2019 INFINITI QX30 sport mode

WARNING
Do not allow children to play with the seat
belts. Most seating positions are equipped
with Automatic Locking Retractor (ALR)
mode seat belts. If the seat belt becomes
wrapped around a child’s neck with the
ALR mode activated, the child can be seri-
ously injured or killed if the seat belt re-
tracts and becomes tight. This can occur
even if the vehicle is parked. Unbuckle the
seat belt to release the child. If the seat belt
can not be unbuckled or is already unbuck-
led, release the child by cutting the seat
belt with a suitable tool (such as a knife or
scissors) to release the seat belt.
Children need adults to help protect them.
They need to be properly restrained.
In addition to the general information in this
manual, child safety information is available
from many other sources, including doctors,
teachers, government traffic safety offices,
and community organizations. Every child is
different, so be sure to learn the best way to
transport your child.There are three basic types of child restraint
systems:•Rear-facing child restraint
•Forward-facing child restraint
•Booster seat
The proper restraint depends on the child’s
size. Generally, infants up to about 1 year and
less than 20 lb (9 kg) should be placed in
rear-facing child restraints. Forward-facing
child restraints are available for children who
outgrow rear-facing child restraints and are
at least 1 year old. Booster seats are used to
help position a vehicle lap/ shoulder belt on a
child who can no longer use a forward-facing
child restraint.
WARNING
Infants and children need special protec-
tion. The vehicle’s seat belts may not fit
them properly. The shoulder belt may come
too close to the face or neck. The lap belt
may not fit over their small hip bones. In an
accident, an improperly fitting seat belt
could cause serious or fatal injury. Always
use appropriate child restraints.
All U.S. states and Canadian provinces or
territories require the use of approved childrestraints for infants and small children. See
"Child restraints" for more information.
A child restraint may be secured in the vehicle
by using either the LATCH (Lower Anchor
and Tethers for CHildren) system or with the
vehicle seat belt. For additional information,
refer to "Child restraints".
INFINITI recommends that all pre-teens and
children be restrained in the rear seat. Stud-
ies show that children are safer when prop-
erly restrained in the rear seat than in the
front seat.
This is especially important because your
vehicle has a supplemental restraint system
(air bag system) for the front passenger. (See
"Supplemental Restraint System (SRS)"
later in this section.)
INFANTS
Infants up to at least 1 year old should be
placed in a rear-facing child restraint.
INFINITI recommends that infants be placed
in child restraints that comply with Federal
Motor Vehicle Safety Standards or Canadian
Motor Vehicle Safety Standards. You should
choose a child restraint which fits your ve-
hicle and always follow the manufacturer’s
instructions for installation and use.
CHILD SAFETY
Safety — seats, seat belts and supplemental restraint system1-17

Drive mode switch
The drive mode switch allows you to choose
between drive programs with different driv-
ing characteristics.
Press drive mode switch
1. A popup2will
be displayed in the vehicle information dis-
play showing the current selection. After
around 2 seconds, the selected drive program
appears in the lower frame of the vehicle
information display
3and the popup will
disappear.The automatic transmission switches to drive
program E each time the engine is started.
E (Economy): comfortable, economical driv-
ing
S (Sport): sporty driving style
M (Manual): manual gear shifting
For more details of the manual drive program
see "Manual drive program" later in this sec-
tion.
NSD587NSD726
NSD725
5-22Starting and driving

1Tire size (example: P215/60R16 94H)
1 P: The “P” indicates the tire is designed for
passenger vehicles. (Not all tires have this
information.)
2 Three-digit number (215): This number
gives the width in millimeters of the tire
from sidewall edge to sidewall edge.
3 Two-digit number (60): This number,
known as the aspect ratio, gives the tire’s
ratio of height to width.
4 R: The “R” stands for radial.
5 Two-digit number (16): This number is the
wheel or rim diameter in inches.
6
Two- or three-digit number (94): This num-
ber is the tire’s load index. It is a measurement
of how much weight each tire can support.
You may not find this information on all tires
because it is not required by law.
7H:Tire speed rating. You should not drive the
vehicle faster than the tire speed rating.
2TIN (Tire Identification Number) for a new
tire (example: DOT XX XX XXX XXXX)
1 DOT: Abbreviation for the “Department of
Transportation”. The symbol can be placed
above, below or to the left or right of the
Tire Identification Number.
2 Two-digit code: Manufacturer’s identifi-
cation mark
3 Two-digit code: Tire size
4 Three-digit code: Tire type code (Optional)
5 Four numbers represent the week and
year the tire was built. For example, the
numbers 3103 means the 31st week of
2003. If these numbers are missing, then
look on the other sidewall of the tire.
3Tire ply composition and material
The number of layers or plies of rubber-
coated fabric in the tire. Tire manufactur-
ers also must indicate the materials in thetire, which include steel, nylon, polyester,
and others.
4Maximum permissible inflation pressure
This number is the greatest amount of air
pressure that should be put in the tire. Do
not exceed the maximum permissible in-
flation pressure.
5Maximum load rating
This number indicates the maximum load
in kilograms and pounds that can be car-
ried by the tire. When replacing the tires
on the vehicle, always use a tire that has
the same load rating as the factory in-
stalled tire.
6Term of “tubeless” or “tube type”
Indicates whether the tire requires an in-
ner tube (“tube type”) or not (“tubeless”).
7The word “radial”
The word “radial” is shown, if the tire has
radial structure.
8Manufacturer or brand name”
Manufacturer or brand name is shown.
Other tire-related terminology:
In addition to the many terms that are de-
fined throughout this section, Intended Out-
board Sidewall is (1) the sidewall that con-
tains a whitewall, bears white lettering or
bears manufacturer, brand and/or model
SDI1606Z
Example
NDI1623
Example
Do-it-yourself8-31

GT and Sport models:
Item Offset in (mm) Size
Road wheel 1.50 (38) 6.5J x 17
1.81 (46) 7.0J x 18
1.71 (43.5) 8.0J x 19
Tire size 215/60 R17 96V
235/50 R18 97V*
235/50 R18 97H* **
235/45 R19 95V*
* : Use of snow chains NOT permitted.
**: US only.
All Road models:
Item Offset in (mm) Size
Road wheel 1.61 (41) 6.5J x 17
(steel)
1.61 (41) 7.0J x 18
(alloy)
Tire size 215/60 R17 96V
235/50 R18 97V*
235/50 R18 97H* **
* : Use of snow chains NOT permitted.
**: US only.
Dimension Model in (mm)
Overall length 174.2 (4425)
Overall width (incl. mirrors) 82.0 (2083)
Overall height GT without roof rails 58.9 (1495)
GT with roof rails 59.5 (1510)
Sport without roof rails 58.1 (1475)
Sport with roof rails 58.7 (1490)
Allroad without roof rails 58.7 (1515)
Allroad with roof rails 61.2 (1530)
Front track GT 17” wheels 61.9 (1572)
GT 18” wheels 61.3 (1556)
GT 19” wheels 61.5 (1561)
Sport 17” wheels 62 (1574)
Sport 19” wheels 61.5 (1563)
Allroad 17” wheels 61.7 (1566)
Allroad 18” wheels 61.5 (1561)
Rear track GT 17” wheels 61.9 (1573)
GT 18” wheels 61.2 (1555)
GT 19” wheels 61.7 (1566)
Sport 17” wheels 62.2 (1580)
Sport 19” wheels 61.7 (1567)
Allroad 17” wheels 62.0 (1574)
Allroad 18” wheels 61.7 (1566)
Wheelbase 106.3 (2700)
WHEELS AND TIRES DIMENSIONS
10-8Technical information