2018 Peugeot 208 parking brake

85
F Move the gear lever to M.
F
P
ush the lever for ward to change
up.
F

P
ull the lever back to change
down.
Invalid value
This symbol is displayed if a gear
i s not engaged correctly (selector
between two positions).
You can change from position D to M and
from M to D at any time.
When the engine is running at idle with the
brakes released, if position R , D or M is
selected, the vehicle moves even without
the accelerator being pressed.
Never leave children unattended in the
vehicle when the engine is running.
When carrying out maintenance with the
engine running, apply the parking brake
and select position P . Never select position N while the vehicle
is moving.
Never select position P or R unless the
vehicle is completely stationary.
If position N is selected inadvertently while
driving, allow the engine to return to idle,
then select position D to accelerate.
If the temperature is below -23°C, the
engine should be left at idle for 4
minutes,
to ensure the correct operation and
service life of the engine and gearbox.
Sport and snow programmes
These two special programmes supplement the
automatic operation in very specific conditions
of use.
Sport programme " S"
F Press button " S" after starting the engine.
The gearbox automatically favours a dynamic
style of driving.
S appears in the instrument panel.
Snow programme T
(Depending on engine.)
F P ress the " T" button, after starting the
engine.
The gearbox adapts to driving on slippery
roads.
This programme improves starting and traction
when grip is poor.
T appears in the instrument panel.
At any time, press the selected button
again to quit the activated programme and
return to auto-adaptive mode.
Return to automatic
operation
F At any time, press button S or T again to quit the programme engaged and return to
auto-adaptive mode.
Stopping – Parking
Before switching off the engine.
F E ngage position P or N .
F

A
pply the parking brake.
F

Imm
obilise the vehicle.
6
Driving

86
If the lever is not in position P, an alert
message appears on the screen on
opening the driver's door or approximately
45
seconds after switching off the ignition.
F

R
eposition the lever at position P ; the
message disappears.
When driving on flooded roads or when
crossing a
ford, proceed at walking pace.
When the ignition is on, the lighting
of this warning lamp, accompanied
by an audible signal and a
message
on the screen, indicates a
gearbox
fault.
In this case, the gearbox goes into back-up
mode by staying in 3rd gear. You may feel
a

substantial jolt when changing from P to
R and from N to R . This will not cause any
damage to the gearbox.
Do not exceed 62
mph (100 km/h), local speed
restrictions permitting.
Contact a
PEUGEOT dealer or a qualified
workshop as soon as possible. There is a
risk of damage to the gearbox:
F i f you press the accelerator and brake
pedals at the same time,
F

w
ith a flat battery, if you force the
movement of the lever from position P
to another position.
To reduce fuel consumption during
prolonged stops with the engine running
(e.g. traffic jam), position the gear lever at
N and apply the parking brake.
Gear shift indicator
(Depending on engine.)
System which reduces fuel consumption by
recommending the most appropriate gear.
Operation
Depending on the driving situation and your
vehicle's equipment, the system may advise
you to skip one or more gears. You can
follow this indication without engaging the
intermediate gears.
Gear shift recommendations must not be
considered as compulsory. In fact, the road
layout, the traffic density and safety remain the
deciding factors when choosing the best gear. With an automatic gearbox, the system is
only active in manual operation.
The information appears in the
instrument panel, in the form of an
ascending or descending arrow and
the recommended gear.
The system adapts its gear shift
recommendation according to the driving
conditions (slope, load, etc.) and the
driver's requirements (power, acceleration,
b r a k i n g , e t c .) .
The system never suggests:
-
e
ngaging first gear,
-
enga
ging reverse.
On vehicles fitted with a manual gearbox,
the arrow may be accompanied by the
gear recommended. The system always
recommends to change up if necessary.
Depending on the engine, it may also
recommend to change down if necessary.
The driver therefore remains responsible for
deciding whether or not to follow the indications
issued by the system.
This function cannot be deactivated.
Driving

