2019 MAZDA MODEL 2 air condition
[x] Cancel search: air conditionPage 348 of 759
¾Do not hit or apply strong force to the Forward Sensing Camera (FSC) or the area around
it. If the Forward Sensing Camera (FSC) is severely hit or if there are cracks or damage
caused by
flying gravel or debris in the area around it, stop using the following systems
and consult an expert repairer (we recommend an Authorised Mazda Repairer).
¾High Beam Control System (HBC)
¾Adaptive LED Headlights (ALH)
¾Lane Departure Warning System (LDWS)
¾Driver Attention Alert (DAA)
¾Lane-keep Assist System (LAS) & Lane Departure Warning System (LDWS)
¾Traffic Sign Recognition System (TSR)
¾Advanced Smart City Brake Support (Advanced SCBS)
¾Smart City Brake Support [Forward] (SCBS F)
¾Smart Brake Support (SBS)
¾The direction in which the Forward Sensing Camera (FSC) is pointed has been finely
adjusted. Do not change the installation position of the Forward Sensing Camera (FSC) or
remove it. Otherwise, it could result in damage or malfunction.
¾Always use tyres for all wheels that are of the
specified size, and the same manufacturer,
brand, and tread pattern. In addition, do not use tyres with significantly different wear
patterns on the same vehicle as the system may not operate normally.
¾The Forward Sensing Camera (FSC) includes a function for detecting a soiled windscreen
and informing the driver, however, depending on the conditions, it may not detect plastic
shopping bags, ice or snow on the windscreen. In such cases, the system cannot accurately
determine a vehicle ahead and may not be able to operate normally. Always drive carefully
and pay attention to the road ahead.
NOTE
xIn the following cases, the Forward Sensing Camera (FSC) cannot detect target objects
correctly, and each system may be unable to operate normally.
xThe height of the vehicle ahead is low.
xYou drive your vehicle at the same speed as the vehicle ahead.
xHeadlights are not turned on during the night or when going through a tunnel.
xIn the following cases, the Forward Sensing Camera (FSC) may not be able to detect
target objects correctly.
xUnder bad weather condition, such as rain, fog and snow.
xThe window washer is being used or the windscreen wipers are not used when it's
raining.
xIce, fog, snow, frost, rainfall, dirt, or foreign matter such as a plastic bag is stuck on the
windscreen.
xTrucks with low loading platforms and vehicles with an extremely low or high profile.
: K H Q ' U L Y L Q J
L $ & 7 , 9 6 ( 1 6 (
Page 350 of 759
xIf the Forward Sensing Camera (FSC) cannot operate normally due to backlight or fog,
the system functions related to the Forward Sensing Camera (FSC) are temporarily
stopped and the following warning lights turn on. However, this does not indicate a
malfunction.
xHigh Beam Control System (HBC) warning light (amber)
xAdaptive LED Headlights (ALH) warning light (amber)
xLane Departure Warning System (LDWS) warning light
xLane-keep Assist System (LAS) & Lane Departure Warning System (LDWS) warning
light
xSmart Brake Support/Smart City Brake Support (SBS/SCBS) warning light (amber)
xIf the Forward Sensing Camera (FSC) cannot operate normally due to high temperatures,
the system functions related to the Forward Sensing Camera (FSC) are temporarily
stopped and the following warning lights turn on. However, this does not indicate a
malfunction. Cool down the area around the Forward Sensing Camera (FSC) such as by
turning on the air conditioner.
xHigh Beam Control System (HBC) warning light (amber)
xAdaptive LED Headlights (ALH) warning light (amber)
xLane Departure Warning System (LDWS) warning light
xLane-keep Assist System (LAS) & Lane Departure Warning System (LDWS) warning
light
xSmart Brake Support/Smart City Brake Support (SBS/SCBS) warning light (amber)
xIf the Forward Sensing Camera (FSC) detects that the windscreen is dirty or foggy, the
system functions related to the Forward Sensing Camera (FSC) are temporarily stopped
and the following warning lights turn on. However, this does not indicate a problem.
