2019 MAZDA MODEL CX-30 service

Refer to Table B to identify the required maintenance items.
Azerbaijan/Armenia
The vehicle status monitor feature alerts you of maintenance needs by turning on the
wrench indicator light or displaying a message in the instrument panel, or both.
Every maintenance must be done when the display/wrench indication comes on.
The display/wrench indication will come on before reaching the maximum interval.
Refer to Table B to identify the required maintenance items.

Maximum interval 5,000 km or 6 months, whichever comes
first

Manually set Next Service Distance of Vehicle Status Monitor to a shorter mileage
than 5,000 km if the vehicle is driven primarily under any of the following condi-
tions:
Refer to the Information section in the Mazda Connect Owner's Manual about the
manual setting procedure.
1. The vehicle is idled for long periods or driven at low speeds, such as with police
cars, taxis, or driver's education school car.
2. Driving under dusty conditions.
3. Driving for long periods in cold temperatures or driving regularly for short distan-
ces only.
4. Driving under extremely high temperature conditions.
5. Driving continuously in mountainous regions.
Refer to Table B to identify the required maintenance items.
Ta b l e A
Maintenance item 1st2nd3rd 4th 5th 6th 7th 8th 9th10th 11th 12th
Engine oil &
filter *1RRRRRRRRRRRR
Spark plug IIIIIIIRIIII
Drive belts
*2IIIIIIIIIIII
Engine coolant level IIIIIIIIIIII
Battery
*3*4IIIIIIIIIIII
Vacuum brake booster and
hoseWith vacuum
boosterIIIIII
Brake lines, hoses and connections I I I I I I I I I I I I
Disc brakes IIIIIIIIIIII
Steering operation and linkages I I I I I I I I I I I I
Bolts and nuts on chassis and body T T T T T T T T T T T T
Front and rear suspension, ball joints and
wheel bearing axial playIIIIIIIIIIII
Driveshaft dust boot IIIIIIIIIIII
Maintenance and Care
Scheduled Maintenance
6-9

Manually set Next Service Distance of Vehicle Status Monitor to a shorter mileage
than maximum interval (50 % of maximum mileage is recommended) if the vehicle
is driven primarily under any of the following conditions: Refer to the Information
section in the Mazda Connect Owner's Manual about the manual setting proce-
dure.
1. The vehicle is idled for long periods or driven at low speeds, such as with police
cars, taxis, or driver's education school car.
2. Driving under dusty conditions.
3. Driving for long periods in cold temperatures or driving regularly for short distan-
ces only.
4. Driving under extremely high temperature conditions.
5. Driving continuously in mountainous regions.
Maintenance item1st 2nd 3rd 4th 5th 6th 7th 8th 9th10t
h11t
h12t
h13t
h14t
h15t
h16t
h
SKYACTIV-G 2.0, SKYACTIV-G 2.5, AND SKYACTIV-X 2.0
Engine oil & filter
*1RRRRRRRRRRRRRRRR
Air filter
*2RR
Fuel filterExcept Tai-
wanReplace every 60,000 km (37,500 miles).
Taiwan Replace every 80,000 km (50,000 miles).
Spark plugs
*3
SKYACTIV-X
2.0Replace every 64,000 km (40,000 miles).
SKYAC-
TIV-G 2.0/
SKYAC-
TIV-G 2.5Replace every 120,000 km (75,000 miles).
SKYACTIV-D 1.8
Engine oil & filter
*1RRRRRRRRRRRRRRRR
Air
filter
*2CC R CC R CC
Fuel filter RRRR
SKYACTIV-G 2.0, SKYACTIV-G 2.5, SKYACTIV-X 2.0, AND SKYACTIV-D 1.8
Drive belts
*4IIIIIIIIIIIIIIII
Engine coolant level IIIIIIIIIIIIIIII
Brake & Clutch fluid level IIIIIIIIIIIIIIII
Disc brakes IIIIIIIIIIIIIIII
Bonnet striker IIIIIIIIIIIIIIII
Function of all lights IIIIIIIIIIIIIIII
Fuel lines and hoses IIIIIIII
Maintenance and Care
Scheduled Maintenance
6-12

Owner Maintenance
Precautions
▼Owner Maintenance Precautions
Routine Service
We highly recommend that these items
be inspected daily, or at least every
week.
xEngine Oil Level (page 6-27)xEngine Coolant Level (page 6-28)xBrake and clutch Fluid Level (page
6-30)
xWasher Fluid Level (page 6-31)xBattery Maintenance (page 6-37)xTy re
Inflation Pressure (page 6-41)

Improper or incomplete service may
result in problems. This section gives
instructions only for items that are easy
to perform.

As explained in the Introduction (page
6-2), several procedures can be done
only by a
qualified service technician
with special tools.

Improper do-it yourself maintenance
during the warranty period may affect
warranty coverage. For details, read the
separate Mazda Warranty statement
provided with the vehicle. If you are
unsure about any servicing or
maintenance procedure, have it done
by an expert repairer (we recommend
an Authorised Mazda Repairer).

