2018 YAMAHA YZF-R6 lock

Periodic maintenance an d a djustment
7-25
7
EAU36505
Brake li ght switches
The brake light should come on just
before braking takes effect. The brake
light is activated by switches connect-
ed to the brake lever and brake pedal.
Since the brake light switches are
components of the anti-lock brake sys-
tem, they should only be serviced by a
Yamaha dealer.
EAU22393
Checkin g the front an d rear
b rake pa ds
The front and rear brake pads must be
checked for wear at the intervals spec-
ified in the periodic maintenance and
lubrication chart.
EAU36891Front brake pa ds
Each front brake pad is provided with
wear indicators, which allows you to
check the brake pad wear without hav-
ing to disassemble the brake. To check
the brake pad wear, check the position
of the wear indicators while applying
the brake. If a brake pad has worn to
the point that a wear indicator almost
touches the brake disc, have a
Yamaha dealer replace the brake pads as a set.
1. Brake pad wear indicator
11
UBN6E1E0.book Page 25 Thursday, October 5, 2017 2:48 PM

Periodic maintenance an d a djustment
7-27
7 
Clean the filler cap before re-
movin g. Use only DOT 4 b rake
flui d from a seale d container.
 Use only the specifie d b rake flu-
i d ; otherwise, the ru bber seals
may deteriorate, causin g leak-
a g e.
 Refill with the same type of
brake flui d. A ddin g a b rake flui d
other than DOT 4 may result in a
harmful chemical reaction.
 Be careful that water or dust
d oes not enter the brake flui d
reservoir when refillin g. Water
will si gnificantly lower the boil-
in g point of the flui d an d may re-
sult in vapor lock, an d d irt may
clo g the ABS hy draulic unit
valves.NOTICE
ECA17641
Brake flui d may damag e painte d
surfaces or plastic parts. Always
clean up spille d flui d imme diately.
As the brake pads wear, it is normal for
the brake fluid level to gradually go
down. A low brake fluid level may indi-
cate worn brake pads and/or brake
system leakage; therefore, be sure to
check the brake pads for wear and the
brake system for leakage. If the brake
fluid level goes down suddenly, have a
Yamaha dealer check the cause before further riding.
EAU22734
Chan gin g the brake flui d
Have a Yamaha dealer change the
brake fluid every 2 years. In addition,
have the seals of the master cylinders
and brake calipers, as well as the brake
hoses replaced at the intervals listed
below or sooner if they are damaged or
leaking.
 Brake seals: every 2 years
 Brake hoses: every 4 years
UBN6E1E0.book Page 27 Thursday, October 5, 2017 2:48 PM

Periodic maintenance an d a djustment
7-28
7
EAU22762
Drive chain slack
The drive chain slack should be
checked before each ride and adjusted
if necessary.
EAU74251To check the drive chain slack
1. Place the motorcycle on the side- stand.
TIP
When checking and adjusting the drive
chain slack, there should be no weight
on the motorcycle.
2. Shift the transmission into theneutral position.
3. Measure the drive chain slack as shown.
4. If the drive chain slack is incorrect, adjust it as follows. NOTICE: Im-
proper drive chain slack will
overloa d the en gine as well as
other vital parts of the motorcy-
cle an d can lead to chain slip-
pa ge or b reakag e. To prevent
this from occurrin g, keep the
d rive chain slack within the
specified limits.
[ECA10572] EAU74260
To a
djust the drive chain slack
Consult a Yamaha dealer before ad-
justing the drive chain slack. 1. Loosen the axle nut and the lock- nut on each side of the swingarm.
2. To tighten the drive chain, turn the drive chain slack adjusting bolt on
each side of the swingarm in di-
rection (a). To loosen the drive
chain, turn the adjusting bolt on
each side of the swingarm in di-
rection (b), and then push the rear
wheel forward.
1. Drive chain slack
Drive chain slack:30.0–45.0 mm (1.18–1.77 in)
1
1. Drive chain puller
2. Axle nut
3. Drive chain slack adjusting bolt
4. Locknut
5. Alignment marks
1. Drive chain slack adjusting bolt
2. Locknut
4
23
1
5
12
(a)
(b)
UBN6E1E0.book Page 28 Thursday, October 5, 2017 2:48 PM

