2019 MAZDA MODEL CX-30 fog light

¾The vehicle is driven on roads with
lane lines other than white (yellow)
lines, such as an expressway.

Do not get out of the vehicle while
the stop hold control is operating.
(Automatic transmission vehicle)
Getting out of the vehicle while the
stop hold control is operating is
dangerous as the vehicle may move
unexpectedly and result in an accident.
Before getting out of the vehicle,
switch the CTS off, apply the parking
brake, and then shift the selector lever
to the P position.

CAUTION
Turn the system off when the vehicle is
running on a chassis roller.
Heed the following cautions so that
the CTS can operate normally.
¾Turn the system off when the vehicle
is running on a chassis roller.
¾Do not modify the vehicle's
suspensions.
¾Always use wheels of the specified
size for the front and rear wheels.
Consult an expert repairer (we
recommend an Authorised Mazda
Repairer) for tyre replacement.

NOTE
xThe headway control does not detect
the following as physical objects.
xVehicles approaching in the
opposite direction
xPedestriansxStationary objects (stopped
vehicles, obstructions)
xIf a vehicle ahead is travelling at an
extremely low speed, the system may
not detect it correctly.
xIf there is a structure on the road or
an object (such as a monorail) at a
low height off the ground in front of
the vehicle, the system may operate.
Therefore, do not use the CTS.
xDo not use the CTS under conditions
in which close proximity warnings
are frequently activated.
xIf it is necessary to accelerate for a
lane change or the vehicle ahead
brakes suddenly causing you to close
in on the vehicle rapidly, accelerate
using the accelerator pedal or
decelerate using the brake pedal
depending on the conditions.
xWhile the CTS is in use, any intended
engine braking does not occur even
if you shift the shift lever (manual
transmission) or the selector lever
(automatic transmission). If
deceleration is required, lower the
vehicle speed setting or depress the
brake pedal.
xWhile braking by the CTS control is
operating , you might hear an
operation sound, however, this does
not indicate a problem.
xThe brake lights turn on while
braking by the CTS control is
operating, however, they may not
turn on while the vehicle is on a
down slope at the set vehicle speed
or travelling at a constant speed and
following a vehicle ahead.
xUnder the following conditions, the
CTS may not be able to detect white
(yellow) lines or vehicles ahead
correctly and the CTS may not
operate normally.
xThe forward sensing camera (FSC)
cannot recognise the area in front
of the vehicle due to soiling or fog.
When Driving
i-ACTIVSENSE
4-150

xThe white (yellow) lane lines are
less visible because of dirt or paint
flaking.
xWhite (yellow) lane lines or
vehicles ahead are less visible
because of bad weather (rain, fog,
or snow).
xThe vehicle is driven on a
temporary lane or section with a
closed lane resulting from
construction where there might be
multiple white (yellow) lane lines,
or they are interrupted.
xThe camera picks up an obscure
line, such as a temporary line being
used for construction, or because
of shade, unmelted snow, or
grooves filled with water.
xThe road surface is wet and shiny
after rain, or there are puddles on
the road.
xHeavy luggage is loaded in the
luggage compartment or on the
rear seat causing the vehicle to tilt.
xA vehicle in front of your vehicle is
running near a white (yellow) lane
line making it less visible.
xThe windscreen is dirty or foggy.xThe vehicle is driven through an
intersection, a junction, or a fork in
the road.
xWhile white (yellow) lane lines
cannot be detected due to road or
weather conditions.
xThe surrounding brightness
suddenly changes such as when
entering or exiting a tunnel.
xThe illumination of the headlights
is weakened because of dirt or the
optical axis is deviated at night.
xBack-light is reflected off the road
surface or the road surface is wet
and shiny after rain.
xThe shade of a guardrail parallel to
a white (yellow) lane line is cast on
the road.
xThe width of a lane is excessively
narrow or wide.
xThe road is excessively uneven.xThe vehicle is shaken after hitting a
road bump.
xThere are various road markings or
division lines (lane markings) of
various shapes near an
intersection.
xThe area in front of the camera is
soiled or an object that obstructs
the field of view is installed.
xExhaust gas from the vehicle in
front, sand, snow, and water
vapour rising from manholes and
grating, and water splashed into
the air.
xThe surroundings are dark such as
during the early evening or early
morning.
xA vehicle ahead with a certain tail
light shape.
xA vehicle ahead veers off course
from your vehicle's line of travel.
xA vehicle ahead is driving
erratically.
xThe vehicle is driven on roads with
tight curves.

