2018 Peugeot iOn lock

89
F Connect one end of the red cable to the (+ ) terminal of the flat battery A , then the
other end to the ( +) terminal of the back-up
battery
B .
F
C
onnect one end of the green or black
cable to the (-) terminal of the back-up
battery B .
F

C

onnect the other end of the green or black
cable to the earth point C of your broken
down vehicle. F

S
tart the engine of the vehicle with the good
battery and wait for a few minutes.
F
O
perate the ignition switch of your vehicle
until the "Ready" lamp comes on.
F
D
isconnect the jump cables in reverse
o r d e r.
F
R
efit the protective cover on the battery and
tighten the retaining nut.
If the "Ready" warning lamp does not come on,
proceed as follows:
F
L
eave the cables connected.
F
S
et the ignition switch of your vehicle to the
" LOCK " position.
F
C
harge the main battery, following the
normal charging procedure.
F
W
hen the charging indicator lamp comes on
constantly (fixed) in the instrument panel,
disconnect the cables.
F
A
llow the charging to continue for at least
o n e h o u r.
F
O
perate the ignition switch of your vehicle
until the "Ready" lamp comes on.
If the problem persists, contact a PEUGEOT
dealer or a qualified workshop.
Charging the battery using
a battery charger
F Remove the battery protective cover.
Make sure the electrolyte is not frozen.
Check the level and top up with distilled
water, if necessary.
For more information on Checking levels ,
refer to the corresponding section.
F

U
nscrew nut 1 and remove the retaining
clip.
8
In the event of a breakdown

91
Removing the rear seatRemoving the metal cover plate
F Pull the controls A for wards to unlock the
two seat locks.
F

R
aise the front of the seat and tip upwards
to remove it.
Refitting the rear seat
When refitting the seat, take care not to
trap the seat belt buckles.
Composition of the kit
F Loosen the four "butterfly" screws.
F R emove the metal cover plate.
You can then access the repair kit.
F

P
ut the metal cover plate back in place.
F

R
etighten the four "butter fly" screws. F

I
nsert the metal hooks into the bench seat
backrest.
F
T
ip the seat downwards and press to lock
the two locks.
F
C
heck that the seat is locked properly.
1. 12 V compressor with a built-in pressure
gauge to check and adjust the pressure
of the tyre.
8
In the event of a breakdown

93
Take care, this product is harmful if
swallowed and causes irritation to the
eyes.
Keep this product out of the reach of
children.
The use-by date is marked on the bottle.
After use, do not discard the bottle by the
roadside, take it to a PEUGEOT dealer or
an authorised waste disposal site.
Do not forget to obtain a new sealant
bottle, available from a PEUGEOT dealer
or a qualified workshop.
Inflation
F Check that switch A of the compressor is in the " OFF" position.
F

Un
coil the compressor hose B fully.
F

C
onnect the hose to the sealed tyre's valve.
F

C
onnect the compressor's electrical
connector to the vehicle's 12V socket
(ignition switch in "ON" or "ACC" position).
F

S
witch on the compressor by setting
switch
A in the "ON" position.
F

A
djust the pressure using the compressor in
accordance with the vehicle's tyre pressure
label located on the driver's door aperture.
A significant loss of pressure indicates that
the puncture has not been fully sealed;
contact a PEUGEOT dealer or qualified
workshop for your vehicle to be repaired.
F

R
emove the compressor and stow the kit.
F

D
rive immediately at reduced speed
(50
mph (80 km/h) max) limiting the
distance travelled to approximately
120
miles (200 km).
If after approximately five to seven
minutes, the required pressure is not
reached, this indicates that the tyre is not
repairable; contact a PEUGEOT dealer or
a qualified workshop for your vehicle to be
recovered.
F
R
emove the injection hose.
F
R
eplace the valve core using the tool. As soon as possible, go to a PEUGEOT
dealer or a qualified workshop.
You must inform the technician that you
have used this kit. After inspection, the
technician will let you know if the tyre can
be repaired or if it must be replaced.
Spare wheel
Scan the QR code on page 3 to view
explanatory videos.
Parking the vehicle
Park the vehicle where it does not block
traffic: the ground must be level, stable
and non-slippery.
Apply the parking brake, switch off the
ignition and put the drive selector in
position P in order to block the wheels.
If necessary, place a chock under the
wheel diagonally opposite to the wheel to
be changed.
Make absolutely certain that all the
occupants have left the vehicle and are
waiting in a safe area.
Never go underneath a vehicle raised
using a jack; use an axle stand.
8
In the event of a breakdown

98
Front foglamps/Daytime running
lampsIntegrated direction indicator
side repeaters (WY5W – 5
W)
Dipped beam headlamps
F Turn the bulb holder to the left and pull it
out.
F

R
emove the bulb by pressing the tab.
F

R
eplace the bulb.
To refit, carry out these operations in reverse
o r d e r. F

T
urn your wheels to full lock for easier
access.
F
R
emove the clips retaining the bulb holder
protective cover.
F
M
ove the cover aside.
F
T
urn the bulb holder (A for foglamps, B
for daytime running lamps) to the left and
remove it.
F

R
emove the bulb and replace it.
To refit, carry out these operations in reverse
o r d e r. F

P
ush the repeater towards the rear and
release it.
F

T
urn the bulb holder to the left and
remove
it.
F

R
emove the bulb and replace it.
To refit, carry out these operations in reverse
o r d e r.
In the event of a breakdown