Periodic maintenance an d a djustment
7-29
7
TIP
Using the alignment marks on each
side of the swingarm, make sure that
both drive chain pullers are in the same
position for proper wheel alignment.
3. Tighten the axle nut, then the lock-
nuts to their specified torques.
4. Make sure that the drive chain pullers are in the same position,
the drive chain slack is correct,
and the drive chain moves
smoothly.
EAU23026
Cleanin g an d lu bricatin g the
d rive chain
The drive chain must be cleaned and
lubricated at the intervals specified in
the periodic maintenance and lubrica-
tion chart, otherwise it will quickly wear
out, especially when riding in dusty or
wet areas. Service the drive chain as
follows.
NOTICE
ECA10584
The drive chain must be lu bricate d
after washin g the motorcycle, ri din g
in the rain or ri din g in wet areas.
1. Clean the drive chain with kero-
sene and a small soft brush.
NOTICE: To prevent d amaging
the O-rin gs, do not clean the
d rive chain with steam cleaners,
hi gh-pressure washers or inap-
propriate solvents.
[ECA11122]
2. Wipe the drive chain dry.
3. Thoroughly lubricate the drive chain with a special O-ring chain
lubricant. NOTICE: Do not use
en gine oil or any other lu bri-
cants for the drive chain, as they
may contain su bstances that
coul d damag e the O-rin gs.
[ECA11112]
Ti ghtenin g torques:
Axle nut: 110 N·m (11 kgf·m, 81 lb·ft)
Locknut: 16 N·m (1.6 kgf·m, 12 lb·ft)
UBN6E1E0.book Page 29 Thursday, October 5, 2017 2:48 PM

Periodic maintenance an d a djustment
7-36
7
EAU2370A
Replacin g the fuses
The main fuse, the ABS motor fuse,
and fuse box 1 are located under the
rider seat. (See page 4-23.)
TIP
To access the ABS motor fuse, remove
the starter relay cover by pulling it up-
ward.
Fuse box 2 is located under panel A.
(See page 7-7.)
If a fuse is blown, replace it as follows.
1. Turn the key to “OFF” and turn off the electrical circuit in question.
2. Remove the blown fuse, and then install a new fuse of the specified
amperage. WARNING! Do not
use a fuse of a hi gher ampera ge
ratin g than recommen ded to
avoi d causin g extensive dam-
a g e to the electrical system an d
possi bly a fire.
[EWA15132]
1. ABS motor fuse
2. Starter relay cover
3. ABS motor spare fuse
4. Main fuse
1. Fuse box 1
2. Fuel injection system fuse
3. ABS ECU fuse
4. Terminal fuse 1 (for optional equipment)
5. Electronic throttle valve fuse
6. Backup fuse (for clock and immobilizer sys-
tem)
7. ABS solenoid fuse
8. Spare fuse
2
3
4
1
2
1
3
4
5
8
6
7
1. Fuse box 2
2. Hazard fuse
3. Headlight fuse
4. Ignition fuse
5. Signaling system fuse
6. Right radiator fan motor fuse
7. Left radiator fan motor fuse
8. Spare fuse
2
1
3
4
5
8
6
7
UBN6E1E0.book Page 36 Thursday, October 5, 2017 2:48 PM

Periodic maintenance an d a djustment
7-41
7 En
gine overheatin g
WARNING
EWAT1041
Do not remove the ra diator cap when the en gine an d ra diator are hot.
Scal din g hot flui d an d steam may b e blown out un der pressure, which
coul d cause serious injury. Be sure to wait until the eng ine has cooled.
 Place a thick ra g, like a towel, over the ra diator cap, an d then slowly ro-
tate the cap counterclockwise to the detent to allow any resi dual pres-
sure to escape. When the hissin g soun d has stopped , press down on the
cap while turnin g it counterclockwise, an d then remove the cap.
TIP
If coolant is not available, tap water can be temporarily used instead, provided
that it is changed to the recommended coolant as soon as possible.
Wait until the engine
has cooled.
Check the coolant
level in the reservoir
and radiator.Add coolant.
(See TIP.)
The coolant level is
OK.
There is no leakage.
There is leakage.
The coolant level is
low.
Check the cooling
system for leakage.
Have a Yamaha
dealer check and
repair the cooling
system.
Start the engine. If the engine overheats again,
have a Yamaha dealer check and repair the cooling
system.
UBN6E1E0.book Page 41 Thursday, October 5, 2017 2:48 PM