Headway control function
If a vehicle ahead is detected while
travelling at a constant speed, the
vehicle-ahead indication is displayed
and headway control is performed.

Steering assist function
When lane lines are detected, the
function assists the driver in keeping
the vehicle within the lane lines. If lane
lines are not detected, the function
provides the driver driving assistance in
keeping the vehicle along the motion
path with the vehicle ahead.
When Driving
i-ACTIVSENSE
4-151

¾The functions of the LAS have
limitations. Always stay on course
using the steering wheel and drive
with care.
¾Do not use the LAS under the
following circumstances, otherwise it
may result in an accident.
¾The vehicle is driven on slippery
roads such as icy or snow-covered
roads, and unpaved roads.
¾Tyres of a
different
specified size
are used, such as a temporary
spare tyre.
¾Tyres with
insufficient tread are
used.
¾The tyre pressures are not adjusted
to the
specified pressure.
¾The vehicle is being used to tow a
camper or boat trailer.
¾Tyre chains are used.
¾The vehicle is driven on roads with
lane lines other than white (yellow)
lines, such as an expressway.
CAUTION
Heed the following cautions so that
the LAS can operate normally.
¾Do not modify the vehicle's
suspensions.
¾Always use tyres of the specified type
and size for the front and rear
wheels. Consult an expert repairer
(we recommend an Authorised
Mazda Repairer) for tyre
replacement.
NOTE
The system may not operate normally
under the following conditions.
xThe white (yellow) lane lines are less
visible because of dirt or paint
flaking.
xWhite (yellow) lane lines are less
visible because of bad weather (rain,
fog, or snow).
xThe vehicle is driven on a temporary
lane or section with a closed lane
resulting from construction where
there might be multiple white
(yellow) lane lines, or they are
interrupted.
xThe camera picks up an obscure line,
such as a temporary line being used
for construction, or because of
shade, unmelted snow, or grooves
filled with water.
xThe surrounding brightness suddenly
changes such as when entering or
exiting a tunnel.
xBack-light is reflected off the road
surface.
xThe road surface is wet and shiny
after rain, or there are puddles on
the road.
xThe width of a lane is excessively
narrow.
xThe vehicle is driven on roads with
tight curves.
xHeavy luggage is loaded in the
luggage compartment or on the rear
seat causing the vehicle to tilt.
xThe vehicle is driven through a fork in
the road or a junction.
xThe shade of a guardrail parallel to a
white (yellow) lane line is cast on the
road.
xThe illumination of the headlights is
weakened because of dirt or the
optical axis is deviated at night.
xThe road is excessively uneven.xThe vehicle is shaken after hitting a
road bump.
xA vehicle in front of your vehicle is
running near a white (yellow) lane
line making it less visible.
xThe windscreen is dirty or foggy.
When Driving
i-ACTIVSENSE
4-163

