2018 MITSUBISHI OUTLANDER sensor

Combination headlights and dimmer switch
Features and controls 5-215
5
If the automatic high beam system determinesthat its performance has been degraded, thewarning display will appear.This can occur whenForeign objects, such as dirt, snow or ice,adhere to the windshield of the sensorportion.In adverse weather conditions, such asrain, snow, sand storms, etc.A front vehicle or an oncoming vehicle issplashing water, snow or dirt.
When the sensor performance returns, theautomatic high beam system will resumeoperation.If the warning display does not disappearafter waiting for a while, there is a possibilitythat the sensor has a
malfunction. Contact an
authorized Mitsubishi Motors dealer forinspection of the sensor.
N00563201250
This function turns on the front side-markerand parking lights for approximately 30 sec-onds after the UNLOCK button on the remotecontrol transmitter is pressed when the com-bination headlights and dimmer switch is inthe “OFF” or “AUTO” position (vehiclesequipped with the automatic light control).The welcome light func
tion will operate only
when it is dark outside the vehicle.
N00547301181
This function turns on the headlights in thelow beam setting for approximately 30 sec-onds after the ignition switch is turned to the“OFF” or “LOCK” position or the operationmode is put in OFF.1. Turn the combination headlights and dim-mer switch to the “OFF” or “AUTO”
pped with the auto-
matic light control).2. Turn the ignition switch to the “OFF” or“LOCK” position or put the operationmode in OFF. Also, if a key was used tostart the engine, rem
ove the key from the
ignition switch.

Windshield is dirty

Welcome light
NOTE
While the welcome light function is operat-ing, perform one of
the following operations
to cancel the function.• Push the LOCK button on the remote con-trol transmitter.• Turn the combination headlights and dim-mer switch to the “ ” or “ ” position.• Turn the ignition switch to the “ON” posi-tion or put the operation mode in ON.
It is possible to modify functions as follows:• The headlights can be set to come on in thelow beam setting.• The welcome light f
unction can be deacti-
vated.
For details, consult a Mitsubishi Motorsdealer.On vehicles equipped with the SmartphoneLink Display Audio, sc
reen operations can
be used to make the adjustment.Refer to the separate owner’s manual fordetails.
Coming home light
NOTE
BK0249100US.book 215 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Wiper and washer switch
Features and controls 5-219
5
N00523001777
The windshield wiper
and washer can be
operated with the ignition switch or the oper-ation mode is in ON or ACC.If the blades are frozen to the windshield, donot operate the wipers
until the ice has melted
and the blades are free
d, otherwise the wiper
motor may be damaged.
NOTE
If the headlights are sw
itched to high beam,
the front fog lights will go out; they will illu-minate again when the headlights areswitched back to low beam.If the light switch is rotated to the “OFF” or“ ” position while the
front fog lights are
illuminated, they will automatically turn off.They can be turned back on again by rotatingthe combination headlights and dimmerswitch back to “ ” position, and turningthe knob in the direction of the “ON” posi-tion.Do not use fog lights ex
cept in conditions of
fog, otherwise excessive light glare maytemporarily blind oncoming vehicle drivers.
Wiper and washer switch
CAUTIONIf the washer is used
in cold weather, the
washer fluid sprayed against the glass mayfreeze, which may hinder visibility. Warmthe glass with the defroster before using thewasher.
Windshield wipers
NOTE
To ensure a clear rearward view, the rearwindow wiper will au
tomatically perform
several continuous opera
tions if the selector
lever is put in the “R” position while thewindshield wipers are operating.Refer to “Rear window wiper and washer”on page 5-223.
Except for vehicle with rain sensor MIST- Misting function
The wipers will operate once.
OFF- OffINT- Intermittent (Speed sensitive)HI- Fast
BK0249100US.book 219 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Wiper and washer switch5-220 Features and controls
5
With the lever in the “INT” (speed sensitiveintermittent operation) position, the intermit-tent intervals can be adjusted by turning theknob (A).
The misting function can be used when theignition switch or th
e operation mode is in
ON or ACC.The wipers will operate once if the wiperlever is raised to the “MIST” position andreleased. This operation
is useful when it is
drizzling, etc. The wi
pers will continue to
operate while the lever is held in the “MIST”
The windshield wipers can be operated withthe ignition switch or
the operation mode is in
ON or ACC.If the blades are frozen to the windshield orrear window, do not operate the wipers untilthe ice has melted and the blades are freed,otherwise the wiper mo
tor may be damaged.
