2019 MAZDA MODEL CX-30 check oil

support rod hole indicated by the
arrow to hold the bonnet open.

1. Pad
2. Support rod
▼Closing the Bonnet
CAUTION
>&
SKYACTIV-X 2.0)
Do not close the bonnet with the
engine cover open. Otherwise, the
engine cover may fall and cause injury.
For the opening/closing of the engine
cover, refer to the “Engine
Compartment Overview” 6-19.
1. Check under the bonnet area to
make certain all
filler caps are in
place and all loose items (e.g.
tools, oil containers, etc.) have
been removed.
2. Lift the bonnet, grasp the padded
area on the support rod, and secure
the support rod in the clip. Verify
that the support rod is secured in
the clip before closing the bonnet.

1. Clip

3. Lower the bonnet slowly to a height
of about 20 cm (7.9 in) above its
closed position and then let it drop.
CAUTION
When closing the bonnet, do not push
it excessively such as by applying your
weight. Otherwise, the bonnet could
be deformed.
Maintenance and Care
Owner Maintenance
6-18

1. Drive to the side of the road and
park off the right-of-way on level
ground.
2. Turn off the engine and wait 5
minutes for the oil to drain back
into the sump.
3. Inspect the engine oil level (page
6-27). If it's low, add the
appropriate amount of engine oil
while being careful not to overfill.
CAUTION
Do not run the engine if the oil
level is low. Otherwise, it could
result in extensive engine damage.
4. Start the engine and check the
warning light.

If the light remains illuminated even
though the oil level is normal or after
adding oil, stop the engine
immediately and have your vehicle
towed to an expert repairer (we
recommend an Authorised Mazda
Repairer).
▼High Engine Coolant Temperature
Warning Indication
Displays if the engine coolant
temperature has increased excessively.
“Elevated Engine Coolant Temp. Drive
Slowly” displayed
Drive slowly to reduce engine load
until you can find a safe place to stop
the vehicle and wait for the engine to
cool down.
“Excessive Engine Coolant Temp. Stop
the Vehicle in a Safe Location”
displayed
This indicates the possibility of
overheating. Park the vehicle in a safe
place immediately and stop the
engine.
Refer to Overheating on page 7-44.
CAUTION
Do not drive the vehicle with the high
engine coolant temperature warning
light illuminated. Otherwise, it could
result in damage to the engine.
▼Power Steering Malfunction
Indication/Indicator Light
The message is displayed if the electric
power steering has a malfunction.
If the message is displayed, stop the
vehicle in a safe place and do not
operate the steering wheel. There is no
problem if the indication turns off
when the engine is restarted after
some time has passed. If the indication
displays even after the engine is
restarted, contact an expert repairer
(we recommend an Authorised Mazda
Repairer) if the message is displayed
continuously.
NOTE
xIf the message is displayed, the
power steering will not operate
normally. In this case, the steering
wheel can still be operated,
however, the operation may feel
heavy compared to normal, or the
steering wheel could vibrate when
turning.
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
7-51

at an expert repairer (we recommend
an Authorised Mazda Repairer).
xWhen there is a malfunction in the
AWD system.
“Excessive AWD System Load. Drive
Slowly Until Warning Light Turns Off.
Vehicle Now in Front Wheel Drive” is
displayed/When the light is flashing
The indication is displayed/the light
flashes under the following conditions.
Park the vehicle in a safe place and
check that the warning indication light
turns
off/ the warning light stops
flashing, and then drive the vehicle.
Contact an expert repairer (we
recommend an Authorised Mazda
Repairer) if the indication is
continuously displayed.
xWhen the differential oil temperature
is excessively high.
xWhen there is a large difference
between the front and rear wheel
rotation, such as when trying to
remove the vehicle from mud.
“Mismatched Tyre Diameters. Vehicle
Now in Front Wheel Drive” is
displayed/When the light is turned on
The indication is displayed/the light
turns on under the following
conditions. Inspect the tyre sizes or
tyre pressures on all 4 wheels. Contact
an expert repairer (we recommend an
Authorised Mazda Repairer) if the
indication remains on or the warning
light remains illuminated.
xWhen any of the tyre diameter is
different.
xWhen any of the tyre pressure is
incorrect.
▼120 km/h Warning Light*
The 120 km/h warning light
illuminates when the vehicle speed
exceeds 120 km/h.
Action to be taken
Lower the vehicle speed.
▼Tyre Pressure Monitoring System
(TPMS) Warning Indication/
Warning Light (Flashing)
*
If there is a problem with the TPMS or
the voltage of a tyre pressure sensor
decreases, the TPMS warning light
flashes and a message is displayed on
the multi-information display. Have
your vehicle inspected by an expert
repairer (we recommend an
Authorised Mazda Repairer).
WARNING
Do not drive the vehicle at high
speeds if the TPMS warning light turns
on or flashes:
Driving the vehicle at high speeds
while the TPMS warning light is turned
on or
flashing is dangerous because
the brake performance and the
steering wheel operability will be
reduced. If the vehicle is driven at high
speeds or the brakes are suddenly
applied, it could lead to an accident.
Gradually apply the brakes to lower the
vehicle's speed.
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
*Some models.7-57

