2019 MAZDA MODEL CX-30 ignition

Sunroof*
▼Sunroof
The sunroof can be opened or closed
when operating the overhead tilt/slide
switch at the front seats.
WARNING
Do not let passengers stand up or
extend part of the body through the
open sunroof while the vehicle is
moving:
Extending the head, arms, or other
parts of the body through the sunroof
is dangerous. The head or arms could
hit something while the vehicle is
moving. This could cause serious injury
or death.
Never allow children to play with the
tilt/slide switch:
The tilt/slide switch would allow
children to operate the sunroof
unintentionally, which could result in
serious injury if a child's hands, head
or neck becomes caught by the
sunroof.
Make sure the opening is clear before
closing the sunroof:
A closing sunroof is dangerous. The
hands, head, or even neck of a person,
especially a child, could be caught in it
as it closes, causing serious injury or
even death.
Make sure nothing blocks the sunroof
just before it reaches the fully closed
position:
Blocking the sunroof just before it
reaches the closed position is
dangerous.
In this case, the jam-safe function
cannot prevent the sunroof from
closing. If fingers are caught, serious
injuries could occur.
CAUTION
¾Do not sit on or put heavy items on
the area where the sunroof opens
and closes. Otherwise, the sunroof
could be damaged.
¾Do not open or close the sunroof
forcefully during freezing
temperatures or snowfall. Otherwise,
the sunroof could be damaged.
¾The sunshade does not tilt. To avoid
damaging the sunshade, do not push
it up.
¾Do not close the sunshade while the
sunroof is opening. Trying to force
the sunshade closed could damage
it.
▼Tilt/Slide Operation
The sunroof can be opened or closed
electrically only when the ignition is
switched ON.
xBefore leaving the vehicle or washing
your Mazda, make sure the sunroof
is completely closed so that water
does not get inside the cabin area.
xAfter washing your Mazda or after it
rains, wipe the water off the sunroof
before operating it to avoid water
Before Driving
Windows
3-44*Some models.

penetration which could cause rust
and water damage to your headliner.
1. Tilt/Slide switch
Tilt Operation
The rear of the sunroof can be tilted
open to provide more ventilation.

To fully tilt automatically, momentarily
press the tilt/slide switch.
To fully close automatically,
momentarily press the tilt/slide switch
in the forward direction.
To stop tilting partway, press the tilt/
slide switch.
When the sunroof is already slid open
and you want to tilt it open, first close
the sunroof and then do a tilt
operation.
1. Tilt up
2. Close (Tilt down)

Slide Operation
To fully open automatically,
momentarily press the tilt/slide switch
in the backward direction.
To fully close automatically,
momentarily press the tilt/slide switch
in the forward direction.
To stop sliding partway, press the tilt/
slide switch.
When the sunroof is already tilted
open and you want to slide it open,
first close the sunroof and then do a
slide operation.
1. Open
2. Close
NOTE
If the sunroof does not operate
normally, do the following procedure:
1. Switch the ignition ON.
2. Press the tilt switch, to partially tilt
open the rear of the sunroof.
3. Repeat Step 2. The rear of the
sunroof tilts open to the fully open
position, then closes a little.

If the reset procedure is performed
while the sunroof is in the slide
position (partially open) it will close
before the rear tilt opens.
▼Jam-safe Sunroof
If a person's hands, head or an object
blocks the sunroof while it is closing,
Before Driving
Windows
3-45

NOTE
xThe keys carry a unique electronic
code. For this reason, and to assure
your safety, obtaining a replacement
key requires some waiting time. They
are only available through an
Authorised Mazda Repairer.
xAlways keep a spare key in case one
is lost. If a key is lost, consult an
Authorised Mazda Repairer as soon
as possible.
xIf you lose a key, an Authorised
Mazda Repairer will reset the
electronic codes of your remaining
keys and immobilizer system. Bring
all the remaining keys to an
Authorised Mazda Repairer to reset.
Starting the vehicle with a key that
has not been reset is not possible.
▼Operation
NOTE
xThe engine may not start and security
indicator light may illuminate or flash
if the key is placed in an area where
it is difficult for the system to detect
the signal, such as on the instrument
panel or in the glove compartment.
Move the key to a location within
the signal range, switch the ignition
off, and then restart the engine.
xSignals from a TV or radio station, or
from a transceiver or mobile
telephone could interfere with your
immobilizer system. If you are using
the proper key and the engine fails to
start, check the security indicator
light.
Arming
The system is armed when the ignition
is switched from ON to off.
The security indicator light in the
instrument cluster flashes every 2
seconds until the system is disarmed.

