2019 MAZDA MODEL CX-30 fog light

xThe road surface is wet and shiny
after rain, or there are puddles on
the road.
xThe width of a lane is excessively
narrow.
xThe vehicle is driven on roads with
tight curves.
xHeavy luggage is loaded in the
luggage compartment or on the rear
seat causing the vehicle to tilt.
xThe vehicle is driven through a fork in
the road or a junction.
xThe shade of a guardrail parallel to a
white (yellow) lane line is cast on the
road.
xThe illumination of the headlights is
weakened because of dirt or the
optical axis is deviated at night.
xThe road is excessively uneven.xThe vehicle is shaken after hitting a
road bump.
xA vehicle in front of your vehicle is
running near a white (yellow) lane
line making it less visible.
xThe windscreen is dirty or foggy.xStrong light is directed from the front
of the vehicle (such as sunlight, or
headlights (high-beam) of
on-coming vehicles).
xThe vehicle is driven through an
intersection or a roundabout.
▼When the System Operates
When the ignition is switched ON, the
i-ACTIVSENSE status symbol (warning/
risk avoidance support system) (white)
turns on and the system goes on
standby.
NOTE
If the i-ACTIVSENSE status symbol
(warning/risk avoidance support
system) (white) does not turn on, the
system is cancelled using the
i-ACTIVSENSE switch or the
personalisation feature.
Operation conditions
When all of the following conditions
are met, the i-ACTIVSENSE status
symbol (warning/risk avoidance
support system) on the
multi-information display changes
from white to green and the system
becomes operational.
xThe ignition is switched ON.xThe vehicle speed is about 60 km/h
(37 mph) or faster.
xThe system detects white (yellow)
lane lines.
NOTE
When the system does not detect a
white (yellow) lane line on one side
only, the system does not operate on
the side that is not being detected.
When temporarily cancelling the
system
The LDWS goes on standby in the
following cases: The LDWS operation
is automatically restored when the
system's operation conditions are met.
xThe system cannot detect white
(yellow) lane lines.
xThe vehicle speed is less than about
55 km/h (34 mph).
xThe direction indicator lever is
operated.
xThe accelerator pedal is depressed.
When Driving
i-ACTIVSENSE
4-104

xThe steering wheel is operated.xThe brake pedal is operated.
The function is temporarily stopped.
The LDWS stops functioning in the
following cases:
xThe temperature in the forward
sensing camera (FSC) is too high or
too low.
xThe windscreen around the forward
sensing camera (FSC) is foggy.
xThe windscreen around the forward
sensing camera (FSC) is blocked by
an obstruction, causing poor forward
visibility.
xStrong light (such as sunlight, or
headlights (high-beam) of
on-coming vehicles) is directed at
the forward sensing camera (FSC).
System malfunction
If there is a problem with the system,
the i-ACTIVSENSE status symbol
(warning/risk avoidance support
system) (white) and the i-ACTIVSENSE
warning indication/warning light on
the multi-information display turns on
and a message is indicated.
Refer to i-ACTIVSENSE Status Symbol
(Warning/Risk Avoidance Support
System) on page 4-96.
▼Lane Departure Warning
If the system determines that the
vehicle may deviate from its lane, a
warning (beep sound, steering wheel
vibration) is activated and the direction
in which the system determines that
the vehicle may deviate is indicated on
the multi-information display and the
active driving display.
Multi-information display
Active driving display
NOTE
xThe LDWS settings can be changed.
Refer to the Settings section in the
Mazda Connect Owner's Manual.
xYou may not be able to hear the
LDWS warning sound depending on
the surrounding conditions such as
outside noise.
xIf you set the LDWS to vibrate the
steering wheel, you may not feel the
vibrations depending on the road
surface conditions.
▼Cancelling the System
The LDWS can be set to inoperable.
x(If only the LDWS is turned off)
Refer to the Settings section in the
Mazda Connect Owner's Manual.
x(If the LDWS is turned off by
operating the i-ACTIVSENSE switch)
Refer to i-ACTIVSENSE Switch on
page 4-97.
When Driving
i-ACTIVSENSE
4-105