11-1
11
Index
A
ABS ....................................................... 4-19
ABS warning light ................................... 4-7
Air filter element .................................... 7-18
Auxiliary DC connector ......................... 4-30
B
Battery .................................................. 7-34
Brake and clutch levers, checking
and lubricating .................................... 7-31
Brake and shift pedals, checking and lubricating .................................... 7-31
Brake fluid, changing ............................ 7-27
Brake fluid level, checking .................... 7-26
Brake lever ............................................ 4-18
Brake lever free play, checking............. 7-24
Brake light switches.............................. 7-25
Brake pedal........................................... 4-18
C
Cables, checking and lubricating ......... 7-30
Canister................................................. 7-12
Care ........................................................ 8-1
Catalytic converters .............................. 4-22
Clutch lever ........................................... 4-17
Clutch lever free play, adjusting ........... 7-23
Coolant ................................................. 7-17
Coolant temperature warning light ......... 4-6
Cowlings and panels, removing and installing................................................ 7-7
D
Data recording, vehicle ......................... 10-3
Diagnostic connector............................ 10-2
Dimmer switch ........................................ 4-4
D-mode (drive mode) .............................. 3-1
Drive chain, cleaning and lubricating .... 7-29
Drive chain slack................................... 7-28
Drive mode switch .................................. 4-5
E
Engine break-in....................................... 6-4
Engine idling speed, checking .............. 7-19
Engine oil and oil filter cartridge ........... 7-13
Engine serial number ............................ 10-1
Engine trouble warning light ................... 4-6
EXUP system ........................................ 4-29
F
Front and rear brake pads, checking.... 7-25
Front fork, adjusting.............................. 4-25
Front fork, checking .............................. 7-33
Fuel ....................................................... 4-20
Fuel consumption, tips for reducing ....... 6-4
Fuel level warning light ........................... 4-6 Fuel tank cap ........................................ 4-20
Fuel tank overflow hose ....................... 4-22
Fuses, replacing ................................... 7-36
H
Handlebar switches ................................ 4-4
Hazard switch......................................... 4-5
High beam indicator light ....................... 4-5
Horn switch ............................................ 4-4
I
Identification numbers .......................... 10-1
Ignition circuit cut-off system............... 4-31
Immobilizer system ................................ 4-1
Immobilizer system indicator light.......... 4-7
Indicator lights and warning lights ......... 4-5
L
License plate light bulb, replacing........ 7-38
M
Main switch/steering lock....................... 4-2
Maintenance and lubrication, periodic ... 7-4
Maintenance, emission control
system.................................................. 7-3
Matte color, caution ............................... 8-1
Model label ........................................... 10-1
Multi-function meter unit ........................ 4-8
N
Neutral indicator light ............................. 4-5
O
Oil level warning light ............................. 4-5
P
Parking ................................................... 6-5
Part locations ......................................... 2-1
Pass switch ............................................ 4-4
Q
Quick shift system .................................. 3-4
R
Rear view mirrors ................................. 4-24
S
Safety information .................................. 1-1
Seats .................................................... 4-23
Shifting ................................................... 6-3
Shift light ................................................ 4-7
Shift pedal ............................................ 4-17
Shock absorber assembly, adjusting ... 4-27
Sidestand ............................................. 4-30
Sidestand, checking and lubricating .... 7-32
Spark plugs, checking .......................... 7-11
Special features...................................... 3-1
Specifications ......................................... 9-1
Starting the engine ................................. 6-2
Steering, checking................................ 7-33
UBN6E1E0.book Page 1 Thursday, October 5, 2017 2:48 PM