101
Changing a fuse
Access to the tools
The extraction tweezers are fitted to the back
of the dashboard fusebox cover.
To access them:
F
U
nclip the protective cover and remove it
completely by pulling it towards you.
F

P
ull out the tweezers.
Changing a fuse
Good Failed
Tw e e z e r s
Before changing a fuse, the cause of the fault
must be found and rectified.
F

M

ake sure that the ignition switch is set to
the " LOCK " position.
F

I

dentify the failed fuse by checking the
condition of its filament.
F

U

se the special tweezers to extract the fuse
from its housing.
F

A

lways replace the faulty fuse with a fuse of
the same rating.
F

C

heck that the number marked on the
fusebox, the rating marked on the fuse and
the following tables all agree. Your vehicle's electrical system is
designed to operate with standard or
optional equipment.
Before installing other electrical
equipment or accessories on your vehicle,
contact a PEUGEOT dealer or a qualified
workshop.
PEUGEOT accepts no responsibility for
the cost incurred in repairing your vehicle
or for rectifying malfunctions resulting
from the installation of accessories
not supplied and not recommended by
PEUGEOT and not installed in accordance
with its specifications, in particular when
the combined power consumption of all
of the additional equipment connected
exceeds 10
mil

liamperes.
F

T

urn the bulb holder and remove it.
F

R

emove the bulb and replace it.
To refit, carry out these operations in reverse
o r d e r.
8
In the event of a breakdown

102
Fuses in the dashboard
The fusebox is located in the lower dashboard.
Access to the fuses
F
U
nclip the protective cover and remove it
completely by pulling it towards you. Fuse No.
Rating Functions
1 7. 5 AFront and rear left sidelamps.
2 15 AAccessory socket.
3 -Not used.
4 7. 5 AStarter motor.
5 20 AAudio system.
6 -Not used.
7 7. 5 ADashboard consumers, front and rear right sidelamps.
8 7. 5 AElectric door mirrors.
9 7. 5 ASupervisor.
10 7. 5 AAir conditioning.
11 10 ARear foglamp.
12 15 ADoor locks.
13 10 ACourtesy lamp.
In the event of a breakdown

105
Towing the vehicle
Procedure for having your vehicle towed using
a fixed towing eye.General recommendations
Obser ve the legislation in force in your
c o u nt r y.
Ensure that the weight of the towing
vehicle is higher than that of the towed
vehicle.
The driver must remain at the wheel of
the towed vehicle and must have a valid
driving licence.
When towing a vehicle with all four
wheels on the ground, always use an
approved towing arm; rope and straps are
prohibited.
The towing vehicle must move off gently.
When the vehicle is towed with its engine
off, there is no longer braking and steering
assistance.
In the following cases, you must always
call on a professional recovery ser vice:
-

v
ehicle broken down on a motor way or
main road,
-
f

our-wheel drive vehicle,
-

w
hen it is not possible to put the
gearbox into neutral, to unlock the
steering, or to release the parking
brake,
-

t
owing with only two wheels on the
ground,
-

w
here there is no approved towbar
available.
Towing your vehicle
The towing eye is welded to the chassis under
the front bumper.
F

I
nstall the towbar.
F

S
tart your vehicle ("Ready" lamp on).
F

M
ove the drive selector to position N .
F

R
elease the parking brake.
F

T
urn on your vehicle's hazard warning
lamps.
F

H
ave your vehicle towed for no more than
20
miles (30 km) without exceeding the
speed of 20
mph (30 km/h).
Failure to comply with these operations
may cause damage to the braking
components and the electric motor.
Towing another vehicle
Your vehicle cannot in any circumstances
be used to tow another vehicle.
8
In the event of a breakdown

2
Select preset radio station.
Radio, press and hold: store a
station.
Other than radio: see the
corresponding sections.
Eject CD.
Select the source:
Radio: FM1, FM2, CD, USB, AUX,
Streaming.
Telephone: accept an incoming call.
Telephone, press and hold: end
a call, access the calls log for the
connected telephone.
Radio
Presetting a station
Press SRC/TEL repeatedly to select
the FM1, FM2 or AM waveband.
Press and hold a button to preset
the station being listened to. The
name of the station is displayed and
an audible signal confirms that it has
been preset. The external environment (hills, buildings,
tunnels, basement car parks, etc.) may
block reception, including in RDS tracking
mode. This is a normal effect of the way
in which radio waves are transmitted and
does not indicate any failure of the audio
equipment.
Selecting a station
Press a button to listen to the
corresponding preset station.
Managing a list
Press LIST
to display the list of
stations received in alphabetical
o r d e r.
Select the desired radio station
using one of the buttons.
Confirm with " OK".
Briefly press one of the buttons to
change to the next or previous letter.
Press and hold LIST to build or
update the list of stations; audio
reception is cut momentarily.
Entering a frequency
Press MENU .
Select "Radio ".
Select "Enter or Write freq. ".
Press + ,
or press – to select the desired
frequency.
Confirm with " OK".
RDS
RDS, if activated, allows you to
continue listening to the same station
by automatically retuning to alternative
frequencies. However, in certain conditions,
coverage of an RDS station may not be
assured throughout the entire country as
radio stations do not cover 100% of the
territory. This explains the loss of reception
of a station that can occur during a journey.
With source FM1 or FM2, press
MENU .
Select "Radio ".
Bluetooth® audio system