Page 30 of 699

28
Quick Reference Guide
What to Do If
*1:Canadian models and 2.0 L engine models
The ignition switch does 
not turn from 
(0 to (q. 
Why?
The power mode does not 
change from VEHICLE OFF 
(LOCK) to ACCESSORY. 
Why?
The steering wheel may be locked.
●Try to turn the steering wheel left and right 
while turning the ignition key.
●Move the steering wheel left and right after 
pressing the  ENGINE START/STOP  button.
The ignition switch does 
not turn from 
(q to (0 and 
I cannot remove the key. 
Why?
The power mode does not 
change from ACCESSORY 
to VEHICLE OFF (LOCK). 
Why?
The shift lever should be moved to (P.
Why does the brake pedal 
pulsate slightly when 
applying the brakes?This can occur when the ABS activates and does not indicate a 
problem. Apply firm, steady pressure on the brake pedal. Never 
pump the brake pedal.
2 Anti-lock Brake System (ABS)  (P535)
Models without smart entry system
Models with smart entry system*1
Models without smart entry system
Models with smart entry system*1
Models without smart entry system
Models with smart entry system
19 CIVIC 5D HUM (KA KC KL)-31TGG6201.book  28 ページ  2018年10月25日 木曜日 午後4時12分 
         
        
        
     
        
        Page 31 of 699

29
Quick Reference Guide
The rear door cannot be 
opened from inside the 
vehicle. Why?Check if the childproof lock is in the 
lock position. If so, open the rear 
door with the outside door handle.
To cancel this function, slide the lever 
up to the unlock position.
Why do the doors lock 
after I unlocked the doors?If you do not open the doors within 30 seconds, the doors are 
relocked automatically for security.
Why does the beeper 
sound when I open the 
driver's door?The beeper sounds when:
●The key is left in the ignition switch*.
●The power mode* is in ACCESSORY.
●The exterior lights are left on.
Why does a beeper sound 
when I walk away from the 
vehicle after I close the 
door?
The beeper sounds if you move outside the walk away auto lock 
operating range before the  door completely closes.
2Locking the doors and hatch (Walk away auto lock ®)  (P148)
Models with smart entry system
* Not available on all models
19 CIVIC 5D HUM (KA KC KL)-31TGG6201.book  29 ページ  2018年10月25日 木曜日 午後4時12分 
         
        
        
     
        
        Page 66 of 699

uuChild Safety uSafety of Infants and Small Children
64
Safe DrivingMost child seats are LATCH-compatible (L ower Anchors and Tethers for CHildren). 
Some have a rigid-type conn ector while others have a flexible-type connector. Both 
are equally easy to use. Some existing and  previously owned child seats can only be 
installed using the seat belt. Whichever type you choose, follow the child seat 
manufacturer’s use and care  instructions including recommended expiration dates 
as well as the instructions in this manual. Proper installation is key to maximizing 
your child’s safety.
In seating positions and vehicles not equipped with LATCH, a LATCH-compatible 
child seat can be installed using the seat belt and a top tether for added security. 
This is because all child seats are required to  be designed so that they can be secured 
with a lap belt or the lap part of a lap/sh oulder belt. In addition, the child seat 
manufacturer may advise that a seat belt be used to attach a LATCH-compatible seat 
once a child reaches a specified weight.  Please read the child seat owner’s manual 
for proper installation instructions.
■Important consideration wh en selecting a child seat
Make sure the child seat meets th e following three requirements:
• The child seat is the correct  type and size for the child.
• The child seat is the correct  type for the seating position.
• The child seat is compliant with Federa l Motor Vehicle Safety Standard 213 or 
Canadian Motor Vehicle Safety Standard 213.
■Selecting a Child Seat1 Selecting a Child Seat
Installation of a LATCH-compatible child seat is 
simple.
LATCH-compatible child s eats have been developed 
to simplify the installati on process and reduce the 
likelihood of injuries caused  by incorrect installation.
19 CIVIC 5D HUM (KA KC KL)-31TGG6201.book  64 ページ  2018年10月25日 木曜日 午後4時12分 
         
        
        
     
        
