2019 MERCEDES-BENZ S-CLASS CABRIOLET warning

Only use tires, wheels and accessories
that
ha ve been checked and recommended by
Mercedes-Benz. *
NO
TERisk todriving saf ety from retrea‐
ded tires Re
treaded tires are nei ther tested nor recom‐
mended byMercedes-Benz, since pr evious
damage cannot alw ays be de tected on
re treaded tires.
Fo rth is reason driving saf ety cannot be guar‐
anteed. #
Do not use used ti res if you ha veno
information about their pr evious usage. *
NO
TEPossible damage towheels or tires
when driving over obs tacles Large wheels ha
vea lo wer tire section width.
The lo werth e tire section width, the greater
is therisk of damage towheels or tires when
driving over obs tacles. #
Avoid obs tacles or drive pa rticular ly
carefully. *
NO
TEDama getoelectronic component
parts from the use of tire-mounting tools Ve
hicles with a tire pressure monitoring
sy stem: Electronic component parts are
located in the wheel. Tire -mounting tools
should not be used in the area of theva lve.
This could otherwise damage the electronic
component parts. #
Have the tires changed at a qualified
specialist workshop onl y. *
NO
TEDama getosummer tires at low
ambient temp eratures At
low ambient temp eratures, tears could
fo rm when driving with summer tires, caus‐
ing permanent damage tothe tires. #
Attemp eratures below 45 °F (7 °C),
use M+S tires . Ac
cessory pa rts th at are not appr ovedfo ryo ur
ve hicle byMercedes-Benz or are not being used
cor rectly can impair the operating saf ety.
Before pu rchasing and using non-appr oved
accesso ries, visit a qualified specialist workshop
and inquire about:
R Suitability
R Legal stipulations
R Factory recommendations &
WARNING Risk of accident wi thhigh
per form ance tires
The special tire tread in combination with the
optimized tire compound means that therisk
of skidding or hydroplaning on wetro ads is
inc reased.
In addition, the tire grip is greatly reduced at
a low outside temp erature and tire running
te mp erature. #
Switch on the ESP ®
and adapt your
driving style accordingly. #
Use M+S tire at outside temp eratures
of less than 10 °C (50 °F). Wheels and tires
397

Obser
vethefo llowing when selecting, ins talling
and replacing tires:
R Only use tires and wheels of the same type
(summer tires, winter tires, MOEx tended
tires) and the same make.
R Only ins tall wheels of the same size on one
axle (left and right).
It is only permissible toins tall a dif fere nt
wheel size in theeve nt of a flat tire in order
to drive tothe specialist workshop.
R Only ins tall tires of the cor rect size onto the
wheels.
R Vehicles with a tire pressure monitoring
sy stem: All ins talled wheels must be equip‐
ped with functioning sensors forth e tire
pressure monitoring sy stem.
R Attemp eratures below 45 °F (7 °C), use win‐
te r tires or all-season tires mar ked M+S for
all wheels.
Wi nter tires bearing the004D snowflake sym‐
bol in addition tothe M+S marking pr ovide
th e best possible grip in wintry road condi‐
tions. R
For M+S tires, only use tires with the same
tread.
R Obser vethe maximum permissible speed for
th e M+S tires ins talled.
If th is is below theve hicle's maximum speed,
th is must be indicated byan appropriate
label in the driver's field of vision.
R Break in new tires at moderate speeds for
th efirs t 60 miles (100 km).
R Replace the tires af ter six years at the latest,
re ga rdless of wear.
R When replacing with tires that do not fea‐
ture run-flat characteristics: vehicles with
MOExtended tires are not equipped with a
TIREFIT kit at thefa ctor y.Equip theve hicle
with a TIREFIT kit af terre placing with tires
th at do not feature run-flat characteristics,
e.g. winter tires.
Fo r more information on wheels and tires, con‐
tac t a qualified specialist workshop.
Be sure toalso obse rveth efo llowing fur ther
re lated subjects:
R Notes on tire pressure (→ page377) R
Tire and Loading In form ation placard
(→ page 384)
R Tire size designation, load-beari ng capacity,
speed rating and load ind ex (→page 391)
R Tire pressure table (→ page379) Note
s onrotating wheels &
WARNING Risk of inju rythro ugh dif fer‐
ent wheel sizes
Inter changing the front and rear wheels if the
wheels or tires ha vediffere nt dimensions
may se verely impair the driving characteris‐
tics.
The wheel brakes or wheel suspension com‐
ponents may also be damaged. #
Rotate front and rear wheels on lyifthe
wheels and tires are of the same dimen‐
sions. 398
Wheels and tires

