2019 MAZDA MODEL CX-30 ignition

Locking
Unlocking
xThe system may not operate normally
under the following conditions.
xYou touch the sensing area of the
door lock touch sensor and the
sensing area of the door release
touch sensor at the same time.
xYou touch the sensing area of the
touch sensor while wearing gloves.
xForeign matter such as snow or dirt
is stuck on the sensing area of the
touch sensor.
xYou pull the door handle just after
touching the sensing area of the
touch sensor.
xThe system may operate if the outer
side door handle of a front door is
splashed with water by a car wash or
rain while the transmitter is in the
operation range.
xIf the system does not operate even
though you touch the sensing area of
the touch sensor correctly, release
the touch sensor once, and then
touch the sensing area of the touch
sensor again after waiting about 3
seconds.
Locking
When locking , touch the sensing area
of the door lock touch sensor with all
of the following conditions met.
xThe ignition is switched OFF.xAll the doors are closed.xYou are carrying the transmitter.
The following locations are locked by
touching the sensing area of the door
lock touch sensor.
xAll doorsxFuel-filler flapxLiftgate
When locking , the hazard warning
lights operate one time.
(Except European models)
A beep sound operate one time.
Unlocking
When unlocking , touch the sensing
area of the door release touch sensor
with all of the following conditions
met.
xThe ignition is switched OFF.xThe driver’s door is locked.xThree seconds or longer have passed
since the doors were locked.
xYou are carrying the transmitter.
Ty p e A
(Unlocking from the driver's door)
The following locations are unlocked
by touching the sensing area of the
door release touch sensor of the
driver's door.
Before Driving
Doors and Locks
3-14

A beep sound is heard when all
doors and the liftgate are closed
while the transmitter is being carried.
All the doors, fuel-filler flap, and
liftgate are locked automatically
when the transmitter is out of the
operational range. Also, the hazard
warning lights flash once. (Even if the
driver is in the operational range, all
the doors, fuel-filler flap, and liftgate
are locked automatically after about
30 seconds.) If you are out of the
operational range before the doors
and the liftgate are completely
closed or another transmitter is left
in the vehicle, the walk-away auto
lock function will not work. Always
make sure that all doors and the
liftgate are closed and locked before
leaving the vehicle. The walk-away
auto lock function does not close the
power windows.
x(Auto re-lock function)
After unlocking with the touch
sensor, all the doors , fuel-filler flap,
and liftgate will automatically lock if
any of the following operations are
not performed within about 30
seconds.
xOpening a door or the liftgate.xSwitching the ignition to any
position other than off.
If your vehicle has a theft-deterrent
system, the hazard warning lights will
flash for confirmation.
The time required for the doors to
lock automatically can be changed.
Refer to the Settings section in the
Mazda Connect Owner's Manual.
▼Locking, Unlocking with
Tra n s m i t te r
The following locations can be locked/
unlocked by operating the keyless
entry system transmitter. Refer to
Keyless Entry System (page 3-4).
xAll doorsxFuel-filler flapxLiftgate
▼Locking , Unlocking with
Door-Lock Switch
Door-lock switch on driver’s door
The following locations are locked/
unlocked by pressing the door-lock
switch.
xAll doorsxFuel-filler
flapxLiftgate
1. Unlock
2. Lock
Locking from the outside using the
door-lock switch
When locking from the outside using
the door-lock switch, press the lock
side of the door-lock switch with all of
the following conditions met and then
close all the doors.
xThe ignition is switched OFF.xAny door is open.
NOTE
xTo prevent the transmitter from being
left in the vehicle, make sure that you
carry the transmitter before locking.
Before Driving
Doors and Locks
3-16

xAfter locking by pressing the
door-lock switch and when all the
doors are closed with the transmitter
left in the vehicle, all the doors,
liftgate, and fuel-filler flap are
unlocked.
xAfter locking by pressing the
door-lock switch and when the
liftgate is closed last with the
transmitter left in the vehicle, only
the liftgate is unlocked.

Door-lock switch on liftgate (With the
advanced keyless function)
With power liftgate
All doors, fuel-filler flap, and the
liftgate can be locked by pressing the
door-lock switch.
In addition, the liftgate automatically
closes after locking.

Without power liftgate
All doors, fuel-filler flap, and the
liftgate can be locked by pressing the
door-lock switch.

With power liftgate
When locking using the door-lock
switch, press the door-lock switch with
all of the following conditions met. The
liftgate automatically closes after
locking.
xYou are carrying the transmitter.xThe ignition is switched OFF.xAll the doors are closed.xThe liftgate is not automatically
opening/closing.
xThe vehicle is stopped.
Before Driving
Doors and Locks
3-17

(With theft-deterrent system
(European models))
Before the liftgate closes, the hazard
warning lights operate 2 times and a
long beep sound is activated.
When the liftgate closes, the hazard
warning lights operate 1 time.