        Page 91 of 699

89
uuIndicators u
Continued
Instrument Panel
IndicatorNameOn/BlinkingExplanationMessage
System Message 
Indicator*
●Comes on along with a beep 
when a problem is detected. A 
system message on the driver 
information interface appears at 
the same time.●While the indicator is on, press the   
(display/information) button to see the 
message again.
●Refer to the Indicators  information in this 
chapter when a system message appears 
on the driver information interface. Take 
the appropriate action for the message.
●The driver information interface does not 
return to the normal screen unless the 
warning is canceled, or the   button 
is pressed.
—
Turn Signal and 
Hazard Warning 
Indicators
●Blinks when you operate the turn 
signal lever.
●Blink along with all turn signals 
when you press the hazard 
warning button.
●Does not blink or blinks rapidly
2 Replacing Light Bulbs  P. 586, 590 
—
High Beam 
Indicator●Comes on when the high beam 
headlights are on.——
Lights On 
Indicator
●Comes on when the light switch 
in a position other than  OFF or 
when the switch is set to  AUTO 
and the exterior lights come on.●If you remove the key from the ignition 
switch*1 while the exterior lights are on, a 
chime sounds when the driver's door is 
opened.—
* Not available on all models
19 CIVIC 5D HUM (KA KC KL)-31TGG6201.book  89 ページ  2018年10月25日 木曜日 午後4時12分 
         
        
        
     
        
        Page 93 of 699
91
uuIndicators u
Continued
Instrument Panel
*1:Models with the smart entry system have an  ENGINE START/STOP button instead of an ignition switch.
*2:Canadian models only: Apply and hold the  brake pedal before turning the ignition on.
IndicatorNameOn/BlinkingExplanationMessage*2
Immobilizer 
System Indicator
●Blinks if the immobilizer system 
cannot recognize the key 
information.●Blinks - You cannot start the engine. Turn 
the ignition switch to LOCK 
(0*1, pull the 
key out*2, and then insert the key and turn 
it to ON 
(w*1 again.●Repeatedly blinks  - The system may be 
malfunctioning. Have your vehicle 
checked by a dealer.
●Do not attempt to alter this system or add 
other devices to it. Electrical problems can 
occur.
Indicator
Models without 
smart entry system
Models with smart 
entry system
19 CIVIC 5D HUM (KA KC KL)-31TGG6201.book  91 ページ  2018年10月25日 木曜日 午後4時12分 
         
        
        
     
        
        Page 107 of 699
105
uuIndicators uDriver Information Interface Wa rning and Information Messages
Continued
Instrument Panel
MessageConditionExplanation
●Appears when the electric parking brake switch is 
pressed without depressing the brake pedal while 
the electric parking brake is in operation.●Appears while driving  - Press the electric parking 
brake switch with the brake pedal depressed.
2 Parking Brake  P. 528
MessageConditionExplanation
●Appears when you open the driver’s door while the 
ignition key is in ACCESSORY 
(q.
●Turn the ignition switch to LOCK (0, then remove the 
key.
●Appears when you open the driver’s door while the 
ignition key is in LOCK 
(0.
●Remove the key from  the ignition switch.
●Appears when the ignition key is turned to 
ACCESSORY 
(q from ON (w. (The driver’s door is 
closed.)—
Continuously 
variable transmission 
models
Manual transmission 
models
Models without smart entry system
19 CIVIC 5D HUM (KA KC KL)-31TGG6201.book  105 ページ  2018年10月25日 木曜日 午後4時12分 
         
        
        
     
        
        Page 110 of 699

108
uuIndicators uDriver Information Interface Wa rning and Information Messages
Instrument Panel
MessageConditionExplanation
●Appears if the smart entry remote battery is too 
weak to start the engine or the key is not within 
operating range to start the engine.
A beeper sounds six times.●Bring the back of the smart entry remote into contact 
with the ENGINE START/STOP  button.
2If the Smart Entry Remote Battery is Weak  P. 647
●Appears when the starter system has a problem.●As a temporary measure, press and hold the ENGINE 
START/STOP  button for up to 15 seconds while pressing 
the brake pedal and clutch  pedal (manual transmission 
only), manually start the engine.
Have your vehicle checked by a dealer.
●Appears as soon as a problem is detected in the 
smart entry system or pus h button starting system.●Appears constantly - Have your vehicle checked by a 
dealer.
U.S.
*
Canada
* Not available on all models
19 CIVIC 5D HUM (KA KC KL)-31TGG6201.book  108 ページ  2018年10月25日 木曜日 午後4時12分 
         
        
        
     
        
        Page 133 of 699
131
uuGauges and Driver Information Interface uDriver Information Interface
Continued
Instrument PanelENTERKeyless Access Light Flash
Keyless Access Beep
3
4Keyless Access Setup*
3
4
Door Unlock Mode
* Not available on all models
19 CIVIC 5D HUM (KA KC KL)-31TGG6201.book  131 ページ  2018年10月25日 木曜日 午後4時12分