2018 SUBARU WRX driver seat adjustment

(33,1)
北米Model "A1700BE-B" EDITED: 2017/ 10/ 11
Front seats..............................................................1-2
Manual seat........................................................... 1-4
Power seat (driver’s seat–if equipped) .................. 1-5
Head restraint adjustment...................................... 1-5
Seat heater (ifequipped)........................................1-7
Rear seats................................................................1-8
Head restraint adjustment...................................... 1-8
Folding down the rear seatback............................1-10
Armrest (except TYPE RA)....................................1-12
Seatbelts................................................................1-12
Seatbelt safety tips...............................................1-12
Emergency Locking Retractor (ELR)......................1-13
Automatic Locking Retractor/Emergency Locking
Retractor (ALR/ELR)............................................1-13
Seatbelt warning light and chime..........................1-14
Fastening the seatbelt...........................................1-14
Seatbelt maintenance............................................1-17
Front seatbelt pretensioners................................1-17
Driver’s seatbelt....................................................1-18
Front passenger’s seatbelt....................................1-18
Components that will operate with the seatbelt
pretensioner(s) simultaneously...........................1-19
Safety tips............................................................1-20
System monitors...................................................1-20
System servicing..................................................1-20
Precautions against vehicle modification...............1-21
Child restraint systems........................................1-21
Safety tips for installing child restraint systems .... 1-22
Where to place a child restraint system................1-23
Choosing a child restraint system.........................1-25
Installing child restraint systems with ALR/ELR
seatbelt.............................................................1-25
Installing a booster seat.......................................1-29
Installation of child restraint systems by use of
lower and tether anchorages (LATCH)................1-30
Top tether anchorages..........................................1-32
*SRS airbag
(Supplemental Restraint Systemairbag).........1-33
General precautions regarding SRS airbag
system..............................................................1-34
General precautions regarding SRS airbag
system for accessories and any objects.............1-36
General precautions regarding SRS airbag
system for children............................................1-38
Components.........................................................1-41
SUBARU advanced frontal airbag system..............1-43
SRS side airbag and SRS curtain airbag...............1-53
SRS airbag system monitors.................................1-62
SRS airbag system servicing ................................1-63
Precautions against vehicle modification..............1-64
How to contact the vehicle manufacturer
concerning modifications for persons with
disabilities that may affect the advanced airbag
system..............................................................1-65Seat, seatbelt and SRS airbags
1

(36,1)
北米Model "A1700BE-B" EDITED: 2017/ 10/ 11
&Manual seat!Forward and backward adjustment1. Sit in the seat to adjust.
2. Pull the lever upward, slide the seat to
the desired position, and then release the
lever.
3. Try to move the seat back and forth to
make sure that it is securely locked into
place.!Reclining the seatback
1. Pull up the reclining lever, adjust the
seatback to the desired position, and then
release the lever.
2. Make sure the seatback is securely
locked into place.
The seatback placed in a reclined position
can spring back upward with force when
pulling the lever. While operating the lever
to return the seatback, hold the seatback
lightly so that it may be raised back
gradually.!Seat cushion height adjustment
(driver’s seat)
1) When the lever is pushed down, the seat
is lowered.
2) When the lever is pulled up, the seat
rises.Move the seat cushion adjustment lever up
or down to adjust the seat cushion height.
Seat, seatbelt and SRS airbags/Front seats
1-4