1. The walls at the entrance and
exits of tunnels, turnouts.

xA BSM warning indicator light may
flash or the warning beep may be
activated several times when making
a turn at a city intersection.
xTurn off the BSM while pulling a
trailer or while an accessory such as a
bicycle carrier is installed to the rear
of the vehicle. Otherwise, the radar’s
radio waves will be blocked causing
the system to not operate normally.
xIf a Mazda genuine trailer hitch is
used, the BSM is automatically
turned off.
xIn the following cases, it may be
difficult to view the illumination/
flashing of the BSM warning
indicator lights equipped on the
door mirrors.
xSnow or ice is adhering to the door
mirrors.
xThe front door glass is fogged or
covered in snow, frost or dirt.
xThe rear side radar sensor of the BSM
may be regulated under the radio
wave related laws of the country
where the vehicle is driven. If this
system is used abroad, it may be
necessary to turn off the system.
Refer to Rear Side Radar Sensor on
page 4-224.
xThe system switches to the Rear
Cross
Tra ffi c Alert (RCTA) function
when the shift lever (manual
transmission) or the selector lever
(automatic transmission) is shifted to
the reverse (R) position.
Refer to Rear Cross
Tra ffi c Alert
(RCTA) on page 4-126.
▼Blind Spot Monitoring (BSM)
Warning Indicator Lights/Display
Indicator/Blind Spot Monitoring
(BSM) Warning Beep
The BSM system notifies the driver of
the presence of vehicles in adjacent
lanes or at the rear of the vehicle using
the BSM warning indicator light, the
warning sound and the display
indicator while the systems are
operational.
BSM warning indicator lights
The BSM warning indicator lights are
equipped on the left and right door
mirrors. The warning indicator lights
turn on when a vehicle approaching
from the rear in an adjacent lane is
detected.
When the ignition is switched ON, the
warning indicator light turns on
momentarily and then turns off after a
few seconds.
Function for cancelling illumination
dimmer
If the BSM warning indicator lights turn
on when the position lights are turned
on, the brightness of the BSM warning
indicator lights is dimmed.
If the BSM warning indicator lights are
difficult to see due to glare from
surrounding brightness when travelling
on snow-covered roads or under foggy
conditions, press the dimmer
cancellation button to cancel the
dimmer and increase the brightness of
When Driving
i-ACTIVSENSE
4-109

xThe TSR does not operate if there is a malfunction in the Forward Sensing Camera
(FSC).
xUnder the following conditions, the TSR may not operate normally.
xAn object placed on the instrument panel is reflected in the windscreen and
picked up by the camera.
xHeavy luggage is loaded in the luggage compartment or on the rear seat and the
vehicle is tilted.
xThe tyre pressures are not adjusted to the specified pressure.xTyres other than standard tyres are equipped.xThe vehicle is driven on the ramp and surrounding area to or from a rest area or
a tollgate on a highway.
xWhen surrounding brightness suddenly changes such as when entering or exiting
a tunnel.
xThe illumination of the headlights is weakened because of dirt or the optical axis
is deviated.
xThe windscreen is dirty or foggy.xThe windscreen and camera are fogged (water droplets).xStrong light is directed at the front of the vehicle (such as backlight or high-beam
headlights of on-coming vehicles).
xThe vehicle is making a sharp turn.xStrong light reflects off the road.xA traffic sign is in a position which makes it difficult to reflect the light from the
vehicle's headlights, such as when the vehicle is driven at night or in a tunnel.
xThe vehicle is driven under weather conditions such as rain, fog, or snow.xThe stored map data for the navigation system is not current.xA traffic sign is obscured by mud or snow.xA traffic sign is concealed by trees or a vehicle.xA
traffic sign is partially shaded.xA traffic sign is bent or warped.xA
traffic sign is too low or too high.xA traffic sign is too bright or too dark (including electronic traffic signs).xA traffic sign is too big or too small.xThere is an object similar to the traffic sign being read (such as another traffic
sign or other signs resembling it).
xThe TSR can be set to invisible on the active driving display.
Refer to the Settings section in the Mazda Connect Owner's Manual.
▼Traffic Sign Display Indication
The following traffic signs are displayed
on the active driving display/
instrument cluster.
Speed limit signs (including auxiliary
signs)
1. Speed limit signs
2. Auxiliary sign (example)
When Driving
i-ACTIVSENSE
4-113