(With theft-deterrent system (Except
European models))
When locking, a beep sound operates
1 time.
In addition, before the liftgate closes,
the hazard warning lights operate 2
times and a long beep sound is
activated.
When the liftgate closes, the hazard
warning lights operate 1 time.

(Without theft-deterrent system
(European models))
When locking, the hazard warning
lights operate 1 time.
In addition, before the liftgate closes,
the hazard warning lights operate 2
times and a long beep sound is
activated.

(Without theft-deterrent system
(Except European models))
When locking, the hazard warning
lights and a beep sound operate 1
time.
In addition, before the liftgate closes,
the hazard warning lights operate 2
times and a long beep sound is
activated.

For details on the power liftgate
function, refer to Power Liftgate on
page 3-22.

Without power liftgate
When locking using the door-lock
switch, press the door-lock switch withall of the following conditions met and
then close the liftgate.
xYou are carrying the transmitter.xThe ignition is switched OFF.xAll the doors are closed.
(With theft-deterrent system
(European models))
When the liftgate closes, the hazard
warning lights operate 1 time.

(With theft-deterrent system (Except
European models))
When locking , a beep sound operates
1 time.
When the liftgate closes, the hazard
warning lights operate 1 time.

(Without theft-deterrent system
(European models))
When locking , the hazard warning
lights operate 1 time.

(Without theft-deterrent system
(Except European models))
When locking , the hazard warning
lights and a beep sound operate 1
time.
NOTE
xTo prevent the transmitter from being
left in the vehicle, make sure that you
carry the transmitter before locking.
xAfter locking by pressing the
door-lock switch and when the
liftgate is closed with the transmitter
left in the vehicle, the liftgate is
unlocked.
Before Driving
Doors and Locks
3-18

▼Auto Lock/Unlock Function
WARNING
Do not pull the inner handle on a
front door:
Pulling the inner handle on a front
door while the vehicle is moving is
dangerous. Passengers can fall out of
the vehicle if the door opens
accidentally , which could result in
death or serious injury.
xWhen the vehicle speed exceeds 20
km/h (12 mph), all the doors,
fuel-filler flap, and liftgate lock
automatically.
xWhen the ignition is switched off, all
the doors, fuel-filler flap, and liftgate
unlock automatically.
The auto lock/unlock function settings
can be changed.
Refer to the Settings section in the
Mazda Connect Owner's Manual.
▼Locking , Unlocking with
Door-Lock Knob
Operation from inside
To lock any door from the inside, press
the door-lock knob.
To unlock, pull it outward.
This does not operate the other door
locks.

1. Unlocked: Red indicator
2. Lock
3. Unlock

Operation from outside
To lock any door using its door-lock
knob from the outside, press the
door-lock knob to the lock position
and close the door (holding the door
handle in the open position is not
required).
This does not operate the other door
locks.

NOTE
When locking the door this way:
xBe careful not to leave the key inside
the vehicle.
xThe doors cannot be locked using
the driver's door lock knob if any
door or liftgate is open when the
ignition is switched to ACC or ON.
Before Driving
Doors and Locks
3-19

Operation using the transmitter
When the power liftgate button on the
transmitter is pressed and held for
about 1 second or longer with all of
the following conditions met, the
hazard warning lights flash 2 times, a
beep sound is activated, and the
liftgate automatically opens/closes
fully.
xThe ignition is switched OFF.xThe vehicle is stopped.
Refer to Transmitter on page 3-5.
NOTE
xWhen opening the liftgate by
pressing the power liftgate button on
the transmitter, the liftgate can be
opened even when it is locked.
xIf the power liftgate button on the
transmitter is pressed while the
liftgate is opening/closing
electrically, the beep is activated and
the liftgate stops. When pressing the
power liftgate button again, the
liftgate moves in the reverse
direction.
Operation using switch only for
power liftgate
Operation conditions
Opening the liftgate
If the vehicle has satisfied all the
following operation conditions, the
power liftgate can be opened using the
power function.
xAll doors and the liftgate are
unlocked.
xThe vehicle is stopped.x(Manual transmission)
The ignition is switched to a position
other than ON, or when the parking
brake is applied with the shift lever in
N and the ignition switched ON.
x(Automatic transmission)
The ignition is switched to a position
other than ON, or the selector lever
is in P with the ignition switched ON.
Closing the liftgate
xThe vehicle is stopped.x(Manual transmission)
The ignition is switched to a position
other than ON, or when the parking
brake is applied with the shift lever in
N and the ignition switched ON.
x(Automatic transmission)
The ignition is switched to a position
other than ON, or the selector lever
is in P with the ignition switched ON.
NOTE
If the shift lever/selector lever is shifted
to another position and the vehicle is
moved while the liftgate is opening/
closing automatically, the liftgate
operates as follows:
xWhen the liftgate is opening
A beep sound is activated, and the
liftgate moves in the reverse
direction automatically and closes.
xWhen the liftgate is closing
A beep sound is activated, but the
liftgate continues to close.
Operation from the driver's seat (To
open/close)
Press the power liftgate switch for
about 1 second or longer while the
liftgate is in the fully closed/open
position. The hazard warning lights
Before Driving
Doors and Locks
3-24

