2019 MAZDA MODEL CX-30 warning

Petrol Particulate Filter
(SKYACTIV-X 2.0)
▼Petrol Particulate Filter
The petrol particulate filter collects and
removes most of the particulate matter
(PM) in the exhaust gas of a petrol
engine.
PM collected by the petrol particulate
filter is cleared during normal driving ,
however, PM may not be removed and
the petrol particulate filter warning
indication/warning light may
illuminate under the following
conditions:
xIf the vehicle is driven at 20 km/h
(12 mph) or less continuously.
xIf the vehicle is repeatedly driven for
a short period of time (30 minute or
less) or driven while the engine is
cold.
xIf the vehicle is idled for a long time.
Refer to Petrol Particulate Filter
Warning Indication/Warning Light on
page 7-54.
When Driving
Petrol Particulate Filter
4-236

Diesel Particulate Filter
(SKYACTIV-D 1.8)
▼Diesel Particulate Filter
The diesel particulate filter collects and
removes most of the particulate matter
(PM) in the exhaust gas of a diesel
engine.
PM collected by the diesel particulate
filter is cleared during normal driving ,
however, PM may not be removed and
the diesel particulate filter warning
indication/warning light may
illuminate under the following
conditions:
xIf the vehicle is driven at 15 km/h (9
mph) or less continuously.
xIf the vehicle is repeatedly driven for
a short period of time (10 minute or
less) or driven while the engine is
cold.
xIf the vehicle is idled for a long time.
Refer to Diesel Particulate Filter on
page 7-54.
When Driving
Diesel Particulate Filter
4-237

Rear View Monitor*
▼Rear View Monitor
The rear view monitor provides visual
images of the rear of the vehicle when
reversing.
WARNING
Always drive carefully confirming the
safety of the rear and the surrounding
conditions by looking directly with
your eyes:
Reversing the vehicle by only looking at
the screen is dangerous as it may cause
an accident or a collision with an
object. The rear view monitor is only a
visual assist device when reversing the
vehicle. The images on the screen may
be
different from the actual conditions.
CAUTION
¾Do not use the rear view monitor
under the following conditions:
Using the rear view monitor under
the following conditions is
dangerous and could result in injury
or vehicle damage or both.
¾Icy or snow-covered roads.
¾Tyre chains or a temporary spare
tyre is installed.
¾The vehicle is on a road incline.
¾When the display is cold, images
may course across the monitor or the
screen and may be dimmer than
usual, which could cause difficulty in
confirming the surrounding
conditions of the vehicle. Always
drive carefully confirming the safety
of the rear and the surrounding
conditions by looking directly with
your eyes.
¾Do not apply excessive force to the
camera. The camera position and
angle may deviate.
¾Do not disassemble, modify, or
remove it as it may no longer be
waterproof.
¾The camera cover is made of plastic.
Do not apply degreasing agents,
organic solvents, wax, or glass
coating agents to the camera cover.
If any are spilled on the cover, wipe
off with a soft cloth immediately.
¾Do not rub the camera cover
forcefully with an abrasive or hard
brush. The camera cover or lens may
be scratched which might affect the
images.
NOTE
xIf water, snow, or mud is stuck on
the camera lens, wipe it
off using a
soft cloth. If it cannot be wiped off,
use a mild detergent.
xIf the camera temperature changes
rapidly (Hot to cold, cold to hot), the
rear view monitor may not operate
correctly.
xWhen replacing the tyres, consult an
expert repairer (we recommend an
Authorised Mazda Repairer).
Replacing the tyres could result in
deviation of the guide lines which
appear on the display.
xIf the vehicle's front, side, or rear has
been involved in a collision, the
alignment of the rear view parking
camera (location, installation angle)
may have deviated. Always consult
an expert repairer (we recommend
an Authorised Mazda Repairer) to
have the vehicle inspected.
When Driving
Rear View Monitor
4-238*Some models.

Parking Sensor System*
▼Parking Sensor System
The parking sensors use ultrasonic sensors which detect obstructions around the
vehicle when the vehicle is driven at low speeds, such as during garage or parallel
parking, and a buzzer sound and detection indicator notify the driver of the
approximate distance from the vehicle to the surrounding obstruction.

1. Front ultrasonic sensor*
2. Front corner ultrasonic sensor*
3. Rear ultrasonic sensor
4. Rear corner ultrasonic sensor
5. Rear side ultrasonic sensor
*
WARNING
Do not rely completely on the parking sensor system and be sure to
confirm the
safety around your vehicle visually when driving:
This system can assist the driver in operating the vehicle in the forward and
backward directions while parking. The detection ranges of the sensors are limited,
therefore, driving the vehicle while relying only on the system may cause an
accident. Always
confirm the safety around your vehicle visually when driving.
CAUTION
¾Do not install any accessories within the detection ranges of the sensors. It may
affect the system operation.
¾Depending on the type of obstruction and the surrounding conditions, the
detection range of a sensor may narrow, or the sensors may not be able to detect
obstructions.
NOTE
xThe system may not operate normally under the following conditions:
xMud, ice, or snow is adhering to the sensor area (Returns to normal operation
when removed).
When Driving
Parking Sensor System
4-252*Some models.