There are strict environmental laws
regarding the disposal of waste oil and
fluids. Please dispose of your waste
properly and with due regard to the
environment.

We recommend that you entrust the oil
and fluid changes of your vehicle to an
expert repairer (we recommend an
Authorised Mazda Repairer).
WARNING
Do not perform maintenance work if
you lack sufficient knowledge and
experience or the proper tools and
equipment to do the work. Have
maintenance work done by a
qualified technician:
Performing maintenance work on a
vehicle is dangerous if not done
properly. You can be seriously injured
while performing some maintenance
procedures.
If you must run the engine while
working under the bonnet, make
certain that you remove all jewellery
(especially rings, bracelets, watches,
and necklaces) and all neckties,
scarves, and similar loose clothing
before getting near the engine or
cooling fan which may turn on
unexpectedly:
Working under the bonnet with the
engine running is dangerous. It
becomes even more dangerous when
you wear jewellery, loose clothing or
have long hair or a long beard.
Either can become entangled in
moving parts and result in injury.
Maintenance and Care
Owner Maintenance
6-16

NOTE
If the replacement is not done using
the correct procedure indicated in the
service manual, it could cause an
engine malfunction. Consult an expert
repairer (we recommend an
Authorised Mazda Repairer) for
details.
Inspect the antifreeze protection and
coolant level in the coolant reservoir at
least once a yearŠat the beginning of
the winter seasonŠand before
travelling where temperatures may
drop below freezing.

Inspect the condition and connections
of all cooling system and heater hoses.
Replace any that are swollen or
deteriorated.

The coolant should be at full in the
radiator and between the FULL and
LOW marks on the coolant reservoir
when the engine is cool.

If it is at or near LOW, add enough
coolant to the coolant reservoir to
provide freezing and corrosion
protection and to bring the level to
FULL.
Securely tighten the coolant reservoir
tank cap after adding coolant.
CAUTION
¾Radiator coolant will damage paint.
Rinse it off quickly if spilled.
¾If the “FL22” mark is shown on or
near the cooling system cap, use of
FL-22 is recommended when
replacing engine coolant. Using
engine coolant other than
FL-22 may
cause serious damage to the engine
and cooling system.

If the coolant reservoir is empty or new
coolant is required frequently, consult
an expert repairer (we recommend an
Authorised Mazda Repairer).
Maintenance and Care
Owner Maintenance
6-29

Wiper Blades
▼Wiper Blades
CAUTION
¾Hot waxes applied by automatic car
washers have been known to
affect
the wiper's ability to clean windows.
¾To prevent damage to the wiper
blades, do not use petrol,
paraffin,
paint thinner, or other solvents on or
near them.
¾When the wiper lever is in the AUTO
position and the ignition is switched
ON, the wipers may move
automatically in the following cases:
¾If the windscreen above the rain
sensor is touched.
¾If the windscreen above the rain
sensor is wiped with a cloth.
¾If the windscreen is struck with a
hand or other object.
¾If the rain sensor is struck with a
hand or other object from inside
the vehicle.
Be careful not to pinch hands or
fingers as it may cause injury, or
damage the wipers. When washing
or servicing the vehicle, make sure
the wiper lever is in the OFF
position.
¾Before lifting the windscreen wiper
blades
off the windscreen, always
follow the procedure for moving the
windscreen wiper blades. Otherwise,
a wiper blade, wiper arm, or the
bonnet could be damaged.
Refer to the Replacing Windscreen
Wiper Blades (page 6-32) section
for the procedure on how to move
the windscreen wiper blades to the
service position.
Contamination of either the
windscreen or the blades with foreign
matter can reduce wiper effectiveness.
Common sources are insects, tree sap,
and hot wax treatments used by some
commercial car washes.

If the blades are not wiping properly,
clean the window and blades with a
good cleaner or mild detergent; then
rinse thoroughly with clean water.
Repeat if necessary.
▼Replacing Windscreen Wiper
Blades
When the wipers no longer clean well,
the blades are probably worn or
cracked.
Replace them.
CAUTION
¾To prevent damaging a windscreen
wiper blade, wiper arm, or the
bonnet, perform the following
procedure.
¾Before lifting the windscreen wiper
blades off the windscreen, always
move them to the service position.
¾When putting the windscreen
wiper blades back on the
windscreen, make sure that they
are in the service position before
switching the ignition ON and
operating the windscreen wipers.
¾Replace with Mazda genuine wiper
blades. If they are replaced with
wiper blades other than a Mazda
genuine product, they may not wipe
with the same
efficiency as the
genuine product.
¾To prevent damage to the wiper
arms and other components, do not
try to sweep the wiper arm by hand.
Maintenance and Care
Owner Maintenance
6-32