#
Using the lug wrench, loosen the wheel bolts
on the wheel you wish tochange byabout
one full turn. Do not unscr ewthe bolts com‐
ple tely. Po
sition of jack support points &
WARNING Risk of inju ryfrom incor rect
positioning of the jack
If yo u do not position the jack cor rectly at
th e appropriate jacking point of theve hicle,
th e jack could tip with theve hicle raised. #
Only position the jack at the appropri‐
ate jacking point of theve hicle. The
base of the jack must be positioned ver‐
tically under the jacking point of the
ve hicle. *
NO
TEVehicle damage from the jack If
yo u do not position the jack cor rectly at
th e appropriate jack support point of the
ve hicle, the jack could tip over with theve hi‐
cle raised. #
The jack is designed exclusively for
jacking up theve hicle at the jack sup‐
port points. #
Take thera tchet out of the tire-change tool
kit and place it on the he xagon nut of the
jack so that the letters "AUF" are visible. 402
Wheels and tires

&
WARNING Risk of accident from losing a
wheel
Oiled, greased or damaged wheel bolt/wheel
nut thre ads or wheel hub/wheel mounting
bolt thre ads can cause the wheel bolts/
wheel nuts tocome loose.
As a result, you could lose a wheel while driv‐
ing. #
Never oil or grease theth re ads. #
Intheeve nt of damage totheth re ads,
con tact a qualified specialist workshop
immediatel y. #
Have the damaged wheel bolts or dam‐
aged hub thre ads replaced. #
Do not continue driving. #
Obser vethe information on thech oice of
tires (→ page 396).
Fo r tires with a specified direction of rotation, an
ar row onthe side wall of the tire indicates the
cor rect di rection of rotation. Obse rveth e direc‐
tion of rotation when ins talling. #
Slide the wheel tobe mounted onto the
alignment bolt and push it on. &
WARNING Risk of inju ryfrom tightening
wheel bolts and nuts
If yo u tighten the wheel bolts or wheel nuts
when theve hicle is raised, the jack could tip. #
Only tighten wheel bolts or wheel nuts
when theve hicle is on the ground. #
Be sure toobser vethe instructions and
saf ety no tes on "Changing a wheel"
(→ page 396). #
For saf etyre asons, on lyuse wheel bolts
which ha vebeen appr ovedby Mercedes-
Benz and forth e wheel in question.
* NO
TEDama getopaintwork of the wheel
ri m when scr ewing on thefirs t wheel bolt If
th e wheel has too much play when scr ew‐
ing in thefirs t wheel bolt, the wheel rim paint
can be dama ged. #
Press the wheel firm lyagainst the
wheel hub when scr ewing on thefirst
wheel bolt. #
Tighten the wheel bolts evenly in a diagonal
pattern in the order indicated until they are
fi nger-tight. #
Unscr ew the alignment bolt. #
Tighten the last wheel bolt until it is finger-
tight. #
Lowe rth eve hicle (→ page 404). Lo
weri ngtheve hicle af ter a wheel change Re
quirements:
R The new wheel has been ins talled
(→ page 403). #
Place thera tchet onto the he xagon nut of the
jack so that the letters "AB" are visible. #
Tolowe r the vehicle: turnthera tchet of the
jack counter-clo ckwise. 404
Wheels and tires

#
Tighten the wheel bolts evenly in a diagonal
pattern in the order indicated (1 to5 ).
Specified tightening torq ue: 111 lb-ft
(150 Nm). &
WARNING Risk of inju rythro ugh incor‐
re ct tigh tening torque
The wheels could come loose if the wheel
bolts or wheel nuts are not tightened tothe
prescribed tightening torque. #
Makesure the wheel bolts or wheel
nuts are tightened tothe prescribed
tightening torque. #
Ifyo u are not sure, do not mo vethe
ve hicle. Consult a qualified specialist
wo rkshop and ha vethe tightening tor‐
qu ech ecked immediately. #
Check the tire pressure of the newly moun‐
te d wheel and adjust according ly. #
Vehicles with a tire pressure monitoring
sy stem: Restart the tire pressure monitoring
sy stem (→ page 383).
Make sure toobser vethefo llowing fur ther rela‐
te d subjec t:
R Notes on tire pressure (→ page377) Wheels and
tires405

Note
s ontech nical data
Mercedes-AMG vehicles: observeth e no tes in
th e Supplement. Otherwise, you may not recog‐
nize dangers.
The da tastated on lyapplies tovehicles with
st andard equipment. You can obtain fur ther
information from an authorized Mercedes-Benz
Center. Ve
hicle electronics Tw
o-w ayradios Note
s on installing two-w ayradios &
WARNING Risk of accident due to
improper workon two-w ayradios
The elect romagnetic radiation from two-w ay
ra dios can inter fere with the on-board elec‐
tronics if RF transmit ters are manipulated or
re trofitted inco rrectly.
This could jeopardize the operating saf ety of
th eve hicle. #
You should ha veall workon electrical
and electronic components car ried out
at a qualified specialist workshop. &
WARNING Risk of accident from incor‐
re ct ope ration of two-w ayradios
If yo u operate two- wayra dios incor rectly in
th eve hicle, the electromagnetic radiation
could inter fere with the on-board electronics,
e.g.:
R ifth e two-w ayradio is not connec tedto
an exterior antenna
R ifth eex terior antenna is not cor rectly
mounted or is not of low reflection
This could jeopardies the operating saf ety of
th eve hicle. #
Have the lo w-reflection exterior
antenna ins talled at a qualified special‐
ist workshop. #
When operating two-w ayradios in the
ve hicle, alw ays connect them tothe
lo w- reflection exterior antenna. *
NO
TEInva lidation of the operating per‐
mit due tofailure tocomply wi th the
instructions for ins tallation and use The operating permit may be in
validated if
th e instructions for ins tallation and use of
two-w ayradios are not obser ved. #
Only use appr oved frequency bands. #
Obser vethe maximum permissible out‐
put po wer in these frequency bands. #
Only use appr oved antenna positions. 406
Tech nical da ta