Remove the dirt from the windscreen or press the defroster switch and defog the
windscreen.
xHigh Beam Control System (HBC) warning light (amber)
xAdaptive LED Headlights (ALH) warning light (amber)
xLane Departure Warning System (LDWS) warning light
xLane-keep Assist System (LAS) & Lane Departure Warning System (LDWS) warning
light
xSmart Brake Support/Smart City Brake Support (SBS/SCBS) warning light (amber)
xIf there are recognizable cracks or damage caused by flying gravel or debris on the
windscreen, always have the windscreen replaced. Consult an expert repairer (we
recommend an Authorised Mazda Repairer) for replacement.
: K H Q ' U L Y L Q J
L $ & 7 , 9 6 ( 1 6 (
Page 353 of 759
& $ 8 7 , 2 1
Heed the following precautions to assure correct operation of each system.
¾Do not adhere stickers (including transparent stickers) to the surface of the radiator grille
and front emblem in and around the radar sensor (front), and do not replace the radiator
grille and front emblem with any product that is not a genuine product designed for use
with the radar sensor (front).
¾The radar sensor (front) includes a function for detecting soiling of the radar sensor's front
surface and informing the driver, however, depending on the conditions, it may require
time to detect or it may not detect plastic shopping bags, ice or snow. If this occurs, the
system may not operate correctly, therefore always keep the radar sensor (front) clean.
¾Do not install a grille guard.
¾If the front part of the vehicle has been damaged in a vehicle accident, the position of the
radar sensor (front) may have moved. Stop the system immediately and always have the
vehicle inspected at an expert repairer (we recommend an Authorised Mazda Repairer).
¾Do not use the front bumper to push other vehicles or obstructions such as when pulling
out of a parking space. Otherwise, the radar sensor (front) could be hit and its position
deviated.
¾Do not remove, disassemble, or modify the radar sensor (front).
¾For repairs, replacement or paint work around the radar sensor (front), consult an expert
repairer (we recommend an Authorised Mazda Repairer).
¾Do not modify the suspension. If the suspension are
modified, the vehicle's posture could
change and the radar sensor (front) may not be able to correctly detect a vehicle ahead or
an obstruction.
: K H Q ' U L Y L Q J
L $ & 7 , 9 6 ( 1 6 (
Page 356 of 759
& $ 8 7 , 2 1
If the rear bumper receives a severe impact, the system may no longer operate normally. Stop
the system immediately and have the vehicle inspected at an Authorised Mazda Dealer.
NOTE
xThe detection ability of the radar sensors (rear) has limitations. In the following cases,
the detection ability may lower and the system may not operate normally.
xThe rear bumper near the radar sensors (rear) has become deformed.
xSnow, ice or mud adheres to the radar sensors (rear) on the rear bumper.
xUnder bad weather conditions such as rain, snow and fog.
xUnder the following conditions, the radar sensors (rear) cannot detect target objects or it
may be difficult to detect them.
xStationary objects on a road or a road side such as small, two-wheeled vehicles,
bicycles, pedestrians, animals, and shopping carts.
xVehicle shapes which do not reflect radar waves well such as empty trailers with a low
vehicle height and sports cars.
xVehicles are shipped with the direction of the radar sensors (rear) adjusted for each
vehicle to a loaded vehicle condition so that the radar sensors (rear) detect approaching
vehicles correctly. If the direction of the radar sensors (rear) has deviated for some
reason, have the vehicle inspected at an Authorised Mazda Dealer.
xFor repairs or replacement of the radar sensors (rear), or bumper repairs, paintwork, and
replacement near the radar sensors, consult an Authorised Mazda Dealer.
xTurn off the system while pulling a trailer or while an accessory such as a bicycle carrier
is installed to the rear of the vehicle. Otherwise, the radio waves emitted by the radar will
be blocked causing the system to not operate normally.
xThe radar sensors are regulated by the relevant radio wave laws of the country in which
the vehicle is driven. If the vehicle is driven abroad, authorization from the country in
which the vehicle is driven may be required.
: K H Q ' U L Y L Q J
L $ & 7 , 9 6 ( 1 6 (
Page 366 of 759
Please note that the TPMS is not a substitute for proper tyre maintenance, and it is the
driver's responsibility to maintain correct tyre pressure, even if under-inflation has not
reached the level to trigger illumination of the TPMS low tyre pressure telltale.
Your vehicle has also been equipped with a TPMS malfunction indicator to indicate when
the system is not operating properly.