xAn object that reflects the radio
waves of the radar such as a
parked vehicle, guardrail, or wall is
directly next to your vehicle.
xVehicles are stopped in the area
around your vehicle such as during
heavy traffic.
xA vehicle approaching from the
front or side of your vehicle slows
down.
xA vehicle approaching from the
front or left side of your vehicle
makes a right or left turn directly in
front of your vehicle.
xA vehicle or pedestrian moves in
the parking lot or on the sidewalk
in the area surrounding your
vehicle.
xAfter making a left or right turn, an
on-coming vehicle is present.
xWhen passing an on-coming
vehicle.
xA vehicle overtakes your vehicle
while it is stopped.
xYour vehicle is in an area where
strong radio waves or electrical
noise may occur such as near a
television tower or power plant.
xUnder the following conditions, the
front side radar sensor cannot detect
approaching vehicles or it might be
difficult to detect them, and the
system may not operate normally.
xThe front side radar sensor
detection area is obstructed by a
nearby wall or vehicle.
xDirectly after the system becomes
operable.
xRadio wave interference from a
radar sensor equipped on a nearby
vehicle.
xThe approaching vehicle has any of
the following shapes.
a) The size of the vehicle body is
extremely small.
b) The vehicle height is extremely
low or high.
c) A special type of vehicle with a
complex shape
xA vehicle suddenly enters the
detection area from the front or
side of your vehicle.
xA vehicle that has stopped
suddenly starts to move.
xMultiple objects move at the same
time.
xThe vehicle is driven in bad
weather conditions such as heavy
rain, fog , snow, or sand storms.
xThe vehicle is driven on a sharp
curve or on bumpy roads.
xAn object that reflects the radio
waves of the radar such as a
parked vehicle, guardrail, or wall is
directly next to your vehicle.
xA vehicle approaches while turning
(Such as roundabout)
xThe vehicle is driven at an
extremely slow speed.
xIn the following cases, the system
turns on the i-ACTIVSENSE warning
indication/warning light and
operation of the system is stopped. If
the i-ACTIVSENSE warning
indication/warning light remains on,
have the vehicle inspected by an
expert repairer (we recommend an
Authorised Mazda Repairer) as soon
as possible.
xSome problem with the system has
occurred.
xThe front side radar sensor
installation position is greatly
deviated.
xThere is a large accumulation of
snow or ice on the front bumper
near a front side radar sensor.
xThe temperature near the radar
sensors becomes extremely hot
due to driving for a long time on
slopes during the summer.
When Driving
i-ACTIVSENSE
4-125

WARNING
Always check the surrounding area
visually before actually putting the
vehicle in reverse:
The system is only designed to assist
you in checking for vehicles at the rear
when putting the vehicle in reverse.
Due to certain limitations with the
operation of this system, the Blind Spot
Monitoring (BSM) warning indicator
lights may not
flash or it might be
delayed even though a vehicle is
behind your vehicle. Always make it
your responsibility as a driver to check
the rear.
RCTA operation
1. The RCTA system operates when
the shift lever (manual
transmission) or the selector lever
(automatic transmission) is shifted
to the reverse (R) position.
2. If there is the possibility of a
collision with an approaching
vehicle, the Blind Spot Monitoring
(BSM) warning indicator lights
flashes and the warning beep is
activated simultaneously.
Rear view monitor (vehicles with
Rear view monitor)
The RCTA warning indication in the
rearview monitor also synchronizes
with the Blind Spot Monitoring
(BSM) warning indicator light on
the door mirrors.
360°view monitor (vehicles with
360°view monitor)
The RCTA warning indication in the
360°view monitor also
synchronizes with the Blind Spot
Monitoring (BSM) warning
indicator light on the door mirrors.
Function for cancelling illumination
dimmer
If the BSM warning indicator lights turn
on when the position lights are turned
on, the brightness of the BSM warning
indicator lights is dimmed.
If the BSM warning indicator lights are
difficult to see due to glare from
surrounding brightness when travelling
on snow-covered roads or under foggy
conditions, press the dimmer
cancellation button to cancel the
dimmer and increase the brightness of
BSM warning indicator lights when
they turn on.
Refer to Instrument Panel Illumination
on page 4-27.
NOTE
xThe system may operate under the
following conditions even if a vehicle
is not approaching.
xAn object that reflects the radio
waves of the radar such as a
parked vehicle, guardrail, or wall is
directly next to your vehicle.
xA vehicle approaching from the
rear left and right side of your
vehicle slows down.
xA vehicle approaching from the
rear left and right side of your
vehicle makes a right or left turn
directly in front of your vehicle.
When Driving
i-ACTIVSENSE
4-127

