(11,1)
北米Model "A1700BE-B" EDITED: 2017/ 10/ 11
General information&California proposition 65
warning
WARNING
Engine exhaust, some of its consti-
tuents, and certain vehicle compo-
nents contain or emit chemicals
known to the State of California to
cause cancer and birth defects or
other reproductive harm. In addi-
tion, certain fluids in vehicles and
certain components of product wear
contain or emit chemicals known to
the State of California to cause
cancer and birth defects or other
reproductive harm.&California Perchlorate Advi-
soryCertain vehicle components such as air-
bag modules, seatbelt pretensioners and
keyless entry transmitter batteries may
contain perchlorate material. Special
handling may apply for service or vehicle
end of life disposal. See www.dtsc.ca.gov/
hazardouswaste/perchlorate.
&Noise from under the vehicle
NOTEYou may hear a noise from under the
vehicle approximately 5 to 10 hours
after the engine is turned off. However,
this does not indicate a malfunction.
This noise is caused by the operation of
the fuel evaporation leakage checking
system and the operation is normal.
The noise will stop after approximately
15 minutes.&Event data recorderThis vehicle is equipped with an event data
recorder (EDR). The main purpose of an
EDR is to record, in certain crash or near
crash-like situations, such as an air bag
deployment or hitting a road obstacle, data
that will assist in understanding how a
vehicle’s systems performed. The EDR is
designed to record data related to vehicle
dynamics and safety systems for a short
period of time, typically 30 seconds or less.
The EDR in this vehicle is designed to
record such data as:
.How various systems in your vehicle
were operating;
.Whether or not the driver and passen-
ger safety belts were buckled/fastened;
.Howfar(ifatall)thedriverwas
depressing the accelerator and/or brakepedal; and,
.How fast the vehicle was traveling.
These data can help provide a better
understanding of the circumstances in
which crashes and injuries occur. NOTE:
EDR data are recorded by your vehicle
only if a non-trivial crash situation occurs;
no data are recorded by the EDR under
normal driving conditions and no personal
data (e.g., name, gender, age, and crash
location) are recorded. However, other
parties, such as law enforcement, could
combine the EDR data with the type of
personally identifying data routinely ac-
quired during a crash investigation.
To read data recorded by an EDR, special
equipment is required, and access to the
vehicle or the EDR is needed. In addition
to the vehicle manufacturer, other parties,
such as law enforcement, that have the
special equipment, can read the informa-
tion if they have access to the vehicle or
the EDR.
9
0
(29,1)
北米Model "A1700BE-B" EDITED: 2017/ 10/ 11
Function settingsA SUBARU dealer can change the settings of the functions shown in the following table to meet your personal requirements. Contact
your nearest SUBARU dealer for details. In addition, you can change the settings for some of these functions using the multi-function
display (color LCD). For more information, refer to“Multi-function display (color LCD)”F3-44.Item Function Possible settings Default setting Page
Alarm system Alarm system Operation/Non-operation Operation 2-24
Monitoring start delay time (after closure of doors) 0 seconds/30 seconds 30 seconds 2-25
Impact sensor operation (only models with shock
sensors (dealer option))Operation/Non-operation Non-operation 2-30
Passive arming (models without“keyless access
with push-button start system”)Operation/Non-operation Non-operation 2-29
Dome light and map lights (models with moonroof)
illuminationON/OFF OFF 2-24
Keyless access (if equipped) Hazard warning flasher Operation/Non-operation Operation 2-11
Audible signal Operation/Non-operation Operation 2-14
Audible signal volume Level 1 - 7 Level 5 2-14
Door unlock selection function (driver’s door
unlock)Driver’s door only/All
doorsDriver’s door
only2-12
Remote keyless entry system Hazard warning flasher Operation/Non-operation Operation 2-18
Audible signal Operation/Non-operation Operation 2-20
Audible signal volume Level 1 - 7 Level 5 2-20
Remote trunk open function Activation of trunk opening by remote transmitter/
access key fobOperation/Non-operation Operation 2-20
Key lock-in prevention Key lock-in prevention Operation/Non-operation Operation 2-7
Defogger and deicer system for
models with the automatic climate
control systemRear window defogger, outside mirror defogger
and windshield wiper deicerOperation for 15 minutes/
Continuous operationOperation for
15 minutes3-84
–CONTINUED–
27
0
(101,1)
北米Model "A1700BE-B" EDITED: 2017/ 10/ 11
Keys.........................................................................2-2
Models without“keyless access with push-button
start system”....................................................... 2-2
Models with“keyless access with push-button
start system”....................................................... 2-2
Key number plate................................................... 2-3
Door locks...............................................................2-4
Locking and unlocking from the outside................. 2-4
Locking and unlocking from the inside................... 2-5
Battery drainage prevention function...................... 2-6
Power door lockingswitches................................2-7
Key lock-in prevention function.............................. 2-7
Keyless access with push-button start system
(if equipped).........................................................2-8
Safety precautions................................................. 2-8
Locking and unlocking by holding the access key
fob......................................................................2-10
Unlock using PIN Code Access.............................2-12
Power saving function..........................................2-13
Selecting audible signal operation.........................2-14
Warning chimes and warning indicator..................2-14
Disabling keyless access function.........................2-14