To adjust intermittent intervals1- Fast2- Slow
NOTE
The speed-sensitive-
operation function of
the windshield wipers
can be deactivated.
For further information, please contact yourauthorized Mitsubishi Motors dealer or arepair facility of your
choice. On vehicles
equipped with the Sm
artphone Link Display
Audio, screen operati
ons can be used to
make the adjustment.Refer to separate owne
r’s manual for details.
Misting function
Vehicle with rain sensor MIST- Misting function
The wipers will operate once.
OFF- OffAUTO- Auto-wiper control
Rain sensorThe wipers will automaticallyoperate depending on the degree ofwetness on the windshield.
LO- SlowHI- Fast
BK0249100US.book 220 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Wiper and washer switch
Features and controls 5-221
5
Can only be used when
the ignition switch or
the operation mode is in ON.If the lever is put in
the “AUTO” position, the
rain sensor (A) will de
tect the extent of rain
(or snow, other moisture
, dust, etc.) and the
wipers will operate automatically.Keep the lever in the “OFF” position if thewindshield is dirty a
nd the weather is dry.
Wiper operation under th
ese conditions can
scratch the windshield and damage the wip-ers.
If your hands get trapped, you could sufferinjuries or the wipers
could malfunction. Be
sure to turn the ignition switch to the “OFF”mode in OFF, or move the lever to the “OFF”
the rain sensor.
Rain sensor
CAUTIONWith the ignition switch or the operationmode in ON and the lever in the “AUTO”
y automatically oper-
ate in the situati
ons described below.
• When cleaning the outside surface of thewindshield, if you touch the rain sensor.• When cleaning the outside surface of thewindshield, if you wipe with a cloth the rainsensor.• When using an automatic car wash.• A physical shock is applied to the wind-shield.• A physical shock is a
pplied to the rain sen-
sor.NOTE
To protect the rubber parts of the wipers, thisoperation of the wipers
does not take place
even if the lever is put in the “AUTO” posi-tion when the vehicle is
stationary and the
ambient temperature is approximately 32 °F(0 °C) or lower.Do not cover the sensor by affixing a stickeror label to the windshield. Also, do not putany water-repellent
coating on the wind-
shield. The rain sensor would not be able todetect the extent of rain, and the wipersmight stop working normally.CAUTION
In the following cases, the rain sensor maybe malfunctioning. Have
the vehicle checked
at an authorized Mitsubishi Motors dealer ora repair facility
of your choice.
• When the wipers operate
at a constant inter-
val despite changes in the extent of rain.• When the wipers do not operate eventhough it is raining.
The wipers may automatically operate whenthings such as insects
or foreign objects are
affixed to the windshield on top of the rainsensor or when the windshield is frozen.Objects affixed to th
e windshield
will stop
the wipers when the wipers cannot removethem. To operate the wipers again, move thelever to the “LO”
or “HI” position.
Also, the wipers may operate automaticallydue to strong direct s
unlight or electromag-
netic wave. To stop the wipers, move thelever to the “OFF” position.Contact an authoriz
ed Mitsubishi Motors
dealer or a repair fa
cility of your choice
when replacing th
e windshield glass.
NOTE
BK0249100US.book 221 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Wiper and washer switch5-222 Features and controls
5
With the lever in the “AUTO” position, it ispossible to adjust the sensitivity of the rainsensor by turning the knob (B).
Move the lever in the direction of the arrowand release, to opera
te the wipers once.
Use this function when you are driving inmist or drizzle.The wipers will operate once if the lever israised to the “MIST” position and releasedwhen the ignition switch or the operationmode is in ON or ACC.
The wipers will con-
tinue to operate while the lever is held in the“MIST” position.
The wipers will operate once if the lever ismoved to the “AUTO” position and the knob(C) is turned in the “+” direction when theignition switch or the operation mode is inON.
To adjust the sensitivity of the rain sensor“+”- Higher sensitivity to rain“-”- Lower sensitivity to rain
NOTE
Automatic wiper operation (rain sensitive)can be changed to in
termittent operation,
either vehicle speed se
nsitive or not vehicle
speed sensitive.For further information, please contact yourauthorized Mitsubishi Motors dealer or arepair facility of your choice.On vehicles equippe
d with the Smartphone
Link Display Audio, sc
reen operations can
be used to make the adjustment.Refer to the separate
owner’s manual for
details.