xStrong light is directed from the front
of the vehicle (such as sunlight, or
headlights (high-beam) of
on-coming vehicles).
▼System Operation
When the ignition is switched ON, the
i-ACTIVSENSE status symbol (warning/
risk avoidance support system) (white)
turns on and the system goes on
standby.
NOTE
If the i-ACTIVSENSE status symbol
(warning/risk avoidance support
system) (white) does not turn on, the
system is cancelled using the
i-ACTIVSENSE switch or the
personalisation feature.
Operation conditions
When all of the following conditions
are met, the i-ACTIVSENSE status
symbol (warning/risk avoidance
support system) on the
multi-information display changes
from white to green and the system
becomes operational.
xThe vehicle speed is about 60 km/h
(37 mph) or faster.
xThe system detects white (yellow)
lane lines.
NOTE
When the system does not detect a
white (yellow) lane line on one side
only, the system does not operate on
the side that is not being detected.
When temporarily cancelling the
system
The LAS goes on standby in the
following cases: The LAS operation is
automatically restored when the
system's operation conditions are met.
xThe system cannot detect white
(yellow) lane lines.
xThe vehicle speed is less than about
55 km/h (34 mph).
xThe direction indicator lever is
operated.
xThe accelerator pedal is depressed
abruptly.
xThe TCS/DSC is operating.xThe TCS is turned
off.xThe steering wheel is operated.xThe brake pedal is operated.
The function is temporarily stopped.
The LAS stops functioning in the
following cases:
xThe temperature in the forward
sensing camera (FSC) is too high or
too low.
xThe windscreen around the forward
sensing camera (FSC) is foggy.
xThe windscreen around the forward
sensing camera (FSC) is blocked by
an obstruction, causing poor forward
visibility.
xStrong light (such as sunlight, or
headlights (high-beam) of
on-coming vehicles) is directed at
the forward sensing camera (FSC).
System malfunction
If there is a problem with the system,
the i-ACTIVSENSE status symbol
When Driving
i-ACTIVSENSE
4-164

xThe SBS-R system will operate under
the following conditions.
xThe engine is running.xThe shift lever (manual
transmission vehicle) or the
selector lever (automatic
transmission vehicle) is in the R
(reverse) position.
xi-ACTIVSENSE warning indication/
warning light is not displayed in the
multi-information display.
xThe vehicle speed is between
about 2 to 8 km/h (2 to 4 mph).
xThe SBS-R is not turned off.xThe DSC is not malfunctioning.xIn the following cases, the rear
ultrasonic sensor and rear camera
cannot detect obstructions and the
SBS-R may not operate.
xThe height of the obstruction is
low such as low walls or trucks
with low loading platforms.
xThe height of the obstruction is
high such as trucks with high
loading platforms.
xThe obstruction is small.xThe obstruction is thin such as a
signpost.
xThe surface of the obstruction is
not pointed vertically relative to
the vehicle.
xThe obstruction is soft such as a
hanging curtain or snow stuck to a
vehicle.
xThe obstruction is shaped
irregularly.
xThe obstruction is extremely close.xIn the following cases, the rear
ultrasonic sensor and rear camera
cannot detect obstructions correctly
and the
SBS-R may not operate.
xSomething is stuck on the bumper
near a rear ultrasonic sensor.
xThe brake or accelerator pedal is
operated.
xThere is another obstruction near
one obstruction.
xDuring inclement weather such as
rain, fog and snow.
xHigh or low humidity.xHigh or low temperaturesxStrong winds.xThe path of travel is not flat.xHeavy luggage is loaded in the
luggage compartment or on the
rear seat.
xObjects such as a wireless aerial,
fog light, or illuminated number
plate is installed near a rear
ultrasonic sensor.
xThe orientation of a rear ultrasonic
sensor has deviated for reasons
such as a collision.
xThe vehicle is affected by other
sound waves such as the horn,
engine noise, ultrasonic sensor of
another vehicle.
xIn the following cases, a rear
ultrasonic sensor and rear camera
may detect something as a target
obstruction which could cause the
SBS-R system to operate.
xDriving on a steep slope.xWheel blocks.xHanging curtains, gate poles such
as at toll gates and railroad
crossing.
xWhen travelling near objects such
as foliage, barriers, vehicles, walls,
and fences along a road.
xWhen driving off-road in areas
where there is grass and forage.
xWhen passing through low gates,
narrow gates, car washing
machines, and tunnels.
xA trailer is connected.xA bright light source such as
sunlight hits the rear camera.
xThe surroundings are dark.
When Driving
i-ACTIVSENSE
4-179