(37,1)
北米Model "A1700BE-B" EDITED: 2017/ 10/ 11
&Power seat (driver’s seat–if
equipped)1)Seat position forward/backward con-
trol switch
To adjust the seat forward or backward,
move the control switch forward or
backward. During forward/backward ad-justment of the seat, you cannot adjust
the seat cushion angle or seat cushion
height.
2)Seat cushion angle control switch
To adjust the seat cushion angle, pull up
or push down the front end of the control
switch.
3)Seat height control switch
To adjust the seat height, pull up or push
down the rear end of the control switch.
4)Seatback angle (reclining) control
switch
To adjust the angle of the seatback, move
the control switch.
5)Lumbar support control switch (dri-
ver’s seat only)
To increase lower back support, push the
front side of the switch. To decrease
lower back support, push the rear side of
the switch.
&Head restraint adjustment
WARNING
.Never drive the vehicle with the
head restraints removed because
they are designed to reduce the
risk of serious neck injury in the
event that the vehicle is struck
from the rear. Also, never install
the head restraints the opposite
way round. Doing so will prevent
the head restraints from function-ing as intended. Therefore, when
you remove the head restraints,
you must reinstall all head re-
straints correctly to protect vehi-
cle occupants.
.All occupants, including the dri-
ver, should not operate a vehicle
or sit in a vehicle’s seat until the
head restraints are placed in their
proper positions in order to mini-
mize the risk of neck injury in the
event of a crash.
.The front seat head restraints are
designed to be installed into the
front seats only. The rear seat
head restraints are designed to
be installed into the rear seats
only. Do not attempt to install the
front seat head restraints into the
rear seats, or the rear seat head
restraints into the front seats.
NOTEIt is possible to adjust the angle of the
front seat head restraints only. When
installing the front seat head restraints,
make sure that the angle of the head
restraints can be adjusted.
Both the driver’s seat and front passen-
ger’s seat are equipped with head re-
straints. Both head restraints are adjusta-
–CONTINUED–
Seat, seatbelt and SRS airbags/Front seats
1-5
1

(370,1)
北米Model "A1700BE-B" EDITED: 2017/ 10/ 11
served, there are no stored diagnostic
trouble codes, and the OBDII readiness
monitors are all complete.
.A vehicle fails the OBDII inspection if
the“CHECK ENGINE”warning light is not
properly operating (light is illuminated or is
not working due to faulty LED [Light
Emitting Diode]) or there is one or more
diagnostic trouble codes stored in the
vehicle’s computer.
.A state emission inspection may reject
(not pass or fail) a vehicle if the number of
OBDII system readiness monitors“NOT
READY”is greater than one. If the
vehicle’s battery has been recently re-
placed or disconnected, the OBDII system
inspection may indicate that the vehicle is
not ready for the emission test. Under this
condition, the vehicle driver should be
instructed to drive his/her vehicle for a
few days to reset the readiness monitors
and return for an emission re-inspection.
.Owners of rejected or failing vehicles
should contact their SUBARU Dealer for
service.
Some states still use dynamometers in
their emission inspection program. A
dynamometer is a treadmill or roller-like
testing device that allows your vehicle’s
wheels to turn while the vehicle remains in
one place. Prior to your vehicle being puton a dynamometer, tell your emission
inspector not to place your SUBARU
AWD vehicle on a two-wheel dynam-
ometer.Otherwise, serious transmis-
sion damage will result.
The U.S. Environmental Protection
Agency (EPA) and states using two-wheel
dynamometers in their emission testing
program have EXEMPTED SUBARU
AWD vehicles from the portion of the
testing program that involves a two-wheel
dynamometer. There are some states that
use four-wheel dynamometers in their
testing program. When properly used, this
equipment should not damage a SUBARU
AWD vehicle.
Under no circumstances should the rear
wheels be jacked off the ground, nor
should the driveshaft be disconnected in
an attempt to bypass AWD for state
emission testing. An AWD vehicles must
be tested using an AWD dynamometer
with all 4 wheels driven and loaded.
Preparing to driveYou should perform the following checks
and adjustments every day before you
start driving.
1. Check that all windows, mirrors, and
lights are clean and unobstructed.
2. Check the appearance and condition
of the tires. Also check tires for proper
inflation.
3. Look under the vehicle for any sign of
leaks, and check that no small animal is
under the vehicle.
4. Check that no small animal enters the
engine compartment.
5. Check that the hood and trunk lid are
fully closed.
6. Check the adjustment of the seat.
7. Check the adjustment of the inside and
outside mirrors.
8. Fasten your seatbelt. Check that your
passengers have fastened their seatbelts.
9. Check the operation of the warning
and indicator lights when the ignition
switch is turned to the“ON”position.
10. Check the gauges, indicator and warn-
ing lights after starting the engine.
Starting and operating/Preparing to drive
7-8