▼Emission Control System
(SKYACTIV-G 2.0, SKYACTIV-G
2.5, SKYACTIV-X 2.0)
This vehicle is equipped with an
emission control system (the catalytic
converter is part of this system) that
enables the vehicle to comply with
existing exhaust emissions
requirements.
WARNING
Never park over or near anything
flammable:
Parking over or near anything
flammable, such as dry grass, is
dangerous. Even with the engine
turned
off, the exhaust system remains
very hot after normal use and could
ignite anything
flammable. A resulting
fire could cause serious injury or death.
CAUTION
Ignoring the following precautions
could cause lead to accumulate on the
catalyst inside the converter or cause
the converter to get very hot. Either
condition will damage the converter
and cause poor performance.
¾USE ONLY UNLEADED FUEL.
¾Do not drive your Mazda with any
sign of engine malfunction.
¾Do not coast with the ignition
switched off.
¾Do not descend steep grades in gear
with the ignition switched off.
¾Do not operate the engine at high
idle for more than 2 minutes.
¾Do not tamper with the emission
control system. All inspections and
adjustments must be made by a
qualified technician.
¾Do not push-start or pull-start this
vehicle.
▼Emission Control System
(SKYACTIV-D 1.8)
This vehicle is equipped with an
emission control system (the catalytic
converter is part of this system) that
enables the vehicle to comply with
existing exhaust emissions
requirements.
WARNING
Never park over or near anything
flammable:
Parking over or near anything
flammable, such as dry grass, is
dangerous. Even with the engine
turned
off, the exhaust system remains
very hot after normal use and could
ignite anything
flammable. A resulting
fire could cause serious injury or death.
CAUTION
Ignoring the following precautions
could cause lead to accumulate on the
catalyst inside the converter or cause
the converter to get very hot. Either
condition will damage the converter
and cause poor performance.
¾Do not drive your Mazda with any
sign of engine malfunction.
¾Do not coast with the ignition
switched off.
¾Do not descend steep grades in gear
with the ignition switched off.
¾Do not operate the engine at high
idle for more than 2 minutes.
¾Do not tamper with the emission
control system. All inspections and
adjustments must be made by a
qualified technician.
¾Do not push-start or pull-start this
vehicle.
Before Driving
Fuel and Emission
3-32

Fuel-Filler Flap and Cap
▼Fuel-Filler Flap and Cap
WARNING
When removing the fuel-filler cap,
loosen the cap slightly and wait for
any hissing to stop, then remove it:
Fuel spray is dangerous. Fuel can burn
skin and eyes and cause illness if
ingested. Fuel spray is released when
there is pressure in the fuel tank and
the fuel-filler cap is removed too
quickly.
Before refuelling, stop the engine,
and always keep sparks and flames
away from the filler neck:
Fuel vapour is dangerous. It could be
ignited by sparks or flames causing
serious burns and injuries.
Additionally, use of the incorrect
fuel-filler cap or not using a fuel-filler
cap may result in a fuel leak, which
could result in serious burns or death
in an accident.
Do not continue refuelling after the
fuel pump nozzle shuts off
automatically:
Continuing to add fuel after the fuel
pump nozzle has shut off automatically
is dangerous because
overfilling the
fuel tank may cause fuel overflow or
leakage. Fuel overflow and leakage
could damage the vehicle and if the
fuel ignites it could cause a fire and
explosion resulting in serious injury or
death.
CAUTION
¾Always use only a designated Mazda
fuel-filler cap or an approved
equivalent, available at an expert
repairer (we recommend an
Authorised Mazda Repairer). The
wrong cap can result in a serious
malfunction of the fuel and emission
control systems.
¾When using an automatic car wash
or a high water pressure car washer,
lock the driver's door. Otherwise,
the
fuel-filler
flap may open
unexpectedly and could be
damaged.
▼Refuelling
Before refuelling, close all the doors,
windows, and liftgate, and switch the
ignition OFF.
1. Using the following , unlock the
driver’s door.
xTransmitter (page 3-16)xTouch sensor (page 3-13)xDoor-lock switch (page 3-16)xAuto lock/unlock function (page
3-19)
NOTE
xWhen the driver's door is locked/
unlocked, the fuel flap is also
locked/unlocked at the same
time.
xThe time until the fuel flap is
locked after locking the driver's
door can be changed.
Refer to the Settings section in
the Mazda Connect Owner's
Manual.
xHowever, if you change the time
until the fuel flap is locked,
locking of the fuel flap using the
following functions is not
applicable.
Before Driving
Fuel and Emission
3-34