2019 MAZDA MODEL CX-30 transmission

xThe SBS-R system will operate under
the following conditions.
xThe engine is running.xThe shift lever (manual
transmission vehicle) or the
selector lever (automatic
transmission vehicle) is in the R
(reverse) position.
xi-ACTIVSENSE warning indication/
warning light is not displayed in the
multi-information display.
xThe vehicle speed is between
about 2 to 8 km/h (2 to 4 mph).
xThe SBS-R is not turned off.xThe DSC is not malfunctioning.xIn the following cases, the rear
ultrasonic sensor and rear camera
cannot detect obstructions and the
SBS-R may not operate.
xThe height of the obstruction is
low such as low walls or trucks
with low loading platforms.
xThe height of the obstruction is
high such as trucks with high
loading platforms.
xThe obstruction is small.xThe obstruction is thin such as a
signpost.
xThe surface of the obstruction is
not pointed vertically relative to
the vehicle.
xThe obstruction is soft such as a
hanging curtain or snow stuck to a
vehicle.
xThe obstruction is shaped
irregularly.
xThe obstruction is extremely close.xIn the following cases, the rear
ultrasonic sensor and rear camera
cannot detect obstructions correctly
and the
SBS-R may not operate.
xSomething is stuck on the bumper
near a rear ultrasonic sensor.
xThe brake or accelerator pedal is
operated.
xThere is another obstruction near
one obstruction.
xDuring inclement weather such as
rain, fog and snow.
xHigh or low humidity.xHigh or low temperaturesxStrong winds.xThe path of travel is not flat.xHeavy luggage is loaded in the
luggage compartment or on the
rear seat.
xObjects such as a wireless aerial,
fog light, or illuminated number
plate is installed near a rear
ultrasonic sensor.
xThe orientation of a rear ultrasonic
sensor has deviated for reasons
such as a collision.
xThe vehicle is affected by other
sound waves such as the horn,
engine noise, ultrasonic sensor of
another vehicle.
xIn the following cases, a rear
ultrasonic sensor and rear camera
may detect something as a target
obstruction which could cause the
SBS-R system to operate.
xDriving on a steep slope.xWheel blocks.xHanging curtains, gate poles such
as at toll gates and railroad
crossing.
xWhen travelling near objects such
as foliage, barriers, vehicles, walls,
and fences along a road.
xWhen driving off-road in areas
where there is grass and forage.
xWhen passing through low gates,
narrow gates, car washing
machines, and tunnels.
xA trailer is connected.xA bright light source such as
sunlight hits the rear camera.
xThe surroundings are dark.
When Driving
i-ACTIVSENSE
4-179

xAn exterior accessory such as a
bicycle carrier is installed around a
rear ultrasonic sensor.
x(Manual transmission)
If the vehicle is stopped by the SBS-R
operation and the clutch pedal is not
depressed, the engine stops.
xWhen the system operates, the user
is notified by the multi-information
display.
xThe collision warning beep sounds
intermittently while the SBS-R brake
is operating.
xIf the vehicle is stopped by the SBS-R
operation and the brake pedal is not
depressed, displaying in meter
“Emergency Braking Activated.
Depress Brake Pedal to Hold Stop”,
after about 2 seconds and the SBS-R
brake is automatically released.
xIf a Mazda genuine trailer hitch is
used, the SBS-R is automatically
turned off.
xTurn off the SBS-R system while
pulling a trailer or while an accessory
such as a bicycle carrier is installed to
the rear of the vehicle.
▼Collision Warning
If there is a possibility of a collision, the
collision warning sound is activated
continuously and a warning is
displayed on the active driving display
and the multi-information display.
Multi-information display
1. “BRAKE!” message is displayed

Active driving display
1. “BRAKE!” message is displayed
▼Stopping the Smart Brake Support
[Rear] (SBS-R) System Operation
The SBS-R can be changed to
inoperable.
Refer to the Settings section in the
Mazda Connect Owner's Manual.
When the SBS-R is cancelled, the SBS
OFF indicator light turns on.
NOTE
xWhen the ignition is switched OFF
while the SBS-R is cancelled, the
SBS-R is automatically enabled the
next time the ignition is switched
ON.
xWhen the SBS-R is cancelled, the
Smart Brake Support [Rear Crossing]
(SBS-RC) is also cancelled.
When Driving
i-ACTIVSENSE
4-180