¾Always keep the windscreen glass
around the camera clean by
removing dirt or fogging. Use the
windscreen defroster to remove
fogging on the windscreen.
¾Consult an expert repairer (we
recommend an Authorised Mazda
Repairer) regarding cleaning the
interior side of the windscreen
around the Forward Sensing
Camera (FSC).
¾Consult an expert repairer (we
recommend an Authorised Mazda
Repairer) before performing
repairs around the Forward Sensing
Camera (FSC).
¾The Forward Sensing Camera (FSC)
is installed to the windscreen.
Consult an expert repairer (we
recommend an Authorised Mazda
Repairer) for windscreen repair
and replacement.
¾When cleaning the windscreen, do
not allow glass cleaners or similar
cleaning fluids to get on the
Forward Sensing Camera (FSC)
lens. In addition, do not touch the
Forward Sensing Camera (FSC)
lens.
¾When performing repairs around
the rearview mirror, consult an
expert repairer (we recommend an
Authorised Mazda Repairer).
¾Consult an expert repairer (we
recommend an Authorised Mazda
Repairer) regarding cleaning of the
camera lens.¾Do not hit or apply strong force to
the Forward Sensing Camera (FSC)
or the area around it. If the
Forward Sensing Camera (FSC) is
severely hit or if there are cracks or
damage caused by flying gravel or
debris in the area around it, stop
using the following systems and
consult an expert repairer (we
recommend an Authorised Mazda
Repairer).
¾High Beam Control System
(HBC)
¾Adaptive LED Headlights (ALH)
¾Lane Departure Warning System
(LDWS)
¾Traffic Sign Recognition System
(TSR)
¾Distance & Speed Alert (DSA)
¾Driver Attention Alert (DAA)
¾Mazda Radar Cruise Control
(MRCC)
¾Mazda Radar Cruise Control
with Stop & Go function (MRCC
with Stop & Go function)
¾Lane-keep Assist System (LAS)
¾Cruising & Traffic Support (CTS)
¾Smart Brake Support (SBS)
¾The direction in which the Forward
Sensing Camera (FSC) is pointed
has been finely adjusted. Do not
change the installation position of
the Forward Sensing Camera (FSC)
or remove it. Otherwise, it could
result in damage or malfunction.
¾Always use tyres for all wheels that
are of the specified size, and the
same manufacturer, brand, and tread
pattern. In addition, do not use tyres
with significantly different wear
patterns on the same vehicle as the
system may not operate normally.
When Driving
i-ACTIVSENSE
4-217