Disarming
The system is disarmed when the
ignition is switched ON with the
correct programmed key. The security
indicator light illuminates for about 3
seconds and then turns
off.
If the engine does not start with the
correct key, and the security indicator
light remains illuminated or flashing ,
try the following:
Make sure the key is within the
operational range for signal
transmission. Switch the ignition
off,
and then restart the engine. If the
engine does not start after 3 or more
tries, contact an expert repairer (we
recommend an Authorised Mazda
Repairer).
Before Driving
Security System
3-48

Theft-Deterrent System*
▼Theft-Deterrent System
If the theft-deterrent system detects an
inappropriate entry into the vehicle or
the intrusion sensor detects movement
in the vehicle which could result in the
vehicle (with the intrusion sensor) or
its contents being stolen, the alarm
alerts the surrounding area of an
abnormality by sounding the siren/
horn and flashing the hazard warning
lights.

The system will not function unless it's
properly armed. So when you leave the
vehicle, follow the arming procedure
correctly.
Intrusion sensor
*
The intrusion sensor uses ultrasonic
waves to detect movement inside the
vehicle and to raise an alert of an
intrusion into the vehicle.

The intrusion sensor detects certain
kinds of movement inside the vehicle,
however, it may also respond to
phenomenon outside the vehicle such
as vibrations, loud noise, wind, and air
currents.
CAUTION
In order for the intrusion sensor to
operate appropriately, be aware of the
following:
¾Do not hang clothing or objects from
a head restraint or a coat hook.
¾Return the extension sunvisors to
their original positions.
¾Do not blind the intrusion sensor by
covering it or placing objects over it.
¾Do not allow the intrusion sensor to
get soiled or wipe it with a liquid.
¾Do not shock or cause an impact to
the intrusion sensor or the intrusion
sensor bezel.
¾Do not install seats that are not
Mazda genuine products.
¾To prevent obstruction of intrusion
sensor, do not place objects or cargo
near the intrusion sensor that are
higher than the head restraints.

1. Intrusion sensor and intrusion
sensor bezel
▼Operation
Siren/Horn triggering conditions
The siren/horn sounds intermittently
and the hazard warning lights flash for
about 30 seconds when the system is
triggered by any one of the following:
With the intrusion sensor
xUnlocking a door with the auxiliary
key, door lock switch, or an inside
door-lock knob.
xForcing open a door, the bonnet or
the liftgate.
xOpening the bonnet by operating
the bonnet release handle.
xSwitching the ignition ON without
using the push button start.
xThe intrusion sensor detects a
movement in the vehicle.
Before Driving
Security System
*Some models.3-49

The system will be triggered again (up
to 10 times) if one of the above
conditions remains.

xDisconnecting the battery terminal
(the hazard warning lights do not
flash).
The system will be triggered about 10
times.
Without the intrusion sensor
xUnlocking a door with the auxiliary
key, door lock switch, or an inside
door-lock knob.
xForcing open a door, the bonnet or
the liftgate.
xOpening the bonnet by operating
the bonnet release handle.
xSwitching the ignition ON without
using the push button start.
If the system is triggered again, the
lights and horn will activate until the
driver's door or the liftgate is unlocked
with the transmitter.
NOTE
xThe liftgate does not open while the
theft-deterrent system is operating.
xIf the battery goes dead while the
theft-deterrent system is armed, the
siren/horn will activate and the
hazard warning lights will flash when
the battery is charged or replaced.
▼How to Arm the System
1. Close the windows and the
sunroof* securely.
NOTE
(With the intrusion sensor)
Even with a window or the sunroof*
open, the system can be armed,
however, leaving the windows or
the sunroof
* even partially open can
invite theft, and wind blowing into
the vehicle could trigger the alarm.
The intrusion sensor function can
also be cancelled.
Refer to Cancelling the Intrusion
Sensor (With Intrusion Sensor) on
page 3-51.
2. Switch the ignition OFF.
3. Make sure the bonnet, the doors,
and the liftgate are closed.
4. Press the lock button on the
transmitter.
The hazard warning lights will flash
once.
The following method will also arm
the theft-deterrent system:
Press the door-lock switch “
”
while any door is open and then
close all of the doors.
(With the advanced keyless
function)
Touch the sensing area of the door
lock touch sensor.

The security indicator light in the
instrument cluster flashes twice per
second for 20 seconds.

5. After 20 seconds, the system is fully
armed.
Before Driving
Security System
3-50*Some models.

NOTE
xThe theft-deterrent system can
also be armed by activating the
auto relock function with all the
doors, the liftgate and the bonnet
closed.
Refer to Transmitter on page 3-5.
xThe system will disarm if one of
the following operations takes
place within 20 seconds after
pressing the lock button:
xUnlocking any door.xOpening any door.xOpening the bonnet.xSwitching the ignition ON.
To rearm the system, do the
arming procedure again.
xWhen the doors are locked by
pressing the lock button on the
transmitter while the
theft-deterrent system is armed,
the hazard warning lights will
flash once to indicate that the
system is armed.
▼Cancelling the Intrusion Sensor
(With the Intrusion Sensor)
If the theft deterrent system has been
armed while any of the following
conditions are present, cancel the
intrusion sensor to prevent the alarm
from triggering unnecessarily.
xLeaving the vehicle with a movable
object, passengers or pets remaining
inside.
xLeaving an object inside the vehicle
that can roll around, such as when
the vehicle is placed on a tilting,
unstable surface when being
shipped.
xHanging small objects/accessories in
the vehicle, hanging clothing on a
coat hook, or placing other items
which can move easily inside the
vehicle.
xParking in an area where there is
strong vibration or loud noise.
xWhen using a high pressure or
automatic car wash.
xContinuous shock and vibration from
hail or thunder and lightning is
transmitted to the vehicle.
xDoors are locked with a window or
the sunroof* left open.xAn accessory heater or device that
produces moving air and vibration
operates while the theft deterrent
system is armed.
NOTE
If any door or the liftgate remains
closed for 30 seconds, all the doors
and the liftgate automatically re-lock
and the theft deterrent system arms
even if a window and the sunroof
* is
left open.

