2019 MAZDA MODEL CX-30 air condition

StatusIndicator light
Beep sound
statusOn/flashing conditions
Green Red Flash interval
Malfunction Turns off Turns onŠ3 beeps
(Slow intermit-
tent sound)
xA system malfunction is
detected.
xThe remaining power of
the built-in battery is low.
CAUTION
If the indicator light (red) re-
mains on constantly, the sys-
tem will not operate normal-
ly. Have the vehicle inspected
at an expert repairer (we rec-
ommend an Authorised Maz-
da Repairer) as soon as possi-
ble.
Call being
made with call
centreFlashes Turns offSlow
(0.5 second
intervals)The beep does
not sound, but
the ringback
tone can be
heard.An emergency call is being
made by the Mazda
ERA-GLONASS.
Vehicle infor-
mation is be-
ing transmittedFlashes Turns
offSomewhat
quick
(0.3 second
intervals)Continuous in-
termittent
soundVehicle information is being
transmitted to the call centre.
Start of voice
callTu r n s o n Tu r n s o ffŠ1 beep
During a voice call with the
call centre.
During voice
callTu r n s o n Tu r n s
offŠŠ
Connection
failureFlashes Turns onQuick
(0.15 second
intervals)3 beeps
(Fast intermit-
tent sound)When an emergency call fails
to connect.
▼Te s t M o d e
The test mode function makes sure that the Mazda ERA-GLONASS can operate
normally.
Have your vehicle tested at an Authorised Mazda Repairer when performing the test
mode.
Method to start test mode
Switch the ignition ON while the parking brake is applied, and wait 2 minutes with
the vehicle stopped.
If Trouble Arises
Mazda
ERA-GLONASS
7-20

Route the jumper leads away from parts that will be moving:
Connecting a jumper lead near or to moving parts (cooling fans, belts) is dangerous.
The lead could get caught when the engine starts and cause serious injury.
CAUTION
Use only a 12 V booster system. You can damage a 12 V starter, ignition system, and
other electrical parts beyond repair with a 24 V power supply (two 12 V batteries in
series or a 24 V motor generator set).
1. Move the booster vehicle so that its battery is as close as possible to your
vehicle's battery.
2. Make sure that the power such as for the headlights and air conditioner is turned
off.
3. Remove the battery cover.
4. Turn off the booster vehicle's engine and connect the jumper leads in the
following order.
Make sure that the jumper leads are securely connected so that they do not
disconnect due to engine vibrations.
1st lead
Positive (+) terminal on the discharged battery
Positive (+) terminal on booster vehicle's battery
2nd lead
Negative (-) terminal on booster vehicle's battery
If Trouble Arises
Battery Runs Out
7-40

Overheating
▼Overheating
If the engine coolant temperature
gauge indicates overheating and the
high engine coolant temperature
warning indication is displayed, the
vehicle loses power or you hear a loud
knocking or pinging noise, the engine
is probably too hot.
WARNING
Pull over to a safe location, then
switch the ignition off and make sure
the fan is not running before
attempting to work near the cooling
fan:
Working near the cooling fan when it is
running is dangerous. The fan could
continue running
indefinitely even if
the engine has stopped and the engine
compartment temperature is high. You
could be hit by the fan and seriously
injured.
Do not remove either
cooling system cap when the engine
and radiator are hot:
When the engine and radiator are hot,
scalding coolant and steam may shoot
out under pressure and cause serious
injury.
Open the bonnet ONLY after steam is
no longer escaping from the engine:
Steam from an overheated engine is
dangerous. The escaping steam could
seriously burn you.
If the engine coolant temperature
gauge indicates overheating and the
high engine coolant temperature
warning indication is displayed:

1. Drive safely to the side of the road
and park off the right-of-way.
2. Put a vehicle with an automatic
transmission in park (P), a manual
transmission in neutral.
3. Apply the parking brake.
4. Turn off the air conditioner.
5. Check whether coolant or steam is
escaping from the engine
compartment.

If steam is coming from the engine
compartment:
Do not go near the front of the
vehicle. Stop the engine.
Wait until the steam dissipates,
then open the bonnet and start the
engine.