perform the applicable procedure
(page 3-8).
▼Power Liftgate Warning Beep*
If system operation precautions are
necessary, the driver is notified by the
warning sound.
Warning beep What to check
The beep sounds 3
timesThe conditions re-
quired for the power
liftgate to operate have
not been met, such as
an object being stuck
in the liftgate.
The beep sound con-
tinuesThe vehicle is being
driven with the liftgate
open. Stop the vehicle
and close the liftgate.
▼Low Fuel Warning Beep
When the low fuel warning light
flashes, a warning beep is activated
once at the same time.
▼Electronic Steering Lock Warning
Beep
The warning beep operates if the
steering wheel is not unlocked after the
push button start is pressed. (page
4-4)
▼Brake System Warning Beep (With
M Hybrid)
A warning beep is activated if a
problem with the brake system occurs
and the brakes may not work as
intended. Decelerate the vehicle while
checking the safety of the surrounding
area, and park the vehicle in a safe
place. After stopping the vehicle,
contact an expert repairer (we
recommend an Authorised Mazda
Repairer).
▼Brake Override Warning Beep
A warning beep is activated when the
accelerator pedal and brake pedal are
depressed at the same time while
driving. Only depress the brake pedal.
▼Vehicle Problem Warning Beep
If any of the following problems occur,
a warning beep is activated. Check the
information regarding the warning
indication in the instrument cluster or
on the centre display.
xAutomatic transmission problemxIncrease in automatic transmission
internal temperature
xM Hybrid problemxBrake fluid amount decreasexEngine oil level sensor problemxElectric Parking Brake (EPB) problemxEngine hydraulic pressure decreasexEngine coolant temperature increasexEngine system problem
▼Shift Position Warning Beep
A sound is activated when the push
button start is pressed while the
selector lever is in a position other
than P, and the ignition is switched to
ACC. Check the selector lever
position.
▼Ignition Not Off Reminder
Warning Beep (With M Hybrid)
A warning beep is activated
continuously if the driver's door is
opened with the selector lever in a
position other than the P or N
position. Shift the selector lever to the
P or N position, or close the driver's
door.
▼i-stop Warning Beep*
xIf the driver's door is opened while
engine idling is stopped, the warning
sound operates to notify the driver
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
*Some models.7-69

Item Capacity
Fuel tankFWD51.0 L (13.5 US gal, 11.2 Imp
gal)
AWD48.0 L (12.7 US gal, 10.6 Imp
gal)
Check oil and
fluid levels with dipsticks or reservoir gauges.
▼Dimensions
Item Vehicle specification
Overall length 4,395 mm (173.0 in)
Overall width 1,795 mm (70.7 in)
Overall height 1,540 mm (60.6 in)
Front tread 1,565 mm (61.6 in)
Rear tread 1,565 mm (61.6 in)
Wheelbase 2,655 mm (104.5 in)
▼Light Bulbs
The LED bulb cannot be replaced. Consult an expert repairer (we recommend an
Authorised Mazda Repairer) when the replacement is necessary.
Exterior light
Light bulbCategory
Wattage
UN-R*1 (SAE)
xHeadlightsxPosition lightsxFront direction indicator lightsxSide direction indicator lightsxHigh-mount brake lightxRear direction indicator lightsxBrake lightsxTail lightsxReverse lights
xRear fog light*
xNumber plate lightsLEDŠ (Š)
Running lights
*LED type LEDŠ (Š)
Bulb type
21
*2W21/5W (7444)
*1 UN-R stands for United Nations Regulation.*2
Double-filament light bulb, however, only 21 W
filament bulb is used in the running lights.
Specifications
Specifications
*Some models.9-9