Operating
fluids Note
s on operating fluids Mercedes-AMG
vehicles: observeth e no tes in
th e Supplement. Otherwise, you may failto rec‐
ognize dangers. &
WARNING Risk of inju ryfrom operating
fl uids harmful to your health
Operating fluids may be poisonous and harm‐
ful to yo ur health. #
Obser vethete xt on the original con‐
ta iners when using, storing or disposing
of operating fluids. #
Alw aysst ore operating fluids sealed in
th eir original conta iners.#
Alw ayske ep children away from operat‐
ing fluids. &
WARNING Risk offire or explosion from
fuel
Fu els are highly flammable. #
Fire, open flames, smoking and creation
of spar ksmust be avoided. #
Swit choff the ignition and, if available,
th est ationary heater, before and while
re fueling theve hicle. &
WARNING Risk of inju ryfrom fuels
Fu els are poisonous and hazardous to your
health. #
Do not swallow fuel or let it come into
contact with skin, eyes or clo thing. #
Do not inhale fuel vapor. #
Keep children away from fuel. #
Keep doors and windo wsclosed du ring
th ere fueling process.
If yo u or other people come into contact with
fuel, obser vethefo llowing: #
Immediately rinse fuel off your skin with
soap and water. #
If fuel comes into contact with your
ey es, immediately rinse them thor‐ oughly with clean
water.Seek medical
attention immediately. #
Ifyo u swallow fuel, seek medical atten‐
tion immediatel y.Do not induce vomit‐
ing. #
Change immediately out of clo thing that
has come into con tact wi thfuel. +
ENVIRONMENTAL
NOTEEnvironmental
pollution caused byenvironmen tally ir re‐
sponsible disposal #
Dispose of operating fluids in an envi‐
ro nmentally responsible manner. Operating
fluids include thefo llowing:
R Fuels
R Lubricants
R Coolant
R Brake fluid
R Windshield washer fluid
R Climate cont rol sy stem refrigerant 41 0
Tech nical da ta

*
NO
TEEngine dama gecaused byan
incor rect oil filter, incor rect oil or addi‐
tives #
Do not use engine oils or oil filters other
th an those which meet the specifica‐
tions necessary forth e prescribed
service inter vals. #
Do not alter the engine oil or oil filter in
order toachie velonger change inter vals
th an presc ribed. #
Do not use additives. #
Have the engine oil changed af terthe
prescribed inter vals. Mercedes-Benz
recommends that you ha vethe
oil change car ried out at a qualified specialist
wo rkshop.
Fu rther information on engine oil and oil filters is
av ailable at thefo llowing locations:
R Inthe Mercedes-Benz Specifications for
Operating Fluids byentering the designation:
- Athttp://be vo.mercedes-benz.com
- Inthe Mercedes-Benz BeVo app R
at a qualified specialist workshop
Quality and capacity of engine oil
MB-F reigabe or MB-Appr oval Model
MB-Freigabe or MB-
Appr oval
S 560 229.52, 229.61 The
following values referto an oil change,
including the oil filter.
Capacity Model
Capacity
S 560 9.5 US qt (9.0 liters) Note
s on brake fluid Obser
vethe no tes on operating fluids
(→ page 410). &
WARNING Risk of an accident due to
va por poc kets form ing in the brake sys‐
tem
The brake fluid constantly absorbs moisture
from the air. This lo wersthe boiling point of
th e brake fluid. If the boiling point is too lo w,
va por poc kets may form inthe brake sy stem
when the brakes are applied hard.
This causes the braking ef fect to be
impaired. #
Have the brake fluid rene we d at the
specified inter vals. Ha
ve the brake fluid regularly replaced at a
qu alified specialist workshop.
Only use brake fluid appr ovedby Mercedes-Benz
according toMB-F reigabe or MB-Appr oval 33 1.0.
Yo u can obtain fur ther information on brake fluid
in thefo llowing places:
R inthe Mercedes-Benz Specifications for
Operating Fluids
- at http://be vo.mercedes-benz.com
- inthe Mercedes-Benz BeVo App Te
ch nical da ta413