The TPMS malfunction indicator is combined with the low tyre pressure telltale. When the
system detects a malfunction, the telltale will flash for approximately one minute and then
remain continuously illuminated. This sequence will continue upon subsequent vehicle
start-ups as long as the malfunction exists. When the malfunction indicator is illuminated,
the system may not be able to detect or signal low tyre pressure as intended. TPMS
malfunctions may occur for a variety of reasons, including the installation of replacement
or alternate tyres or wheels on the vehicle that prevent the TPMS from functioning properly.
Always check the TPMS malfunction telltale after replacing one or more tyres or wheels on
your vehicle to ensure that the replacement or alternate tyres and wheels allow the TPMS to
continue to function properly.
¾To avoid false readings, the system samples for a little while before indicating a problem. As
a result it will not instantaneously register a rapid tyre deflation or blow out.
NOTE
Because this system detects slight changes in tyre conditions, the timing of the warning may
be faster or slower in the following cases:
xThe size, manufacturer, or the type of tyres is different from the specification.
xThe size, manufacturer, or the type of a tyre is different from the others, or the level of tyre
wear is excessively different between them.
xA run-flat tyre, studless tyre, snow tyre, or tyre chains are used.
xAn emergency tyre is used (The tyre pressure monitoring system warning light may flash
and then continue illuminating).
xA tyre is repaired using the emergency flat tyre repair kit.
xThe tyre pressure is excessively higher than the specified pressure, or the tyre pressure is
suddenly lowered for some reason such as a tyre burst during driving.
xThe vehicle speed is lower than about 15 km/h (9.3 mph) (including when the vehicle is
stopped), or the drive period is shorter than 5 minutes.
xThe vehicle is driven on an extremely rough road or a slippery, icy road.
xHard steering and rapid acceleration/deceleration are repeated such as during aggressive
driving on a winding road.
xLoad on the vehicle is applied to a tyre such as by loading heavy luggage to one side of
the vehicle.
xSystem initialization has not been implemented with the specified tyre pressure.
: K H Q ' U L Y L Q J
7 \ U H 3 U H V V X U H 0 R Q L W R U L Q J 6 \ V W H P
Page 378 of 759
xUnder extremely hot or cold weather conditions.
xThe vehicle is driven on bumps, inclines, gravel, or grass covered roads.
xAnything which generates ultrasound is near the vehicle, such as another vehicle's
horn, the engine sound of a motorcycle, the air brake sound of a large-sized vehicle, or
another vehicle's sensors.
xThe vehicle is driven in heavy rain or in road conditions causing water-splash.
xA commercially-available wing pole or an aerial for a radio transmitter is installed to
the vehicle.
xThe vehicle is moving towards a tall or square curbstone.
xAn obstruction is too close to the sensor.
xObstructions under the bumper may not be detected. Obstructions that are lower than the
bumper or thin which may have been initially detected may no longer be detected as the
vehicle approaches more closely to the obstruction.
xThe following types of obstructions may not be detected:
xThin objects such as wire or rope
xThings which absorb sonic waves easily such as cotton or snow
xAngular shaped objects
xVery tall objects, and those which are wide at the top
xSmall, short objects
xAlways have the system inspected at an expert repairer (we recommend an Authorised
Mazda Repairer) if any shock is applied to the bumpers, even in a minor accident. If the
sensors are deviated, they cannot detect obstructions.
x(With front sensor and front corner sensor)
The system may have a malfunction if the beep does not operate or the indicator light
does not illuminate when the park assist sensors switch is turned on. Consult an expert
repairer (we recommend an Authorised Mazda Repairer).
x(Without front sensor and front corner sensor)
The system may have a malfunction if the beep does not operate. Consult an expert
repairer (we recommend an Authorised Mazda Repairer).
x(With front sensor and front corner sensor)
The system may have a malfunction if the beep sound which indicates a system
malfunction is heard and the indicator light flashes. Consult an expert repairer (we
recommend an Authorised Mazda Repairer).
xThe beeper which indicates a system malfunction may not be heard if the ambient
temperature is extremely cold, or mud, ice, or snow adheres to the sensor area. Remove
any foreign material from the sensor area.
: K H Q ' U L Y L Q J
3 D U N L Q J 6 H Q V R U 6 \ V W H P
Page 391 of 759
9 H Q W 2 S H U D W L R Q
▼ $ G M X V W L Q J W K H 9 H Q W V
' L U H F W L Q J D L U I O R Z
7 R D G M X V W W K H G L U H F W L R Q R I D L U I O R Z P R Y H
W K H D G M X V W P H Q W N Q R E
NOTE
xWhen using the air conditioner under
humid ambient temperature conditions,
the system may blow fog from the vents.