To cancel the intrusion sensor, press
the intrusion sensor cancel button on
the transmitter within 20 seconds after
pressing the lock button.
The hazard warning lights will flash 3
times.
NOTE
xTo reactivate the intrusion sensor,
turn off the armed theft-deterrent
system and then rearm it.
xThe intrusion sensor is operational
when the theft-deterrent system is
armed. To cancel the intrusion
sensor, press the intrusion sensor
cancel button each time the
theft-deterrent system is armed.
▼To Turn Off an Armed System
An armed system can be turned off
using any one of the following
methods:
Before Driving
Security System
*Some models.3-51

Rocking the Vehicle
▼Rocking the Vehicle
WARNING
Do not spin the wheels at high speed,
and do not allow anyone to stand
behind a wheel when pushing the
vehicle:
When the vehicle is stuck, spinning the
wheels at high speed is dangerous. The
spinning tyre could overheat and
explode. This could cause serious
injuries.
CAUTION
Too much rocking may cause engine
overheating , transmission failure, and
tyre damage.
If you must rock the vehicle to free it
from snow, sand or mud, depress the
accelerator slightly and slowly move
the shift lever/selector lever from 1 (D)
to R position.
Winter Driving
▼Winter Driving
Carry emergency gear, including tyre
chains, window scraper,
flares, a small
shovel, jumper leads, and a small bag
of sand or salt.
Ask an expert repairer (we recommend
an Authorised Mazda Repairer) to
check the following:
xHave the proper ratio of antifreeze in
the radiator.
Refer to Engine Coolant on page
6-28.
xInspect the battery and its leads.
Cold reduces battery capacity.
xUse an engine oil appropriate for the
lowest ambient temperatures that
the vehicle will be driven in (page
6-24).
xInspect the ignition system for
damage and loose connections.
xUse washer fluid made with
antifreezeŠbut do not use engine
coolant antifreeze for washer fluid
(page 6-31).
NOTE
xRemove snow before driving. Snow
left on the windscreen is dangerous
as it could obstruct vision.
xDo not apply excessive force to a
window scraper when removing ice
or frozen snow on the mirror glass
and windscreen.
xNever use warm or hot water for
removing snow or ice from windows
and mirrors as it could result in the
glass cracking.
Before Driving
Driving Tips
3-56

4When Driving
Information concerning safe driving and stopping.
Start/Stop Engine..................... 4-4
Ignition Switch.......................4-4
Starting the Engine................. 4-5
Turning the Engine
Off.......... 4-10
i-stop
*................................. 4-11
Cylinder Deactivation
*..........4-20
Instrument Cluster and
Display.................................. 4-21
Instrument Cluster and
Display................................4-21
Instrument Cluster............... 4-21
Active Driving Display.......... 4-39
Manual Transmission
Operation.............................. 4-41
Manual Transmission Shift
Pattern................................ 4-41
Automatic Transmission........... 4-43
Automatic Transmission
Controls.............................. 4-43
Shift-Lock System................. 4-44
Transmission Ranges............ 4-45
Manual Shift Mode.............. 4-46
Direct Mode
*.......................4-52
Driving Tips......................... 4-53
Switches and Controls............. 4-54
Lighting Control................... 4-54
Rear Fog Light
*..................... 4-59
Turn and Lane-Change
Signals................................ 4-60
Windscreen Wipers and
Washer............................... 4-61
Rear Window Wiper and
Washer............................... 4-64
Headlight Washer
*............... 4-65
Rear Window Defogger........ 4-66
Horn................................... 4-67
Hazard Warning Flasher....... 4-68
Brake.....................................4-69
Brake System....................... 4-69
AUTOHOLD........................ 4-74
Emergency Stop Signal
System................................ 4-78
Hill Launch Assist (HLA)........4-79
ABS/TCS/DSC/Off-Road
Traction Assist.........................4-80
Antilock Brake System
(ABS).................................. 4-80
Traction Control System
(TCS).................................. 4-81
Dynamic Stability Control
(DSC)................................. 4-83
Off-Road Traction Assist
*...... 4-84
M Hybrid............................... 4-86
M Hybrid............................ 4-86
*Some models.4-1