When access key fob does not operate properly ... 2-16
Replacing battery of access key fob......................2-16
Replacing access key fob.....................................2-16
Certification for keyless access with push-button
start system........................................................2-16
Tips......................................................................2-17
Remote keyless entrysystem.............................2-18
Locking the doors................................................2-19
Unlocking the doors.............................................2-19
Opening the trunk lid............................................2-20
Vehicle finder function..........................................2-20
Sounding a panic alarm........................................2-20
Selecting audible signal operation (models
without“keyless access with push-button start
system”)............................................................2-20
Replacing the battery............................................2-21
Replacing lost transmitters...................................2-21
Certification for Remote keyless entry system.......2-21
Anti-theft system..................................................2-22
Immobilizer...........................................................2-22
Alarm system.......................................................2-24
Child safety locks.................................................2-31
Windows................................................................2-31
Power window operation by driver........................2-32
Power window operation by passengers...............2-34
Off delay function.................................................2-35
Initialization of power window ...............................2-35
Trunk lid................................................................2-35
To open and close the trunk lid from outside........2-36
To open the trunk lid from inside..........................2-36
Internal trunk lid release handle............................2-36
Moonroof (if equipped).........................................2-38
Moonroof switches...............................................2-39
Sun shade............................................................2-40
Keys and doors
2
(102,1)
北米Model "A1700BE-B" EDITED: 2017/ 10/ 11
Keys
CAUTION
When traveling in an airplane, do not
press the button of the key. If any
button of the key is pressed, radio
waves are emitted and may affect
the operation of the airplane. When
carrying the key in a bag, take
measures to prevent the buttons
from being pressed accidentally.NOTEPress the buttons of the key to lock/
unlock with the remote keyless entry
system. For details, refer to“Remote
keyless entry system”F2-18.
&Models without“keyless ac-
cess with push-button start
system”1) Master key
2) Submaster key
3) Sub key
4) Key number plateThree types of keys are provided for your
vehicle.
CAUTION
Do not attach a large key holder or
key case to either key. If it bangs
against your knees while you are
driving, it could turn the ignition
switch from the“ON”position to
the“ACC”or“LOCK”position,
thereby stopping the engine.&Models with“keyless access
with push-button start sys-
tem”1) Access key fob (main)
2) Access key fob (sub)
3) Key number plateThe vehicle has two access key fobs and a
Keys and doors/Keys
2-2
(104,1)
北米Model "A1700BE-B" EDITED: 2017/ 10/ 11
Door locks&Locking and unlocking from
the outside
NOTEIf you unlock the driver’s door with a
key (including an emergency key) and
open the door while the alarm system is
armed, the alarm system is triggered
and the vehicle’s horn sounds. In this
case, perform any of the following
operations:
Models with“keyless access with
push-button start system”:
.Press any button on the access key
fob (except when the battery of the
access key fob is discharged).
.Turn the push-button ignition switch
to the“ACC”position.
Models without“keyless access with
push-button start system”:
.Press any button on the remote
transmitter (except when the transmit-
ter battery is discharged).
.Insert the key into the ignition switch
and turn the ignition switch to the“ON”
position.
For details about the alarm system,
refer to“Alarm system”F2-24.
To lock the driver’s door from the outside
with the key, turn the key toward the front.
To unlock the door, turn the key toward the
rear. Pull the outside door handle to open
an unlocked door.
NOTEThe emergency key is directional. If the
key cannot be inserted, change the
direction that the grooved side is facing
and insert it again.
To lock the door from outside without the
key, the following methods are available.
Keys and doors/Door locks
2-4
(107,1)
北米Model "A1700BE-B" EDITED: 2017/ 10/ 11
Power door locking switches1) Lock
2) UnlockAll doors can be locked and unlocked by
the power door locking switches located at
the driver’s side and the front passenger’s
side doors.
To lock the doors, push the front side of the
switch.
To unlock the doors, push the rear side of
the switch.
When you close the doors after you set the
door locks, the doors remain locked.
NOTEMake sure that you do not leave the key
inside the vehicle before locking the
doors from the outside using the power
door locking switches.&Key lock-in prevention func-
tionThis function prevents the doors from
being locked under the following condi-
tions.
.The key is still in the ignition switch
(models without“keyless access with
push-button start system”)
.The ignition switch is in the“ON”
position (models with“keyless access with
push-button start system”)
This function’s operational/non-opera-
tional setting can be changed by a
SUBARU dealer. Contact a SUBARU
dealer for details.NOTE.The factory setting (default setting)
for this function is set as“operational”.
.When leaving the vehicle, make sure
you are holding the key before locking
the doors.!Behavior with key lock-in preven-
tion function operational
With the driver’s door open, the doors are
automatically kept unlocked even if the
front side of the power door locking switch
is pressed.