If neither coolant nor steam is
escaping:
Open the bonnet and idle the
engine until it cools.
CAUTION
If the cooling fan does not operate
while the engine is running, the
engine temperature will increase.
Stop the engine and call an expert
repairer (we recommend an
Authorised Mazda Repairer).
6. Make sure the cooling fan is
operating, then turn off the engine
after the temperature has
decreased.
7. When cool, check the coolant level.
If Trouble Arises
Overheating
7-44

Towing Description
▼Towing Description
We recommend that towing be done
only by an expert repairer (we
recommend an Authorised Mazda
Repairer) or a commercial tow-truck
service.

Proper lifting and towing are necessary
to prevent damage to the vehicle.
Particularly when towing a AWD
vehicle, where all the wheels are
connected to the drive train, proper
transporting of the vehicle is absolutely
essential to avoid damaging the drive
system. Government and local laws
must be followed.
1. Wheel dollies

A towed FWD vehicle should have its
drive wheels (front wheels)
off the
ground. If excessive damage or other
conditions prevent this, use wheel
dollies.

When towing a FWD vehicle with the
rear wheels on the ground, release the
parking brake.
Refer to Electric Parking Brake (EPB) on
page 4-70.

A towed AWD vehicle must have all its
wheels
off the ground.
WARNING
Always tow a AWD vehicle with all
four wheels
off the ground:
Towing a AWD vehicle with either the
front or rear wheels on the ground is
dangerous as the drive train could be
damaged, or the vehicle could trail
away from the tow truck and cause an
accident. If the drive train has been
damaged, transport the vehicle on a
flatbed truck.
CAUTION
¾Do not tow the vehicle pointed
backward with driving wheels on the
ground. This may cause internal
damage to the transmission.
¾Do not tow with sling-type
equipment. This could damage your
vehicle. Use wheel-lift or flatbed
equipment.
If Trouble Arises
Emergency Towing
7-46

Rear

CAUTION
Do not use excessive force as it
may damage the cap or scratch the
painted bumper surface.
NOTE
Remove the cap completely and
store it so as not to lose it.
3. Securely install the towing eyelet
using the wheel brace or
equivalent.
Consult an expert repairer (we
recommend an Authorised Mazda
Repairer).
Front
1. Wheel brace
2. Towing eyelet
Rear
1. Wheel brace
2. Towing eyelet
4. Hook the towing rope to the
towing eyelet.
CAUTION
¾If the towing eyelet is not
securely tightened, it may loosen
or disengage from the bumper
when towing the vehicle. Make
sure that the towing eyelet is
securely tightened to the
bumper.
¾Be careful not to damage the
towing eyelet and towing hook,
vehicle body, or transmission
system when towing under the
following conditions:
¾Do not tow a vehicle heavier
than yours.
¾Do not suddenly accelerate
your vehicle as it will apply a
severe shock to the towing
eyelet and towing hook or
rope.
¾Do not attach any rope other
than to the towing eyelet and
towing hook.
If Trouble Arises
Emergency Towing
7-48

▼Brake Override Warning Indication
This message is displayed when the
accelerator pedal and brake pedal are
depressed at the same time while
driving.
Release the accelerator pedal and
depress the brake pedal.
▼Check Engine Indication/Light
If this light illuminates while driving ,
the vehicle may have a problem. It is
important to note the driving
conditions when the light illuminated
and consult an expert repairer (we
recommend an Authorised Mazda
Repairer).
The check engine light may illuminate
in the following cases:
xThe engine's electrical system has a
problem.
xThe emission control system has a
problem.
x(Except SKYACTIV-D 1.8)
xThe fuel tank level being very low
or approaching empty.
xThe
fuel-filler cap is missing or not
tightened securely.
If the check engine light remains on, or
it flashes continuously , do not drive at
high speeds and consult an expert
repairer (we recommend an
Authorised Mazda Repairer) as soon as
possible.
WARNING
If the check engine light turns on, do
not disconnect the battery leads.
If the battery leads are disconnected
and then reconnected, the engine
could be damaged and catch on
fire.
▼i-stop Warning Indication/
Warning Light (Amber)*
When the light is turned on
xA problem in the system may be
indicated under the following
conditions. Have your vehicle
inspected at an expert repairer (we
recommend an Authorised Mazda
Repairer).
xThe light does not turn on when
the ignition is switched ON.
x(Except European model)
If the i-stop warning light (amber)
remains on while the engine is
running , the battery performance
may have decreased. Have your
vehicle inspected at an expert
repairer (we recommend an
Authorised Mazda Repairer).
When the light is flashing
The light continues to flash if the
system has a malfunction. Have your
vehicle inspected at an expert repairer
(we recommend an Authorised Mazda
Repairer).
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
*Some models.7-53