Smart Brake Support
[Rear Crossing] (SBS-RC)
*
▼Smart Brake Support [Rear
Crossing]
(SBS-RC)
The SBS-RC is a system designed to
assist the driver in avoiding collisions
and to reduce damage in the event of
a collision by applying the brakes if
there is the possibility of collision with
a vehicle approaching from the rear
while you are reversing out of parking
space.
The SBS-RC system detects vehicles
approaching from the rear left and
right sides of the vehicle, and the rear
of the vehicle while the vehicle is being
reversed out of a parking space, the
system reduces damage in the event of
a collision by operating the brake
control when the system determines
that a collision is unavoidable.
SBS-RC operation
1. The SBS-RC system operates when
the shift lever (manual
transmission) or the selector lever
(automatic transmission) is shifted
to the reverse (R) position.
2. If there is the possibility of a
collision with an approaching
vehicle, the SBS-RC system applies
brake and displays “BRAKE!” on the
active driving display and the
multi-information display.
WARNING
Always check the surrounding area
visually before actually putting the
vehicle in reverse:
The system is only designed to assist
you in backing out of the lot when
putting the vehicle in reverse. Due to
certain limitations with the operation
of this system, the SBS-RC system may
not operate brake or it might be
delayed even though a vehicle is
behind your vehicle. Always make it
your responsibility as a driver to check
the rear.
Do not rely completely on the SBS-RC
system:
¾The
SBS-RC system is only designed
to reduce damage in the event of a
collision. Over reliance on the system
leading to the accelerator pedal or
brake pedal being mistakenly
operated could result in an accident.
¾The SBS-RC system operates in
response to a vehicle. The system
does not operate in response to
obstructions such as a wall,
pedestrians, 2-wheeled vehicles, or
animals.
To assure the correct operation of the
SBS-RC, heed the following cautions.
¾Do not apply a sticker to a rear radar
and rear camera. Otherwise, the rear
radar and rear camera may not be
able to detect vehicles or
obstructions which could result in an
accident.
¾Do not disassemble a rear radar and
rear camera.
When Driving
i-ACTIVSENSE
*Some models.4-181

¾If cracks or damage caused by flying
gravel or debris is visible around a
rear radar and rear camera, stop
using the SBS-RC system
immediately and have your vehicle
inspected by an expert repairer (we
recommend an Authorised Mazda
Repairer). If the vehicle continues to
be driven with cracks or scratch
marks left around an ultrasonic
sensor, the system may operate
unnecessarily and cause an
unexpected accident.
Refer to Stopping the Smart Brake
Support [Rear Crossing] (SBS-RC)
System Operation on page 4-184.
¾Consult an expert repairer (we
recommend an Authorised Mazda
Repairer) for rear bumper
replacement.
Do not modify the suspension:
If the vehicle height or inclination is
changed, the
SBS-RC system may not
operate correctly because it cannot
detect obstructions correctly.
Do not apply a strong force to a rear
radar and rear camera:
When washing the vehicle, do not
spray highly pressurised water against a
rear radar and rear camera, or rub it
strongly. In addition, do not hit the rear
bumper forcefully when loading and
unloading cargo. Otherwise, the
sensors may not detect obstructions
correctly which could cause the
SBS-RC system to not operate
normally, or it could operate
unnecessarily.
NOTE
xThe SBS-RC system will operate
under the following conditions.
xThe engine is running.
xThe shift lever (manual
transmission vehicle) or the
selector lever (automatic
transmission vehicle) is in the R
(reverse) position.
xi-ACTIVSENSE warning indication/
warning light is not displayed in the
multi-information display.
xThe vehicle speed is under about
10 km/h (6 mph).
xThe vehicle speed of an
approaching vehicle is about 3
km/h (2 mph) or faster.
xThe SBS-R is not turned off.xThe DSC is not malfunctioning.xIn the following cases, the
i-ACTIVSENSE warning indication/
warning light turns on and operation
of the system is stopped. If the
i-ACTIVSENSE warning indication/
warning light remains illuminated,
have the vehicle inspected at an
expert repairer (we recommend an
Authorised Mazda Repairer) as soon
as possible.
xSome problem with the system
including the SBS-RC system.
xA large deviation in the installation
position of a rear side radar sensor
on the vehicle has occurred.
xThere is a large accumulation of
snow or ice on the rear bumper
near a rear side radar sensor.
xDriving on snow-covered roads for
long periods.
xThe temperature near the radar
sensors becomes extremely hot
due to driving for long periods on
slopes during the summer.
xThe battery voltage has decreased.xUnder the following conditions, the
rear side radar sensor cannot detect
target objects or it may be difficult to
detect them.
When Driving
i-ACTIVSENSE
4-182

x(Manual transmission)
If the vehicle is stopped by the
SBS-RC operation and the clutch
pedal is not depressed, the engine
stops.
xWhen the system operates, the user
is notified by the multi-information
display.
xThe collision warning beep sounds
intermittently while the SBS-RC
brake is operating.
xIf the vehicle is stopped by the
SBS-RC operation and the brake
pedal is not depressed, displaying in
meter “Emergency Braking Activated.
Depress Brake Pedal to Hold Stop”,
after about 2 seconds and the
SBS-RC brake is automatically
released.
xIf a Mazda genuine trailer hitch is
used, the SBS-RC is automatically
turned off.
▼Collision Warning
If there is a possibility of a collision, the
collision warning sound is activated
continuously and a warning is
displayed on the active driving display
and the multi-information display.
Multi-information display
1. “BRAKE!” message is displayed

Active driving display
1. “BRAKE!” message is displayed
▼Stopping the Smart Brake Support
[Rear Crossing]
(SBS-RC) System
Operation
The SBS-RC can be changed to
inoperable.
Refer to the Settings section in the
Mazda Connect Owner's Manual.
When the SBS-RC is cancelled, the SBS
OFF indicator light turns on.
NOTE
xWhen the ignition is switched OFF
while the SBS-RC is cancelled, the
SBS-RC is automatically enabled the
next time the ignition is switched
ON.
xWhen the SBS-RC is cancelled, the
Smart Brake Support [Rear] (SBS-R)
is also cancelled.
When Driving
i-ACTIVSENSE
4-184

xThe shift lever/selector lever is in a position other than R.