!Behavior with key lock-in preven-
tion function non-operational
.If the lock lever is turned to the front
(“LOCK”) position with the driver’s door
open and the driver’s door is then closed
with the lock lever in that position, the
driver’s door is locked.
.If the spare key is used to lock the
driver’s door from the outside of the
vehicle, the door is locked.
Keys and doors/Power door locking switches
2-7
2
(108,1)
北米Model "A1700BE-B" EDITED: 2017/ 10/ 11
Keyless access with push-
button start system (if
equipped)You can perform the following operations
using“keyless access with push-button
start system”when you are holding the
access key fob.
.Locking and unlocking of the doors
.Opening the trunk
.Starting and stopping the engine. For
details, refer to“Models with push-button
start systems”F7-11.
.Arming and disarming the alarm sys-
tem. For details, refer to“Alarm system”
F2-24.&Safety precautions!Regarding radio wave
WARNING
If you wear an implanted pacemaker
or an implanted defibrillator, stay at
least 8.7 in (22 cm) away from the
transmitting antennas installed on
the vehicle.
The radio waves from the transmit-
ting antennas on the vehicle could
adversely affect the operation ofimplanted pacemakers and im-
planted defibrillators.
If you wear electric medical equip-
ment other than an implanted pace-
maker or an implanted defibrillator,
before using the keyless access
with push-button start system, refer
to“Radio waves used for the key-
less access with push-button start
system”F2-9, and contact the elec-
tric medical equipment manufac-
turer for more information. The radio
waves from the transmitting anten-
nas on the vehicle could adversely
affect the operation of the electric
medical equipment.
NOTEThe status of the access key fob and
environmental conditions may interfere
with the communication between the
access key fob and the vehicle under
the following conditions.
.When you operate near a source of
strong radio waves or other interfer-
ence, such as a broadcast station or
power transmission lines
.When products that transmit radio
waves are used, such as an access key
fob or a remote transmitter key fob of
another vehicle.When you carry the access key fob
of your vehicle together with an access
key fob or a remote transmitter of
another vehicle
.When the access key fob is placed
near wireless communication equip-
ment such as a cell phone, or near a
metallic object
.When metallic accessories are at-
tached to the access key fob
.When you carry the access key fob
with electronic appliances such as a
laptop computer
.When the battery of the access key
fob is discharged
In such cases, it may not be possible to
lock or unlock the doors or start the
engine.
!Regarding malfunction
CAUTION
.Never leave or store the access
key fob inside the vehicle or
within 6.6 ft (2 m) around the
vehicle (e.g., in the garage). The
access key fob may be locked
inside the vehicle, or the battery
may discharge rapidly. Note that
the push-button ignition switch
may not turn on in some cases
Keys and doors/Keyless access with push-button start system
2-8
(109,1)
北米Model "A1700BE-B" EDITED: 2017/ 10/ 11
depending on the location of the
access key fob.
.The access key fob contains
electronic components. Observe
the following precautions to pre-
vent malfunctions or battery dis-
charge.
–It is recommended that the
battery be replaced by a
SUBARU dealer to avoid the
damage at the time of replace-
ment.
–Do not get the access key fob
wet. If the access key fob gets
wet, wipe it off immediately
and let it dry completely.
–Do not apply strong impacts to
the access key fob.
–Never leave the access key
fob in direct sunlight or any-
where that may become hot,
such as on the dashboard.
–Do not wash the access key
fob in an ultrasonic washer.
–Do not leave the access key
fob in humid or dusty loca-
tions, or near personal com-
puters or home electric appli-
ances.
–Keep the access key fob awayfrom magnetic sources.
–Do not leave the access key
fob near a battery charger or
any electrical accessories.
–Do not apply metallic window
tint or attach metallic objects
to the windows.
–Do not fit non genuine acces-
sories or parts.
NOTEAfter the vehicle battery is discharged
or replaced, initialization of the steering
lock system may be required to start
the engine. In this case, perform the
following procedure to initialize the
steering lock.
1) Turn the push-button ignition
switch to the“OFF”position. For de-
tails, refer to“Switching power status”
F3-7.
2) Open and close the driver’s door.
3) Wait for approximately 10 seconds.
When the steering is locked, the initi-
alization is completed.!Regarding setting
NOTE.You can change the operational/non-
operational setting for the keyless
access function. For the setting proce-
dure, refer to“Disabling keyless ac-
cess function”F2-14. The setting can
also be changed by a SUBARU dealer.
For more details, contact a SUBARU
dealer.
.For detailed information about the
operation method for the push-button
ignition switch while the keyless ac-
cess function is switched to the non-
operational mode, refer to“Access key
fob–if access key fob does not operate
properly”F9-26.
!Radio waves used for the keyless
access with push-button start sys-
tem
The keyless access with push-button start
system uses radio waves of 134 kHz, in
addition to the radio waves used for the
remote keyless entry system. The radio
waves are periodically output from the
antennas installed on the vehicle as shown
in the following illustration.
–CONTINUED–
Keys and doors/Keyless access with push-button start system
2-9
2