¾The Forward Sensing Camera (FSC)
includes a function for detecting a
soiled windscreen and informing the
driver, however, depending on the
conditions, it may not detect plastic
shopping bags, ice or snow on the
windscreen. In such cases, the
system cannot accurately determine
a vehicle ahead and may not be able
to operate normally. Always drive
carefully and pay attention to the
road ahead.
NOTE
xIn the following cases, the Forward
Sensing Camera (FSC) cannot detect
target objects correctly, and each
system may be unable to operate
normally.
xThe height of the vehicle ahead is
low.
xYou drive your vehicle at the same
speed as the vehicle ahead.
xHeadlights are not turned on
during the night or when going
through a tunnel.
xIn the following cases, the Forward
Sensing Camera (FSC) may not be
able to detect target objects
correctly.
xUnder bad weather condition,
such as rain, fog and snow.
xThe window washer is being used
or the windscreen wipers are not
used when it's raining.
xIce, fog, snow, frost, rainfall, dirt,
or foreign matter such as a plastic
bag is stuck on the windscreen.
xTrucks with low loading platforms
and vehicles with an extremely low
or high profile.
xWhen driving next to walls with no
patterning (including fences and
longitudinally striped walls).
xThe tail lights of the vehicle ahead
are turned off.
xA vehicle is outside the
illumination range of the
headlights.
xThe vehicle is making a sharp turn,
or ascending or descending a steep
slope.
xEntering or exiting a tunnel.xHeavy luggage is loaded causing
the vehicle to tilt.
xStrong light is shone at the front of
the vehicle (back light or
high-beam light from on-coming
vehicles).
xThere are many light emitters on
the vehicle ahead.
xWhen the vehicle ahead is not
equipped with tail lights or the tail
lights are turned off at nighttime.
xElongated luggage or cargo is
loaded onto installed roof rails and
covers the Forward Sensing
Camera (FSC).
xExhaust gas from the vehicle in
front, sand, snow, and water
vapour rising from manholes and
grating , and water splashed into
the air.
xWhen towing a malfunctioning
vehicle.
xThe vehicle is driven with tyres
having significantly different wear.
xThe vehicle is driven on down
slopes or bumpy roads.
xThere are water puddles on the
road.
xThe surroundings are dark such as
during the night, early evening, or
early morning , or in a tunnel or
indoor parking lot.
xThe illumination brightness of the
headlights is reduced or the
headlight illumination is weakened
due to dirt or a deviated optical
axis.
When Driving
i-ACTIVSENSE
4-218

xThe target object enters the blind
spot of the Forward Sensing
Camera (FSC).
xA person or object bursts onto the
road from the shoulder or cuts
right in front of you.
xYou change lanes and approach a
vehicle ahead.
xWhen driving extremely close to
the target object.
xTyre chains or a temporary spare
tyre is installed.
xThe vehicle ahead has a special
shape. For example, a vehicle
towing a trailer house or a boat, or
a vehicle carrier carrying a vehicle
with its front pointed rearward.
xIf the Forward Sensing Camera (FSC)
cannot operate normally due to rain,
backlight, or fog , the system
functions related to the Forward
Sensing Camera (FSC) are
temporarily stopped and the
following warning lights turn on.
However, this does not indicate a
malfunction.
xHigh Beam Control System (HBC)
warning indication/warning light
(amber)
xAdaptive LED Headlights (ALH)
warning indication/warning light
(amber)
xi-ACTIVSENSE warning indication/
warning light
xIf the Forward Sensing Camera (FSC)
cannot operate normally due to high
temperatures, the system functions
related to the Forward Sensing
Camera (FSC) are temporarily
stopped and the following warning
lights turn on. However, this does
not indicate a malfunction. Cool
down the area around the Forward
Sensing Camera (FSC) such as by
turning on the air conditioner.
xHigh Beam Control System (HBC)
warning indication/warning light
(amber)
xAdaptive LED Headlights (ALH)
warning indication/warning light
(amber)
xi-ACTIVSENSE warning indication/
warning light
xIf the Forward Sensing Camera (FSC)
detects that the windscreen is dirty
or foggy, the system functions related
to the Forward Sensing Camera
(FSC) are temporarily stopped and
the following warning lights turn on.
However, this does not indicate a
problem. Remove the dirt from the
windscreen or press the defroster
switch and defog the windscreen.
xHigh Beam Control System (HBC)
warning indication/warning light
(amber)
xAdaptive LED Headlights (ALH)
warning indication/warning light
(amber)
xi-ACTIVSENSE warning indication/
warning light
xIf there are recognizable cracks or
damage caused by
flying gravel or
debris on the windscreen, always
have the windscreen replaced.
Consult an expert repairer (we
recommend an Authorised Mazda
Repairer) for replacement.
xThe Forward Sensing Camera (FSC)
recognises pedestrians when all of
the following conditions are met:
xThe height of a pedestrian is about
1 to 2 meters.
xAn outline such as the head, both
shoulders, or the legs can be
determined.
xIn the following cases, the Forward
Sensing Camera (FSC) may not be
able to detect target objects
correctly:
When Driving
i-ACTIVSENSE
4-219