This is not a sign of trouble but a result
of humid air being suddenly cooled.
& H Q W U H Y H Q W V G U L Y H U D Q G 6 L G H Y H Q W V
$ L U Y H Q W R S H Q F O R V H
NOTE
The air vents can be fully opened and
closed by operating the knob.
Open
Close
Knob
$ L U I O R Z G L U H F W L R Q D G M X V W P H Q W
Knob
& H Q W U H Y H Q W V I U R Q W S D V V H Q J H U
$ L U Y H Q W R S H Q F O R V H
OpenClose
Knob
$ L U I O R Z G L U H F W L R Q D G M X V W P H Q W
Knob
, Q W H U L R U ) H D W X U H V
$ L U & R Q G L W L R Q L Q J 6 \ V W H P
Page 397 of 759
6 H W W K H I D Q F R Q W U R O G L D O W R W K H G H V L U H G V S H H G
7 X U Q R Q W K H D L U F R Q G L W L R Q H U E \ S U H V V L Q J
W K H $ & V Z L W F K
$ I W H U F R R O L Q J E H J L Q V D G M X V W W K H I D Q
F R Q W U R O G L D O D Q G W H P S H U D W X U H F R Q W U R O
G L D O D V Q H H G H G W R P D L Q W D L Q P D [ L P X P
F R P I R U W
& $ 8 7 , 2 1
If the air conditioner is used while driving
up long hills or in heavy traffic, monitor the
high engine coolant temperature warning
light to see if it is illuminated or flashing
(page 4-38).
The air conditioner may cause engine
overheating. If the warning light is
illuminated or flashing, turn the air
conditioner off (page 7-28).
NOTE
x(Type A)
When maximum cooling is desired, set
the temperature control dial to the
extreme cold position and set the air
intake selector to the recirculated air
position, then turn the fan control dial
fully clockwise.
x(Type C/Type D)
When maximum cooling is desired, set the
temperature control dial to the extreme cold
position and set the air intake selector to the
recirculated air position, then set the fan
control dial to position 4.
x(Type A/Type C)
If warmer air is desired at floor level, set the
mode selector dial to the
position and adjust
the temperature control dial to maintain
maximum comfort.
xThe air to the floor is warmer than air
to the face (except when the temperature
control dial is set at the extreme hot or
cold position).
▼ 9 H Q W L O D W L R Q
6 H W W K H P R G H V H O H F W R U G L D O W R W K H
S R V L W L R Q
7 \ S H $ 7 \ S H %
6 H W W K H D L U L Q W D N H V H O H F W R U W R W K H R X W V L G H
D L U S R V L W L R Q
7 \ S H & 7 \ S H '
6 H W W K H D L U L Q W D N H V H O H F W R U W R W K H
S R V L W L R Q
6 H W W K H W H P S H U D W X U H F R Q W U R O G L D O W R W K H
G H V L U H G S R V L W L R Q
6 H W W K H I D Q F R Q W U R O G L D O W R W K H G H V L U H G
V S H H G
▼ : L Q G V F U H H Q ' H I U R V W L Q J D Q G
' H I R J J L Q J
6 H W W K H P R G H V H O H F W R U G L D O W R W K H
S R V L W L R Q
7 \ S H & 7 \ S H '
6 H W W K H D L U L Q W D N H V H O H F W R U W R W K H
S R V L W L R Q
6 H W W K H W H P S H U D W X U H F R Q W U R O G L D O W R W K H
G H V L U H G S R V L W L R Q
6 H W W K H I D Q F R Q W U R O G L D O W R W K H G H V L U H G
V S H H G
7 \ S H $ 7 \ S H &
, I G H K X P L G L I L H G K H D W L Q J L V G H V L U H G W X U Q
R Q W K H D L U F R Q G L W L R Q H U
7 \ S H '
3 U H V V W K H $ & V Z L W F K W R W X U Q R Q W K H D L U
F R Q G L W L R Q H U
, Q W H U L R U ) H D W X U H V
$ L U & R Q G L W L R Q L Q J 6 \ V W H P