2019 MAZDA MODEL CX-30 display

Instrument Cluster and
Display
▼Instrument Cluster and Display

ƒInstrument Cluster.......... page 4-21
„Active Driving Display..... page 4-39
Instrument Cluster
▼Instrument Cluster

ƒTachometer.................... page 4-21
„Multi-information Display...............
..................................... page 4-23
…Engine Coolant Temperature
Gauge............................ page 4-25
†Fuel Gauge..................... page 4-26
‡Instrument Panel Illumination
Switch............................ page 4-27
ˆSpeedometer..................page 4-21
‰TRIP Switch.................... page 4-25
▼Speedometer
The speedometer indicates the speed
of the vehicle.
▼Tachometer
The tachometer shows engine speed in
thousands of revolutions per minute
(rpm).
When Driving
Instrument Cluster and Display
4-21

CAUTION
Do not run the engine with the
tachometer needle in the RED ZONE.
This may cause severe engine damage.

1. STRIPED ZONE*1
2. RED ZONE*1
*1 The range varies depending on the type of
gauge.
NOTE
When the tachometer needle enters
the STRIPED ZONE, this indicates to
the driver that the gears should be
shifted before entering the RED ZONE.
When Driving
Instrument Cluster and Display
4-22

▼Multi-information Display
1. Multi-information Display
2. INFO switch

The multi-information display indicates the following information.
xSpeedometerxOdometerxTr i p m e te rxOutside temperaturexDistance-to-emptyxAverage fuel economyxCurrent fuel economyxDeceleration Regeneration Charge Display (M Hybrid)xi-ACTIVSENSE DisplayxVehicle Speed Alarm*
xDoor-Ajar/Liftgate-Ajar Warning Indication*1
xMessage Display
*1 Displayed when opening door/liftgate.
When Driving
Instrument Cluster and Display
*Some models.4-23

The screen content changes each time the INFO switch is pressed.
1. Basic display
2. Drive information display
3. i-ACTIVSENSE display
4. Message display
*1
*1 Displayed only when a warning occurs.

The type of display for the fuel economy and the maximum driving distance can be
changed.
Refer to the Settings section in the Mazda Connect Owner's Manual.
When Driving
Instrument Cluster and Display
4-24

▼Odometer, Trip Meter and Trip
Meter Selector
You can switch between the odometer
and trip meter display using the TRIP
switch.

1. TRIP switch
2. Odometer display
3. Trip meter A display
4. Trip meter B display
Odometer
The odometer records the total
distance the vehicle has been driven.
Tr i p m e t e r
The driving distance for a specified
interval is indicated. Two types (TRIP A,
TRIP B) of interval distance and the
average fuel economy for each can be
measured.

For instance, trip meter A can record
the distance from the point of origin,
and trip meter B can record the
distance from where the fuel tank is
filled.

When trip meter A is selected, TRIP A
will be displayed. When trip meter B is
selected, TRIP B will be displayed.

The trip meter and average fuel
economy can be reset by pressing the
TRIP switch for 1.5 seconds or more
while in each mode.
NOTE
xOnly the trip meters record tenths of
kilometres (miles).
xThe trip record will be erased when:
xThe power supply is interrupted
(blown fuse or the battery is
disconnected).
xThe vehicle is driven over 9999.9
km (mile).
▼Engine Coolant Temperature
Gauge
Displays the engine coolant
temperature. The blue range of the
gauge indicates that the engine coolant
temperature is low, and the red range
of the gauge indicates that the engine
coolant temperature is high and
overheating.

When Driving
Instrument Cluster and Display
4-25

CAUTION
When the engine coolant temperature
gauge needle is in the red range, the
engine coolant temperature is
extremely high. Drive slowly to reduce
engine load. If the engine coolant
temperature gauge needle is in the red
range, there is the possibility of
overheating. Park the vehicle in a safe
place immediately and take
appropriate measures.
Refer to Overheating on page 7-44.
NOTE
xIf the engine or engine coolant
temperature is high or low, the
engine output may be restricted to
protect the engine.
xDuring normal driving , the engine
coolant temperature stabilizes at 100
°C (210 °F) or less, and the gauge
indicates a range lower than 100 °C
(210 °F).
▼Fuel Gauge
The fuel gauge shows approximately
how much fuel is remaining in the tank
when the ignition is switched ON. We
recommend keeping the tank over 1/4
full.

