz The voice guide will repeat the same mes-
sage twice. The first message is in the cur-rent language, and the second message is inthe selected language.
z If many entries are registered in the vehicle
phone book, changing the language will take longer.
z Changing the language deletes the mobile
phone book imported to the Bluetooth

4.The voice guide will say “Password is
disabled. Would you like to enable it?”
Answer “Yes.”
Answer “No” to cancel the setting of the
password and return to the main menu.
5. The voice guide will say “Please say a 4-
digit password. Remember this pass-
word. It will be required to use this sys-
tem”.
Say a 4-digit number which you want to set as a password.
6. For confirmation purposes, the voice
guide will say “Password <4-digit pass-
word>. Is this correct?” Answer “Yes.”
Answer “No” to return to the password input in Step 5.
7. When the registration of the password is
completed, the voice guide will say “Password is enabled” and the systemwill return to the main menu.NOTEz Password will be required to access the sys-
tem after the next ignition cycle.NOTEz It is required for a little time after engine
stop that the entered password is actually re-corded in the system.
If the ignition switch or the operation mode is made to ACC or ON or the engine is star-ted immediately after engine stop, there is a
case when the entered password is not recor- ded in the system. At this time, please try to
enter the password again.
Entering the password
If a password has been set and the security
function is enabled, the voice guide will say “Hands-free system is locked. State the pass-word to continue” when the SPEECH button
is pressed to enter voice recognition mode.
Say the 4-digit password number to enter the
password.
If the entered password is wrong, the voice
guide will say “<4- digit password>, Incor-
rect password. Please try again”. Enter the correct password.
NOTEz You can re-enter the password as many
times as you want.
z If you have forgotten your password, say
“Cancel” to quit the voice input mode and then check with a MITSUBISHI MOTORS
Authorized Service Point.Disabling the password
Use the following procedure to turn off the
security function by disabling the password.
NOTEz System must be unlocked to disable the
password.
1. Press the SPEECH button.
2. Say “Setup”.
3. Say “Password.”
4. The voice guide will say “Password is
enabled. Would you like to disable it?”
Answer “Yes.”
Answer “No” to cancel the disabling of
the password and return to the main menu.
5. When the disabling of the password is
completed, the voice guide will say “Password is disabled” and the system
will return to the main menu.
Speaker enrollment function
The Bluetooth

You can turn a voice model registered with
the speaker enrollment function on and off
whenever you want.Speaker enrollment
It takes about 2 to 3 minutes to complete the
speaker enrollment process.
To ensure the best results, run through the
process while in the driver

3.If you have completed a speaker enroll-
ment process once already, the voiceguide will say either “Enrollment is ena-
bled. Would you like to disable or re-
train?” or “Enrollment is disabled. Would you like to enable or retrain?”
4. When enrollment is “enabled”, the voice
model is on; when enrollment is “disa-
bled”, the voice model is off. Say the command that fits your needs.
Say “Retrain” to start the speaker enroll-
ment process and recreate a new voice model. (Refer to “Speaker enrollment”
on page 7-51.)Connecting the Bluetooth

number said is acceptable. Answer
“Yes.”
Answer “No” to return to pairing code selection.NOTEz Some Bluetooth

NOTEzThe following procedure ( to ) can also
be used instead of saying “Pair Device.” Re- place this step 3 with the following proce-dure if you prefer.
Say “Setup.”
Say “Pairing Options.”
The voice guide will say “Select one of
the following: pair, edit, delete, or list.”
Say “Pair.”
z If 7 devices have already been paired, the
voice guide will say “Maximum devicespaired” and then the system will end the
pairing process. To register a new device, delete one device and then repeat the pairing
process.
(Refer to “Selecting a device: Deleting a de- vice” on page 7-55.)
4. The voice guide will say “Start pairing
procedure on the device. See the device manual for instructions.” and then willsay “The pairing code is <pairing
code>.”
NOTEz Some Bluetooth