3. Right rear corner ultrasonic sensor
gauge/Right rear side ultrasonic
sensor gauge
*
4. Rear ultrasonic sensor gauge
5. Left rear corner ultrasonic sensor
gauge/Left rear side ultrasonic
sensor gauge
*
6. Left front corner ultrasonic sensor
gauge
NOTE
The detection indicator can switch
between display and non-display.
Refer to the Settings section in the
Mazda Connect Owner's Manual.
System problem notification
The indication displays if the system
has a malfunction.
Without 360°view monitor
With 360°view monitor
Check the reason for the indication
displaying on the centre display or
multi-information display.
Refer to If a Warning Light Turns On or
Flashes on page 7-49.
When Driving
Parking Sensor System
*Some models.4-257

▼Parking Sensor Warning Beep
Informs the driver of the approximate distance from the vehicle to the obstruction
using warning beeps depending on the distance. If multiple obstructions are
detected at the same time, warning beeps are activated according to the distance to
the nearest obstruction. The warning beeps are activated as follows while the system
is operating. However, the warning beeps are not activated while the seat belt
reminder is operating.
Front ultrasonic sensor
*, Rear ultrasonic sensor
Distance De-
tection areaDistance between vehicle and obstruction
Beeper sound*1Front ultrasonic sensorRear ultrasonic sensor
Farthest dis-
tanceApprox. 100Š60.0 cm
(39.3Š23.6 in)
Approx. 150Š60.0 cm
(59.0Š23.6 in)
Slow intermittent
sound
Far distanceApprox. 60.0Š45.0 cm
(23.6Š17.7 in)
Approx. 60.0Š45.0 cm
(23.6Š17.7 in)
Medium intermit-
tent sound
Middle dis-
tanceApprox. 45.0Š35.0 cm
(17.7Š13.7 in)
Approx. 45.0Š35.0 cm
(17.7Š13.7 in)
Fast intermittent
sound
When Driving
Parking Sensor System
4-258*Some models.

Distance Detection
areaDistance between vehicle and obstruction
Beeper sound*1Front corner ultrasonic sensor/Rear corner,
Rear side ultrasonic sensor
Close distanceWithin approx. 25 cm (9.8 in)
Continuous sound
*1 The rate at which the intermittent sound beeps increases as the vehicle approaches the obstruction.
NOTE
xIf an obstruction in the same area excluding the close area is detected
continuously for 6 seconds or longer, only the warning beeps stop activating.
(Detection is indicated) If the detection area changes to the close side, the
warning beeps resumes. (If the detection area changes to the far side, the warning
beeps remain off)
xThe sound volume (each of front and rear) can be changed.
Refer to the Settings section in the Mazda Connect Owner's Manual.
▼When Warning Indicator/Beep is Activated
The system notifies the driver of an abnormality by activating the beep sound and
the indicator light.
Indicator/Beep How to check
A message indicating a sys-
tem malfunction or sensor
malfunction is displayed.There may be a problem with the system. Have your vehicle inspected
by an expert repairer (we recommend an Authorised Mazda Repairer)
as soon as possible.
A message indicating that the
sensor is dirty is displayed.Remove any foreign matter from the sensor area. If the system does not
recover, have the vehicle inspected by an expert repairer (we recom-
mend an Authorised Mazda Repairer).
A certain obstruction detec-
tion indication is continuous-
ly displayed.Foreign matter may have gotten on the sensor area corresponding to
the detection indicator. If the system does not recover, have the vehicle
inspected by an expert repairer (we recommend an Authorised Mazda
Repairer).
When Driving
Parking Sensor System
4-260

NOTE
The air conditioner may not function
when the outside temperature
approaches 0 °C (32 °F).
Air intake selector switch
This switch controls the source of air
entering the vehicle.

Outside or recirculated air positions
can be selected. Press the switch to
select outside/recirculated air
positions.
Recirculated air position (indicator
light illuminated)
Outside air is shut off. Use this position
when going through tunnels, driving in
congested
traffic (high engine exhaust
areas) or when quick cooling is
desired.
Outside air position (indicator light
turned off)
Outside air is allowed to enter the
cabin. Use this mode for ventilation or
windscreen defrosting.
WARNING
Do not use the position (indicator
light turns on) in cold or rainy
weather:
Using the
position (indicator light
turns on) in cold or rainy weather is
dangerous as it will cause the windows
to fog up. Your vision will be
hampered, which could lead to a
serious accident.
Windscreen defroster switch
Press the switch to defrost the
windscreen and front door windows.
Refer to Windscreen Defrosting and
Defogging on page 5-7.
Rear window defogger switch
Press the rear window defogger switch
to defrost the rear window.
Refer to Rear Window Defogger on
page 4-66.
▼Heating
1. Press the switch.
2. Set the air intake selector to the
outside air position (indicator light
turns off).
3. Set the temperature control dial to
the hot position.
4. Set the fan control dial to the
desired speed.
5. If dehumidified heating is desired,
turn on the air conditioner.
NOTE
xIf the windscreen fogs up easily, press
the
switch.xIf cooler air is desired at face level,
press the
switch and adjust the
temperature control dial to maintain
maximum comfort.
xThe air to the
floor is warmer than air
to the face (except when the
temperature control dial is set at the
extreme hot or cold position).
▼Cooling
1. Press the switch.
2. Set the temperature control dial to
the cold position.
3. Set the fan control dial to the
desired speed.
4. Turn on the air conditioner by
pressing the A/C switch.
5. After cooling begins, adjust the fan
control dial and temperature
control dial as needed to maintain
maximum comfort.
Interior Features
Air-Conditioning System
5-6