1. Full
2. 1/4 Full
3. Empty

If the low fuel warning light illuminates
or the fuel level is very low, refuel as
soon as possible.
If inconsistency in engine performance
or stalling occurs due to low fuel level
conditions, refuel the vehicle as soon
as possible and add at least 10 L (2.7
US gal, 2.2 Imp gal) of fuel.
Refer to Low Fuel Warning Indication/
Warning Light on page 7-58.
NOTE
xAfter refuelling, it may require some
time for the indicator to stabilize. In
addition, the indicator may deviate
while driving on a slope or curve
since the fuel moves in the tank.
When Driving
Instrument Cluster and Display
4-26

xThe direction of the arrow ()
indicates that the fuel-filler flap is on
the left side of the vehicle.
▼Instrument Panel Illumination
(Without auto-light control)
When the lights are turned on with the
ignition switched ON, the brightness of
the instrument panel illumination is
dimmed.
(With auto-light control)
When the lights are turned on with the
ignition switched ON, the brightness of
the instrument panel illumination is
dimmed. However, when the light
sensor detects that the surrounding
area is bright such as when the lights
are turned on in the daytime, the
instrument panel illumination does not
dim.
NOTE
x(With auto-light control)
When the ignition is switched ON in
the early evening or at dusk, the
instrument panel illumination is
dimmed for several seconds until the
light sensor detects the brightness of
the surrounding area, however, the
dimming may cancel after the
brightness is detected.
xWhen the lights are turned on, the
lights-on indicator light in the
instrument cluster turns on.
Refer to Headlights on page 4-54.
The brightness of the instrument panel
and instrument panel illuminations can
be adjusted by pressing the instrument
panel illumination switch while the
instrument panel illumination is
dimmed.
xThe brightness increases by pressing
the + switch.
xThe brightness decreases by pressing
the - switch. If you press the - switch
while the instrument cluster is at
maximum dimness, a sound is
activated to notify you that the
current dimmer setting is at
maximum dimness.

1. Bright
2. Dim
Function for cancelling illumination
dimmer
The illumination dimmer can be
cancelled by pressing the + switch
while the instrument cluster is at
maximum dimness and while the
ignition is switched ON. If you press
the + switch again while the
illumination dimmer is cancelled, a
sound is activated to notify you that it
is cancelled. If the instrument cluster's
visibility is reduced due to glare from
surrounding brightness, cancel the
illumination dimmer.
NOTE
xWhen the illumination dimmer is
cancelled, the instrument cluster
cannot be dimmed even if the lights
are turned on.
xWhen the illumination dimmer is
cancelled, the screen in the centre
display switches to constant display
of the daytime screen.
When Driving
Instrument Cluster and Display
4-27

▼Outside Temperature Display
When the ignition is switched ON, the
outside temperature is displayed.

NOTE
xUnder the following conditions, the
outside temperature display may
differ from the actual outside
temperature depending on the
surroundings and vehicle conditions:
xSignificantly cold or hot
temperatures.
xSudden changes in outside
temperature.
xThe vehicle is parked.xThe vehicle is driven at low speeds.
Changing the Temperature Unit of the
Outside Temperature Display
The outside temperature unit can be
switched between Celsius and
Fahrenheit.
Settings can be changed by operating
the centre display screen.
Refer to the Settings section in the
Mazda Connect Owner's Manual.
NOTE
When the temperature unit indicated
in the outside temperature display is
changed, the temperature unit
indicated in the engine coolant gauge
display changes in conjunction with it.
Outside Temperature Warning*
When the outside temperature is low,
the indication flashes and a beep
sound is heard to warn the driver of
the possibility of icy roads.
If the outside temperature is lower
than about 4 °C (39 °F), the outside
temperature display and the
mark
flashes for about 3 seconds and a beep
sound is heard once.
NOTE
If the outside temperature is lower
than -20 °C (-4 °F), the beep sound
does not operate. However, the
mark illuminates.
▼Distance-to-empty
This displays the approximate distance
you can travel on the remaining fuel
based on the fuel economy.
The distance-to-empty will be
calculated and displayed every second.

NOTE
xEven though the distance-to-empty
display may indicate a
sufficient
amount of remaining driving distance
before refuelling is required, refuel as
soon as possible if the fuel level is
very low or the low fuel warning light
illuminates.
xThe display will not change unless
you add more than approximately 9
L (2.3 US gal, 1.9 Imp gal) of fuel.
When Driving
Instrument Cluster and Display
4-28*Some models.