CAUTION
If the vehicle is continually driven as
usual with the diesel particulate filter
warning light turned on, PM increases
and the warning light may start
flashing. If the diesel particulate filter
warning light starts flashing, have the
vehicle inspected immediately at an
expert repairer (we recommend an
Authorised Mazda Repairer). If the
vehicle is not inspected and continues
to be driven, the engine may
malfunction.
NOTE
xWhen the diesel particulate filter
warning light
flashes, the engine
output is restricted to protect the
diesel particulate
filter.
xThe engine sound and exhaust gas
smell may change when PM is being
removed while driving.
▼Automatic Transmission Warning
Indication/Warning Light*
The indication/light illuminates when
the transmission has a problem.
CAUTION
If the automatic transmission warning
indication/light illuminates, the
transmission has an electrical problem.
Continuing to drive your Mazda in this
condition could cause damage to your
transmission. Consult an expert
repairer (we recommend an
Authorised Mazda Repairer) as soon as
possible.
▼TCS/DSC Indication/Indicator
Light (Turns on)
If the light stays on, the TCS, DSC or
the brake assist system may have a
malfunction and they may not operate
correctly. Take your vehicle to an
expert repairer (we recommend an
Authorised Mazda Repairer).
▼Air Bag/Seat Belt Pretensioner
System Warning Indication/
Warning Light
A system malfunction is indicated if the
warning light constantly
flashes,
constantly illuminates or does not
illuminate at all when the ignition is
switched ON. If any of these occur,
consult an expert repairer (we
recommend an Authorised Mazda
Repairer) as soon as possible. The
system may not operate in an accident.
WARNING
Never tamper with the air bag/
pretensioner systems and always have
an expert repairer (we recommend an
Authorised Mazda Repairer) perform
all servicing and repairs:
Self-servicing or tampering with the
systems is dangerous. An air bag/
pretensioner could accidentally
activate or become disabled causing
serious injury or death.
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
*Some models.7-55

▼KEY Warning Indication/Warning
Light (Red)
“Keyless Entry System Malfunc. Have
the Vehicle Inspected” is displayed
This message is displayed if the
advanced keyless entry & push button
start system has a problem.
Contact an expert repairer (we
recommend an Authorised Mazda
Repairer).
CAUTION
If the message is indicated, or the push
button start indicator light (amber)
flashes, the engine may not start. If the
engine cannot be started, try starting it
using the emergency operation for
starting the engine, and have the
vehicle inspected at an expert repairer
(we recommend an Authorised Mazda
Repairer) as soon as possible.
Refer to Emergency Operation for
Starting the Engine on page 4-9.
“Key Not Detected” is displayed
xIf the presence of the key cannot be
detected (dead battery, battery
malfunction, no key), it is displayed
when the driver attempts to start the
engine (push button start operation,
brake pedal depression).
xDisplayed when it is determined that
a key that was in the vehicle has
been removed from the vehicle. (Key
taken out warning. Other than
IG-OFF).
▼Security Indicator Light
If the security indicator light flashes
continuously while you are driving, do
not shut
off the engine. Go to an
expert repairer (we recommend an
Authorised Mazda Repairer) and have
it checked. If the engine is shut off
while the indicator light is
flashing , you
will not be able to restart it.
Make sure the key is within the
operational range for signal
transmission. Switch the ignition off,
and then restart the engine. If the
engine does not start after 3 or more
tries, contact an expert repairer (we
recommend an Authorised Mazda
Repairer).
NOTE
Because the electronic codes are reset
when the immobilizer system is
repaired, the keys are needed. Make
sure to bring all the keys to an
Authorised Mazda Repairer so that
they can be programmed.
▼AWD Warning Indication/
Warning Light*
“AWD Malfunction. Front Wheel
Drive Only. Have the Vehicle
Inspected” is displayed/When the
light is turned on
The indication is displayed/the light
turns on under the following
conditions. The system may have a
malfunction. Have the vehicle checked
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
7-56*Some models.