¾Do not bend the blade rubber
unnecessarily when replacing it.
Otherwise, the metal stiffener in the
blade may deform and the
windscreen wiper operation may be
adversely affected.
¾Do not hold a wiper blade by its end
when raising the wiper arm.
Otherwise, the part may deform and
the wiping performance may lower.
NOTE
xYou can replace the wiper blades
yourself, however you cannot replace
the wiper arms.
If you want to replace the wiper
arms, consult an expert repairer (we
recommend an Authorised Mazda
Repairer).
xForcefully lowering the wiper arms
could damage the wiper arm and
blade, and may scratch or crack the
windscreen.
Replace the wiper blades using the
following procedure.
1. Move the wipers to the service
positions using the following
procedure.
a) Switch the ignition ON.
b) Switch the ignition OFF.
c) Press up the wiper switch to the
MIST position 2 times within 30
seconds after switching the
ignition OFF.
When the procedure is
completed, the wipers operate
and they stop at the service
positions.
2. Raise the wiper arms.
CAUTION
To prevent damage to the
windscreen let the wiper arm down
easily, do not let it slap down on
the windscreen.
3. Slide the blade component in the
direction of the arrow while
pressing the wiper arm tab to
remove the blade component from
the wiper arm.

4. Pull the blade rubber in the
direction of the arrow and slide it
to a position where the blade
holder groove can be checked.

5. Pull the end of the blade rubber
from the blade holder groove in the
direction of the arrow and remove
Maintenance and Care
Owner Maintenance
6-33

Always keep batteries out of
the reach of children:
Allowing children to play near batteries
is dangerous. Battery fluid could cause
serious injuries if it gets in the eyes or
on the skin.
Keep flames and sparks away
from open battery cells and do not
allow metal tools to contact the
positive (+) or negative (-) terminal of
the battery when working near a
battery. Do not allow the positive (+)
terminal to contact the vehicle body:
Flames and sparks near open battery
cells are dangerous. Hydrogen gas,
produced during normal battery
operation, could ignite and cause the
battery to explode. An exploding
battery can cause serious burns and
injuries. Keep all flames including
cigarettes and sparks away from open
battery cells.
Keep all flames and sparks
away from open battery cells because
hydrogen gas is produced from open
battery cells while charging the
battery or adding battery
fluid:
Flames and sparks near open battery
cells are dangerous. Hydrogen gas,
produced during normal battery
operation, could ignite and cause the
battery to explode. An exploding
battery can cause serious burns and
injuries. Keep all
flames including
cigarettes and sparks away from open
battery cells.
NOTE
Before performing battery
maintenance, remove the battery
cover.

▼Battery Maintenance
To get the best service from a battery:
xKeep it securely mounted.xKeep the top clean and dry.xKeep terminals and connections
clean, tight, and coated with
petroleum jelly or terminal grease.
xRinse off spilled electrolyte
immediately with a solution of water
and baking soda.
xIf the vehicle will not be used for an
extended time, disconnect the
battery leads and charge the battery
every 6 weeks.
Maintenance and Care
Owner Maintenance
6-37

evaporates, the minerals will
concentrate and harden to form white
rings. The rings can damage your
vehicle's finish.
Prevention
It is necessary to wash and wax your
vehicle to preserve its
finish according
to the instructions in this section.
These steps should be taken
immediately after you find water marks
on your vehicle's finish.
Paint Chipping
Occurrence
Paint chipping occurs when gravel
thrown in the air by another vehicle's
tyres hits your vehicle.
How to avoid paint chipping
Keeping a safe distance between you
and the vehicle ahead reduces the
chances of having your paint chipped
by
flying gravel.
NOTE
xThe paint chipping zone varies with
the speed of the vehicle. For
example, when travelling at 90 km/h
(56 mph), the paint chipping zone is
50 m (164 ft).
xIn low temperatures a vehicle's
finish
hardens. This increases the chance of
paint chipping.
xChipped paint can lead to rust
forming on your Mazda. Before this
happens, repair the damage by using
Mazda touch-up paint according to
the instructions in this section.
Failure to repair the affected area
could lead to serious rusting and
expensive repairs.

Follow all label and container
directions when using a chemical
cleaner or polish. Read all warnings
and cautions.
▼Maintaining the Finish
Washing
CAUTION
¾Before lifting the windscreen wiper
blades off the windscreen, always
follow the procedure for moving the
windscreen wiper blades. Otherwise,
a wiper blade, wiper arm, or the
bonnet could be damaged.
Refer to the Replacing Windscreen
Wiper Blades (page 6-32) section for
the procedure on how to move the
windscreen wiper blades to the
service position.
¾When the wiper lever is in the AUTO
position and the ignition is switched
ON, the wipers may move
automatically in the following cases:
¾If the windscreen above the rain
sensor is touched or wiped with a
cloth.
¾If the windscreen is struck with a
hand or other object from either
outside or inside the vehicle.
Keep hands and scrapers clear of the
windscreen when the wiper lever is
in the AUTO position and the
ignition is switched ON as
fingers
could be pinched or the wipers and
wiper blades damaged when the
wipers activate automatically.
If you are going to clean the
windscreen, be sure the wipers are
turned off completely (when it is
most likely that the engine is left
running) this is particularly important
when clearing ice and snow.
Maintenance and Care
Appearance Care
6-55