xIn the following cases, it may be
difficult to view the illumination/
flashing of the Blind Spot Monitoring
(BSM) warning indicator lights
equipped on the door mirrors.
xSnow or ice adheres to the door
mirrors.
xThe front door glass is fogged or
covered in snow, frost or dirt.
xTurn off the RCTA system while
pulling a trailer or while an accessory
such as a bicycle carrier is installed to
the rear of the vehicle. Otherwise,
the radio waves emitted by the radar
will be blocked causing the system to
not operate normally.
xThe rear side radar sensor of the
RCTA may be regulated under the
radio wave related laws of the
country where the vehicle is driven. If
this system is used abroad, it may be
necessary to turn off the system.
Refer to Rear Side Radar Sensor on
page 4-224.
xIf a Mazda genuine trailer hitch is
used, the RCTA is automatically
turned off.
▼Cancelling Operation of Rear
Cross
Tra ffi c Alert (RCTA)
The RCTA can be set to inoperable.
x(If only the RCTA is turned off)
Refer to the Settings section in the
Mazda Connect Owner's Manual.
x(If the RCTA is turned off by
operating the i-ACTIVSENSE switch)
Refer to i-ACTIVSENSE Switch on
page 4-97.
NOTE
If the ignition is switched OFF while
you have cancelled the system using
the i-ACTIVSENSE switch, the system is
automatically enabled the next time
the ignition is switched ON. However,
if the system is cancelled using the
personalisation features, the system is
not automatically enabled.
When Driving
i-ACTIVSENSE
4-129

xThe selector lever is in the P (Park), N
(Neutral), or R (Reverse) position.

Under the following conditions, the
MRCC with Stop & Go function cancel
indication is displayed in the
multi-information display and a single
beep sound is heard.
xThe DSC has operated.xThe Smart Brake Support (SBS) has
operated.
xWhen travelling on a downslope for
a long period of time.
xThere is a problem with the system.xThe parking brake is automatically
applied during stop hold control.
xThe front radar sensor cannot detect
target objects (during rain, fog , snow
or other inclement weather
conditions, or when the radiator
grille is dirty).
xThe parking brake is applied.xAny of the doors is opened.xThe driver's seat belt is unfastened.xThe operation frequency of the
braking by the MRCC with Stop &
Go function control is high.
Resuming control
If the MRCC with Stop & Go function
system is cancelled, you can resume
control at the previously set speed by
pressing the RES switch and after all of
the operation conditions have been
met.
NOTE
If the set speed is not indicated in the
display, the control does not resume
even if the RES switch is pressed.
Turning off the system
When the MRCC switch is pressed
while the MRCC is operating, the
MRCC turns off.
▼Stop Hold Control
While in headway control using the
MRCC with Stop & Go function
system, your vehicle will stop when a
vehicle ahead stops. When the vehicle
is stopped and the stop hold control
operates, the MRCC with Stop & Go
function indicator light turns on.
NOTE
xIf the MRCC with Stop & Go
function system is cancelled during
stop hold control, the vehicle is held
in its stopped position.
xThe parking brake is automatically
applied and the vehicle is held in its
stopped position when 10 minutes
have elapsed since the stop hold
control operated. At this time, the
MRCC with Stop & Go function
system is cancelled.
xIf the i-stop operation conditions are
met during stop hold control, the
engine stops even though the brake
pedal is not depressed.
Refer to i-stop on page 4-11.
xThe brake lights turn on during stop
hold control.
To resume driving
After the vehicle ahead starts moving
while your vehicle is stopped under
stop hold control, press the RES switch
or depress the accelerator pedal to
cancel the stop hold control and
resume driving.
When Driving
i-ACTIVSENSE
4-147