2019 HONDA ACCORD HYBRID start stop button

465Continued
Driving
When DrivingStarting the Engine 1. Make sure the parkin g brake is applied.
u The parking brake indicator (red) comes
on for 30 seconds when you pull up the
electric parking brake switch.
u The parking brake must be applied to
start the engine.
2. Depress the brake pedal.
u Although it is possible to start the vehicle
in ( N
with the parking brake applied, it is
safer to start it in ( P
.
3. Press the ENGINE START/STOP button
without depressing the accelerator pedal. 1 Starting the Engine
Keep your foot firmly on the brake pedal when
starting the engine.
The engine is harder to st art in cold weather and in
thinner air found at altitudes above 8,000 feet (2,400
meters).
When starting the engine in cold weather, turn off all
electrical accessories such as the lights, climate
control system and rear de fogger in order to reduce
battery drain.
If you live in a region where winter is extremely cold,
an engine block heater will improve starting and
warming of the engine. Cons ult a dealer for details.
If the exhaust system sounds abnormal or you can
smell exhaust gas inside the vehicle, have your vehicle
checked by a dealer. There may be a problem with
the engine or exhaust system.
The immobilizer system pr otects your vehicle from
theft.
If an improperly c oded device is used, the engine’s
fuel system is disabled.
2 Immobilizer System P. 183Automatic transmission models
Electric Parking Brake Switch
Brake Pedal

uu When Driving u Starting the Engine
466
Driving 1. Make sure the parking brake is applied.
u The parking brake indicator (red) comes
on for 30 seconds when you pull up the
electric parking brake switch.
u The parking brake must be applied to
start the engine.
2. Check that the tr ansmission is in ( P
, then
depress the brake pedal.
u Although it is possible to start the vehicle
in ( N
with the parking brake applied, it is
safer to start it in ( P
.
3. Press the ENGINE START/STOP button
without depressing the accelerator pedal.Continuously variable transmission models
Electric Parking Brake Switch 1 Starting the Engine
Bring the remote close to the ENGINE START/STOP
button if the battery in the remote is weak.
2 If the Remote Battery is Weak P. 672
The engine may not start if the remote is subjected to
strong radio waves.
Do not hold the ENGINE START/STOP button to
start the engine.
If the engine does not start, wait at least 30 seconds
before trying again.
Brake Pedal

Continued
467uu When Driving u Starting the Engine
Driving
1. Make sure the parkin g brake is applied.
u The parking brake indicator (red) comes
on for 30 seconds when you pull up the
electric parking brake switch.
u The parking brake must be applied to
start the engine.
2. Check that the transmission is in neutral.
Then depress the brake pedal with your
right foot, and the clutch pedal with your
left foot.
u The clutch pedal must be fully depressed
to start the engine.
3. Press the ENGINE START/STOP button
without depressing the accelerator pedal. 1 Starting the Engine
If the vehicle stalls on a slope, the electric parking
brake system may automatica lly engage. If it does
not, engage it manually, th en start the engine again.Manual transmission models
Manual transmission models
Electric Parking Brake Switch
Brake PedalClutch Pedal

468 uu When Driving u Starting the Engine
Driving You can turn the engine off when the vehicle is completely stopped.
1. Put the transmission into ( P
.
2. Press the ENGINE START/STOP button.
• If the transmission is in neutral, press the ENGINE START/STOP button.
• If the transmission is in any gear other than neutral, depress the clutch pedal, then
press the ENGINE START/STOP button.■ Stopping the Engine Automatic transmission/Continuousl y variable transmission models
Manual transmission models

Continued
469uu When Driving u Starting the Engine
Driving
You can remotely start the engine using the button on the remote.
■ To start the engine
When started remotely, the engine automati cally shuts off after 10 minutes of idling
and/or the brake pedal and ENGINE START/STOP button have not been pressed
simultaneously.
To extend the run time for another 10 mi nutes during the first run, press the
button, then press an d hold the button.
u Some exterior lights flash six times if a 10-minute extension request was
transmitted successfully.■ Remote Engine Start with Vehicle Feedback * 1 Remote Engine Start with Vehicle Feedback *
The remote engine start may violate local laws.
Before using the remote e ngine start, check your
local laws.
If there are buildings an d obstacles between your
vehicle and the remote, th e range will be reduced.
The range may be less when the vehicle is running.
This distance may vary by external electrical
interference.
The engine may not start by the remote engine start
if:
• You have disabled a remo te engine start setting
using the audio/information screen.
• The power mode is not in VEHICLE OFF.
• The transmission is in a position other than ( P
.
• The hood is open, or any door or the trunk is
unlocked.3
WARNING Engine exhaust contains toxic carbon
monoxide.
Breathing carbon monoxide can kill you or
cause unconsciousness.
Never use the remote engine starter when
the vehicle is parked in a garage or other
area with limited ventilation.Press the button, th en press and hold
the button.
Some exterior lights flash once. Go within the range,
and try again.
LED: Blinks when any button is pressed.
Some exterior lights flash six
times if the engine runs
successfully. Some exterior lights will not
flash if the engine runs
unsuccessfully.
* Not available on all models