Misting function
BK0249100US.book 222 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Vehicle preparation before driving6-4 Driving safety
6
N00629001709
For a safer and more enjoyable trip, alwayscheck for the following:Before starting the vehicle, make certainthat you and all passengers are seated andwearing their seat
belts properly (with
children in the rear seat, in appropriaterestraints), and that all the doors and theliftgate are locked.
Move the driver’s seat as far backward aspossible, while keeping good visibility,and good control of the steering wheel,brakes, accelerator, and controls. Checkthe instrument panel indicators and multi-information display
for any possible prob-
lem.Similarly, the front
passenger seat should
also be moved as fa
r back as possible.
Make sure that infants and small childrenare properly restrained in accordance withall laws and
regulations.
Check these by selecting the defroster mode,and set the blower swit
ch on high. You should
be able to feel the air blowing against thewindshield. Refer to “Defrosti
ng or defogging (wind-
shield, door windows)” on page 7-12Check all the tires for heavy tread wear oruneven wear patterns. Look for stones, nails,glass, or other objects
stuck in the tread. Look
for any tread cuts or
sidewall cracks. Check
the wheel nuts for tightness, and the tires(including spare tire) for proper pressure.
Replace your tires before they are heavilyworn out.As your vehicle is equi
pped with a tire pres-
sure monitoring system, there is a risk ofdamage to the tire inflation pressure sensorswhen the tire is replaced on the rim. Tirereplacement should, onl
y, be performed by an
authorized Mitsubishi Motors dealer.Have someone watch wh
ile you turn all the
exterior lights on and off. Also check the turnsignal indicators and hi
gh-beam indicators on
the instrument panel.Check the ground under the vehicle afterparking overnight, for
fuel, water, oil, or
other leaks. Make sure
all the fluid levels are
correct. Also, if you
can smell fuel, you need
to find out why imme
diately and have it
fixed.
N00629201134
Even this vehicle’s sa
fety equipment, and
your safest driving, ca
nnot guarantee that you
can avoid an accident or injury. However, if
Vehicle preparation before driving Seat belts and seats
Defrosters Tires
Lights Fluid leaks Safe driving techniques
BK0249100US.book 4 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Dual-zone automatic climate
control air conditioner
7-6 Comfort controls
7
N00736901206
Press of the blower speed selectionswitch to increase the blower speed.Press of the blower speed selectionswitch to decrease the blower speed.The selected blower sp
eed will be shown in
the display (A).
9- Electric rear window
defogger switch
 P.5-225
10- OFF switch11- Driver’s side temperature display
 P.7-7
12- DUAL indicator13- Mode selection display14- Passenger’s side temperature display
 P.7-7
15- Air conditioning indicator16- Blower speed display
NOTE
There is an interior air temperature sensor(A) in the illustrated position.Never place anything ove
r the sensor, since
doing so will prevent it from functioningproperly.
NOTE
Since the air conditi
oning operation is con-
trolled while the ECO mode is operating,you may feel that effectiveness of the airconditioner is insufficient. ECO mode switch P.5-218
Even during ECO mode operation, you canselect normal operati
on of the air condi-
tioner.On vehicles equipped with the SmartphoneLink Display Audio, sc
reen operations can
be used to change the setting. Refer to theseparate owner’s manual for details.In extreme cold, the air conditioning controlpanel screen may ope
rate sluggishly. This
does not indicate a problem.It will disappear when the vehicle interiortemperature rises to a normal temperature.
Blower speed selection switch 1- Increase2- Decrease
BK0249100US.book 6 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Air cleaner filter9-10 Vehicle care and maintenance
9
3. Unclamp the cover. Open up the top of thecover and take out th
e air cleaner filter.
4. Replace the air cleane
r filter and put the
cover back on in its original position.
5. For 2.4 L models, put the duct back on inits original position.
2.4 L models
NOTE
Mitsubishi Motors Genuine Parts are recom-mended when replacing th
e air cleaner filter.
For 2.4 L models, make
sure that the connec-
tor is properly reconnected.After replacing the air cleaner filter, makesure that the hinges at the bottom of coverare firmly set.3.0 L models
CAUTIONTake care not to scra
tch the engine air flow
sensor when removing
the air cleaner cover.
2.4 L models3.0 L models
BK0249100US.book 10 ページ ２０１７年５月１０日　水曜日　午前８時４９分