87
Hill start assist
System that holds your vehicle for around
2 seconds, the time it takes to move your foot
from the brake pedal to the accelerator pedal.
The hill start assist function cannot be
deactivated. However, use of the parking
brake to immobilise the vehicle interrupts
its function. Hill start assist is only available when:
-

y
our foot on the brake pedal fully
immobilises the vehicle,
-

c
ertain slope conditions are met,
-

t
he driver's door is closed.Do not leave the vehicle while it is being
held temporarily by hill start assist.
If you need to leave the vehicle with the
engine running, apply the parking brake
manually. Then ensure that the parking
brake warning lamp is on fixed in the
instrument panel.
Malfunction
If a fault in the system occurs, these warning
l amps come on. Contact a PEUGEOT dealer
or a
qualified workshop to have the system
checked.
Uphill, with the vehicle stationar y, the
vehicle is held for a

shor t time when you
release the brake pedal.
With an automatic gearbox, if you are in
position D . Downhill, with the vehicle stationary and
reverse gear engaged, the vehicle is held
for a

shor t time when you release the brake
pedal.
Stop & Start
The system puts the engine temporarily into
standby – STOP mode – during stops in the
traffic (red lights, traffic jams, etc.). The engine
restarts automatically – START mode – as
soon as you wish to move off again. Restarting
occurs instantaneously, quickly and silently.
Per fect for urban use, the Stop & Start system
reduces fuel consumption and exhaust
emissions as well as the noise level when
stationary.
STOP mode
This indicator lamp comes on in the
instrument panel and the engine
goes into standby.
With BlueHDi Diesel and manual gearbox :
- A s soon as the vehicle stops or the speed is less
than 2
mph (3 km/h) (with 1.5 BlueHDi engine).
-

W
ith gear lever in neutral and clutch pedal
released.
6
Driving

88
With PureTech petrol and manual or
automatic gearbox:
-

A
s soon as the vehicle stops or the speed
is less than 2
mph (3 km/h) (with manual
gearbox and depending on version).
-

W
ith gear lever in neutral and clutch pedal
released (manual gearbox).
-

W
ith brake pedal pressed or gear lever in
position N (automatic gearbox).
Special cases: STOP mode not
available
STOP mode is not triggered when:
- t he driver's door is open,
-

t
he driver's seat belt is not fastened,
-

t
he vehicle has not exceeded 6 mph
(10
km/h) since the last engine start using
t h e key,
-

t
he engine is needed to maintain
a


comfortable temperature in the passenger
compartment,
-

d
emisting is active,
-

s
ome temporary conditions (battery charge,
engine temperature, braking assistance,
exterior temperature, etc.) make this
necessary to ensure control of a
system.
This indicator lamp flashes for a
few
seconds, then goes off.
This operation is perfectly normal. A time counter calculates the
time spent in STOP mode during
a
journey. It is reset to zero every
time the ignition is switched on
using the key.
For your comfort, during parking
manoeuvres, STOP mode is not available
for a few seconds after coming out of
reverse gear.
The Stop & Start system does not affect
the functionalities of the vehicle, such as
braking.
With a
manual gearbox in STOP mode, if
a
gear is engaged without fully depressing
the clutch pedal, a message is displayed
asking you to depress the clutch pedal
again to restart the engine.
START mode
This indicator lamp goes off and the
engine restarts. With manual gearbox
:
-
W
ith clutch pedal depressed.
With automatic gearbox:
-
W
ith gear lever in position D or M
.
-
W
ith brake pedal released.
or
-
W
ith gear lever in position N.
-
W
ith brake pedal released.
-
T
hen gear lever in position D or M
.
or
-
W
ith reverse gear engaged.
Special cases: START mode
triggered automatically
As a safety measure and for your convenience,
S TART mode is triggered automatically when:
-
y

ou open the driver's door,
-
y

ou unfasten the driver's seat belt,
-

s
ome temporary conditions (battery charge,
engine temperature, braking assistance,
air conditioning setting, etc.) make this
necessary to ensure control of a
system or
the vehicle.
This indicator lamp flashes for a
few
seconds, then goes off.
This operation is perfectly normal.
Never refuel with the engine in STOP
mode; you must switch off the ignition
using the key.
Driving