uu When Driving u Starting the Engine
470
Driving ■ To stop the engine 1 Remote Engine Start with Vehicle Feedback *
• You have already used the remote twice to start
the engine.
• Another registered remo te is in the vehicle.
• There is an antenna failure.
• The door is unlocked with the built-in key.
• The engine oil pressure is low.
• The engine coolant temper ature is extremely high.
• The security system alarm is not set.
The engine may stop whil e it is running if:
• You do not start the vehicl e within 10 minutes of
starting the engine with the remote.
• The engine is stopped by using the remote.
• The security system alarm is activated.
• The door is unlocked with the built-in key.
• The hood is open.
• The engine coolant temper ature is extremely high.
• The battery is low.
• The engine oil pressure is low.
• The malfunction indicator lamp (MIL) comes on if
there is a problem with the emissions control
systems.
• You press the ENGINE START/STOP button
without depressing the brake pedal.
• The transmission is in a position other than ( P
.
• You press the shift lever release button. Automatic transmission models
Continuously variable transmission modelsPress and hold the
button for one second. Go within the range,
and try again.
The exterior lights flash once if the engine stops successfully.The exterior lights will not flash when the remote is out of
the smart entry system range.
The engine will not stop.
* Not available on all models

uu When Driving u Starting the Engine
472
Driving 1. While depressing the brake pedal, press the ENGINE START/STOP button.
2. Keeping your right foot on the brake pedal, put the transmission into ( D
. Select
( R
when reversing.
3. With the parking brake applied, release the brake pedal and gently depress the
accelerator pedal.
u Make sure the parking brake indicator (red) goes off.
■ Hill start assist system
Hill start assist keeps the brake engaged br iefly to help prevent the vehicle from
rolling on inclines as you move your fo ot from the brake pedal to the accelerator.
Put the transmission into ( D
, ( S *
or ( L *
when facing uphill, or ( R
when facing
downhill, then release the brake pedal.
Depress the clutch pedal, a nd put the transmission into ( 1
when facing uphill, or ( R

when facing downhill, then release the brake pedal.■ Starting to Drive Automatic transmission/Continuousl y variable transmission models
1 Starting to Drive
The engine stops when th e transmission is taken out
of ( P
before the ENGINE START/STOP button is
pressed. Follow the step 1 when starting to drive.
You can also release the parking brake by pressing
the electric parking brake sw itch while depressing the
brake pedal.
When facing downhill, you can start your vehicle
more smoothly by manually releasing it with the
electric parking brake switch than by releasing it with
the accelerator pedal. When the engine was started using the button on the
remote
When the engine was started using the button on the remote
When the engine was started in any case
1 Hill start assist system
Hill start assist may not prevent the vehicle from
rolling downhill on a very st eep or slippe ry slope, and
does not operate on small inclines.
Hill start assist is not a replacement for the parking
brake.
Hill start assist will operate even when VSA ® is
switched off.Automatic transmission/Continuousl y variable transmission models
Manual transmission models
* Not available on all models

uu When Driving u Shifting
478
Driving ■ If you want to keep the transmi ssion in ( N
position [car wash mode]
With the engine running:
1. Press and hold the brake pedal.
2. Press and release the ( N
button.
u ( N
(Neutral) hold mode will appear on the driver information interface.
3. Press the ( N
button again and hold it for two seconds.
u The vehicle will enter car wash mode, wh ich must be used when your vehicle
is pulled through a conveyor type automatic car wash where you or an
attendant do not remain in the vehicle.
If the ENGINE STOP/START button is pressed
after car wash mode has been activated, the
power mode will change to ACCESSORY and
a message will be displayed on the driver
information interface.
u For 15 minutes the transmission remains
in ( N
with the power mode will remain
in ACCESSORY. After that, the
transmission automatically changes to
( P
and the power mode changes to OFF.
u Manually changing to ( P
cancels
ACCESSORY mode. The ( P
indicator
comes on and the power mode changes
to OFF. You must always put the
transmission into ( P
when car wash
mode is no longer needed. 1 If you want to keep the transmission in ( N
position [car wash
mode] NOTICE
When transmission is too hot, carwash mode may
not be available. Let the engine idle and cool down
transmission.
To keep the vehicle in ( N
position, you can also
follow this procedure:
While the power mode is on, select ( N
, and then
within five seconds, press the ENGINE STOP/START
button.
Note that the transmiss ion may not stay in ( N

position while any of the following indicators is on:
• Transmission system indicator.
• Malfunction indicator lamp.
• Charging system indicator.