Display switching
The displayed screen can be changed each time the 360°view monitor switch is
pressed.
1. Top view/Front view
2. Top view/Front wide view
3. Side view
4. Home screen
NOTE
xWhen the shift lever/selector lever is in R position, the displayed screen does not
switch to the top view/front view, top view/front wide view, or the side view.
xDisplay of the top view/front view, top view/front wide view, or the side view
stops even with the display conditions met if any of the following conditions
occurs.
xWhen a switch around the commander knob is pressed.x(Manual transmission)
The parking brake is applied.
When Driving
i-ACTIVSENSE
4-193

x(Automatic transmission)
The selector lever is shifted to P position (displayed when the selector lever is in
a position other than P).
x(Displayed when vehicle speed is less than 15 km/h (9.3 mph))
x4 minutes and 30 seconds have passed.xThe vehicle speed is about 15 km/h (9.3 mph) or faster.x(Displayed when the vehicle speed is about 15 km/h (9.3 mph) or faster)
xThe vehicle speed is about 15 km/h (9.3 mph) or faster after 8 seconds have
passed since pressing the 360°View Monitor switch.
xFour minutes and 22 seconds have passed from the point when the vehicle
speed was less than 15 km/h (9.3 mph) after 8 seconds have passed since
pressing the 360°View Monitor switch.
xThe 360°View Monitor settings can be changed as follows.
Refer to the Settings section in the Mazda Connect Owner's Manual.
xAutomatic display of the 360°View Monitor when the ultrasonic senor detects
an obstruction.
xAutomatic display of the 360°View Monitor when the ignition is switched ON.xScreen priority level when the system launches.
Top view/Rear view, Top view/Rear wide view
The top view/rear view, top view/rear wide view displays when all of the following
conditions are met.
xThe ignition is switched ON.xShift lever/selector lever is in R position.
Display switching
The displayed screen can be changed each time the 360°view monitor switch is
pressed.
1. Top view/Rear view
2. Top view/Rear wide view
NOTE
xThe top view/rear view and top view/rear wide view automatically display
whether or not the 360°View Monitor switch is turned on or off when shifting the
shift lever/selector lever to R position.
xThe top view/rear view and top view/rear wide view displays the previously
displayed screen.
When Driving
i-ACTIVSENSE
4-194

Cruise Set Indication (Green)
The indication turns on (green) when a
cruising speed has been set.
▼Activation/Deactivation
WARNING
Always turn off the cruise control
system when it is not in use:
Leaving the cruise control system in an
activation-ready state while the cruise
control is not in use is dangerous as the
cruise control could unexpectedly
activate if the activation button is
accidentally pressed, and result in loss
of vehicle control and an accident.
NOTE
When the ignition is switched OFF, the
system status before it was turned off is
maintained. For example, if the
ignition is switched OFF with the cruise
control system operable, the system
will be operable when the ignition is
switched ON the next time.
Activation
To activate the system, press the cruise
switch. The cruise standby indication
(white) turns on.
Deactivation
To deactivate the system, press the
cruise switch again.
The cruise standby indication (white)
turns
off.
▼To Set Speed
1. Activate the cruise control system
by pressing the cruise switch. The
cruise standby indication (white)
turns on.
2. Accelerate to the desired speed,
which must be more than 25 km/h
(16 mph).
3. Adjust the system to the desired
vehicle speed using the accelerator
pedal. Press the RES switch up (SET
+) or down (SET-) to start cruise
control. The cruise control
indication (green) in the instrument
cluster turns on at the same time.
Quickly release the switch when the
cruise control indication (green)
turns on.
NOTE
xIf the RES switch is operated up (SET
+) or down (SET-) while the vehicle
speed is between 25 km/h (16 mph)
and 30 km/h (19 mph), the set
speed is set to 30 km/h (19 mph).
xThe cruise control speed setting
cannot be performed under the
following conditions:
xAny of the doors is opened.xThe driver's seat belt is unfastened.xThe brake pedal is depressed.xThe parking brake is applied.x(Automatic transmission)
The selector lever is in the P or N
position.
x(Manual transmission)
The shift lever is in the neutral
position.
xOn a steep grade, the vehicle may
momentarily slow down while
ascending or speed up while
descending.
xThe cruise control will cancel if the
vehicle speed decreases below 20
km/h (12 mph) when the cruise
control is activated, such as when
climbing a steep grade.
When Driving
Cruise Control
4-229