109
Installation tips
F If you have to fit the chains during a journey,
stop the vehicle on a flat sur face on the side
of the road.
F

A
pply the parking brake and position any
wheel chocks under the wheels to prevent
movement of your vehicle.
F

F
it the chains following the instructions
provided by the manufacturer.
F

M
ove off gently and drive for a few
moments, without exceeding 31
mph
(50


km/h).
F

S
top your vehicle and check that the snow
chains are correctly tightened.
It is strongly recommended that before
you leave, you practise fitting the snow
chains on a
level and dry sur face.
Avoid driving with snow chains on roads
that have been cleared of snow to avoid
damaging your vehicle's tyres and the
road sur face. If your vehicle is fitted with
alloy wheels, check that no part of the
chain or its fixings is in contact with the
wheel rim.
Towing device
Load distribution
F D istribute the load in the trailer so that the
heaviest items are as close as possible to
the axle and the nose weight approaches
the maximum permitted without exceeding
it.
Air density decreases with altitude, thus
reducing engine performance. The maximum
towed load must be reduced by 10% for every
1,000
metres of altitude.
Use towing devices and their genuine
harnesses approved by PEUGEOT. It
is recommended that the installation
be per formed by a
PEUGEOT dealer or
a


qualified workshop.
If the towing device is not fitted by
a
PEUGEOT dealer, it must still be
fitted in accordance with the vehicle
manufacturer's instructions.
Certain driving assistance or manoeuvring
assistance functions are automatically
disabled if an approved towing device is
used. Obser ve the maximum authorised towable
weight, indicated on your vehicle's
registration certificate, the manufacturer's
label as well as in the Technical data

section of this guide.
Complying with the maximum
authorised nose weight (towball)
also includes the use of accessories
(bicycle carriers, tow boxes, etc.).
Obser ve the legislation in force in the
country in which you are driving.
Load reduction mode
System which manages the use of certain
functions according to the level of charge
remaining in the battery.
When the vehicle is being driven, the load
reduction function temporarily deactivates
certain functions, such as air conditioning,
heated rear screen, etc.
The deactivated functions are reactivated
automatically as soon as conditions permit.
7
Practical information

116
Manual gearbox
The gearbox does not require any
maintenance (no oil change).
Automatic gearbox
The gearbox does not require any
maintenance (no oil change).
Brake pads
Brake wear depends on the style
of driving, particularly in the case
of vehicles used in town, over short
distances. It may be necessary to
have the condition of the brakes
checked, even between vehicle
services.
Unless there is a
leak in the circuit, a drop in
the brake fluid level indicates that the brake
pads are worn.
Brake disc/drum wear
For any information on checking
brake disc/drum wear, contact
a
PEUGEOT dealer or a qualified
workshop.
Parking brake
If excessive travel or a loss of
e ffectiveness of this system is
noticed, the parking brake must
be adjusted, even between two
services.
This system must be checked by a
PEUGEOT
dealer or a
qualified workshop.
Wheels and tyres
The pressure must be checked on
all tyres, including the spare wheel,
when the tyres are "cold", at least
once a month and before a long
j o u r n ey. steering. Regular inspections of the condition
of tyres (tread and sides) and rims are
recommended as well as making sure that
valves are fitted.
Using different size wheels and tyres from
those specified can affect the lifetime of tyres,
wheel rotation, ground clearance and the
speedometer reading and have an adverse
effect on road holding.
Fitting different tyres on the front and rear axles
can cause the ESC to mistime.
Only use products recommended by
PEUGEOT or products of equivalent
quality and specification.
In order to optimise the operation of
components as important as those in the
braking system, PEUGEOT selects and
offers very specific products.
After washing the vehicle, dampness, or
in wintry conditions, ice can form on the
brake discs and pads: braking efficiency
may be reduced. Make light brake
applications to dry and defrost the brakes.
The pressures given on the tyre pressure label
are valid for "cold" tyres. If you have driven for
more than 10
minutes or more than 6 miles
(10

kilometres) at more than 31 mph (50 km/h),
0.3

bar (30 kPa) should be added to the values
given on the label.
Under-inflation increases fuel consumption.
Non-compliant tyre pressure causes premature
wear on tyres and has an adverse effect on the
vehicle's road holding – Risk of an accident!
Driving with worn or damaged tyres reduces
braking efficiency and control of the vehicle's
Practical information

122
Temporary puncture
repair kit
Scan the QR code on page 3 to view
e xplanatory videos.
Comprising a
compressor and a sealant
cartridge, it allows the temporary repair of
a

tyre so that you can drive to the nearest
garage.
It is designed to repair most punctures which
could affect the tyre, located on the tyre tread
or shoulder.
Access to the kit
This kit is installed in the under floor storage,
under the boot floor. The vehicle's electric system allows the
connection of the compressor for long
enough to inflate a
tyre after a puncture
repair.
Composition of the kit
1. 12 V compressor, with integral pressure
gauge.
2. Sealant cartridge bottle, with integral hose.
3. Speed limit sticker.
Repair procedure
F Park the vehicle without obstructing any
traffic and apply the parking brake.
F

F
ollow the safety instructions (hazard
warning lamps, warning triangle, wearing
high visibility vest, etc.) according to the
legislation in force in the country where you
are driving.
F

S
witch off the ignition. F

U
ncoil the pipe stowed under the
compressor.
Avoid removing any foreign bodies which
have penetrated into the tyre.
F
C
onnect the pipe from the compressor to
the bottle of sealant.
F
T
urn the sealant bottle over and secure it in
the notch provided on the compressor.
In the event of a breakdown

127
Removing a wheel
Parking the vehicle
Immobilise the vehicle where it does not
block traffic: the ground must be level,
stable and non-slippery.
Apply the parking brake.
Switch off the ignition.
With a

manual gearbox, engage first gear
to block the wheels.
With an automatic gearbox, place the
lever in position P to block the wheels.
Check for the fixed illumination of the
parking brake indicator lamps in the
instrument panel.
The occupants must get out of the vehicle
and wait where they are safe.
Never go underneath a
vehicle raised
using a
jack; use an axle stand.
List of operations
F Place the foot of the jack 2 on the ground
and ensure that it is directly below the front
A or rear B jacking point provided on the
underbody, whichever is closest to the
wheel to be changed.
F Remove the bolt cover from each of the bolts using the tool 3 (depending on equipment).
F

F
it the security socket 4 on the wheelbrace
1
to slacken the security bolt (depending on
equipment).
F

S
lacken the other bolts using the
wheelbrace 1
o n l y.
Ensure that the jack is stable on a sur face
t hat is not loose or slippery and positioned
strictly at jacking points A or B under the
vehicle, making sure that the jack head is
centred at the contact point on the vehicle.
Other wise, there is a
risk of damage to
the vehicle and/or of the jack collapsing or
slipping – risk of injury!
F Extend the jack 2 until its head comes
into contact with the jacking point A or B ,
whichever is used; the contact area A or B
on the vehicle must be correctly inserted into
the central part of the head of the jack.
F

Ra
ise the vehicle until there is sufficient
space between the wheel and the ground to
admit the spare (not punctured) wheel easily.
F Remove the bolts and store them in a clean
place.
F

R
emove the wheel.
8
In the event of a breakdown