2018 MITSUBISHI OUTLANDER III length

Automatic transaxle (if so equipped)
Features and controls 5-71
5
in the multi-information display while youare driving, there could be a malfunction inthe automatic transaxle.
N00514201425
This position locks the transaxle to preventthe vehicle from moving.
The engine can be
started in the “P” (PARK) position.Move the lever to this position only after thevehicle has come to a complete stop.At this position, the
transaxle is disengaged.
It is the same as th
e neutral position on a
manual transaxle and should be used whenthe vehicle is not moving for an extendedlength of time during driving, such as in atraffic jam.
CAUTIONIf a malfunction occurs in the automatictransaxle while driving, the warning dis-play or the warni
ng display will appear
on the information screen in the multi-infor-mation display. In this case, immediat
ely park your vehicle
in a safe place and fo
llow these procedures:
When warning display is showingThe automatic transaxle fluid is overheating.Stop your vehicle in a
safe place, put the
selector lever in the
“P” position, and open
the engine hood with the engine running toallow the engine to c
ool down. After a while,
confirm that the warning display is nolonger showing. It is safe to continue drivingif the display is no longer showing. If thewarning display remain
s, contact an autho-
rized Mitsubishi Motors
dealer or a repair
facility of your c
hoice immediately.
When warning display is showingIt may be that there is something unusualhappening in the automa
tic transaxle, caus-
ing a safety device to
activate. Have your
vehicle inspected by an
authorized Mitsubi-
shi Motors dealer or a
repair facility of your
choice immediately.
Selector lever positions

“P” PARK

“R” REVERSE

CAUTIONNever shift into the “P” (PARK) or “R”motion. If the lever is shifted into the “P”the vehicle is in moti
on, the transaxle may be
damaged.
“N” NEUTRAL

BK0249100US.book 71 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Continuously variable transmission (CVT) (if so equipped)
Features and controls 5-79
5
N00560601107
This position locks the transmission to pre-vent the vehicle from m
oving. The engine can
be started in the “P” (PARK) position.Move the lever to this position only after thevehicle has come to a complete stop.
At this position, the transmission is disen-gaged. It is the same
as the neutral position on
a manual transaxle and should be used whenthe vehicle is not m
oving for an extended
length of time during driving, such as in atraffic jam.
This position is used fo
r most city and high-
way driving. The transmission will automati-cally and continuously ch
ange its gear ratio
depending on road and driving conditions.Use when engine braking is needed, or forhigh-power sport drive.
After a while, confirm that the warningdisplay is no longer show
ing. It is safe to
continue driving if the display is no longershowing. If the warning display remains,contact an authorized Mitsubishi Motorsdealer or a repair facility of your choiceimmediately.[When warning di
splay is showing]
It may be that ther
e is something unusual
happening in the CVT, causing a safetydevice to activate
. Have your vehicle
inspected by an authorized MitsubishiMotors dealer or a repair facility of yourchoice immediately.
Selector lever positions

“P” PARK

“R” REVERSE

CAUTION
CAUTIONNever shift into the “P” (PARK) or “R”motion. If the lever is shifted into the “P”the vehicle is in motion, the transmissionmay be damaged.
“N” NEUTRAL

WA R N I N GNever move the selector lever to the “N”you could accidentally slip it into the “P”damaging the transmission.To prevent the vehicle from rolling whenstopped on a slope,
the engine should be
started in the “P” (PARK) position, not in“N” (NEUTRAL) position.
To prevent rolling, always keep your footon the brake pedal when the vehicle is in“N” (NEUTRAL) positi
on, or when shift-
ing into or out of

Blind Spot Warning (BSW) (with Lane Change Assist) (if so equipped)
5-126 Features and controls
5
N00592200040
The Blind Spot Warning (BSW) is a driving
aid system that alerts the driver when another
vehicle which may not be visible through the
outside rearview mirror is traveling in the
next lane behind your vehicle.
When a vehicle in the next lane is traveling at
same speed or faster in the detection areas,
the Blind Spot Warning light in the corre-
sponding outside rearview mirror will illumi-
nate. If the turn signal lever is operated to the
side where the Blind Spot Warning light is
illuminated, the Blind Spot Warning light will
blink and the system will beep three times to
alert the driver.
• Do not put anything including a sticker or
film to the outer side of the windshield in
front of or surrounding area of the sensor.
Also, do not put anything including a
sticker or film to the inner side of the wind-
shield under the sensor.• Do not attempt to deta ch or disassemble the
sensor.• If the windshield is misted, remove the mist from the windshield by using the defogger
switch.• Maintain the wiper blades in good condi- tion. Refer to “Wiper blades” on page 9-44.
When replacing the wiper blades, use only
Mitsubishi Motors Genuine parts or equiva-
lent.• Do not dirty or damage the sensor.• Do not spray glass cleaner on the sensor.Also, do not spill liquid, such as a bever-
age, to the sensor.• Do not install an elec tronic device, such as
antenna, or a device that emits strong elec-
tric waves, near the sensor.CAUTION
• Always use tires of the same size, same
type and same brand, and which have no
significant wear differences.• Do not modify the vehicle’s suspensions. If the windshield on the sensor or in the sur-
rounding area of the sensor is cracked or
scratched, the sensor may not detect an
object properly. This could cause a serious
accident. Turn off the FCM and have your
vehicle inspected as soon as possible at an
authorized Mitsubishi Motors dealer.
If you need to replace the windshield, con-
tact an authorized Mitsubishi Motors dealer. The sensor emits infrared rays when the
operation mode is in ON. Do not look into
the sensor by using optical goods such as a
magnifying glass. The infrared ray might
injure your eyes.Laser radar specifications

Laser classificationMax average power 45 mWPulse duration 33 nsWavelength905 nmDivergent angle
(horizon x vertical)28° x 12°
CAUTION
Laser classification labelBlind Spot Warning (BSW)
(with Lane Change Assist)
(if
so equipped)
BK0249100US.book 126 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Brake fluid
Vehicle care and maintenance 9-13
9
N00938701327
Check the fluid leve
l in the reservoir.
The fluid level must
be between the “MAX”
and “MIN” marks on the reservoir.The fluid level falls slightly with wear of thebrake pads, but this
does not indicate any
abnormality.If the fluid level falls sealed tight in a shortlength of time, it indi
cates leaks from the
brake system.If this occurs, have the vehicle checked by anauthorized Mitsubishi Motors dealer or arepair facility
of your choice.
Use the recommended brake fluid conform-ing to DOT 3 or DOT
4. The reservoir cap
must be tightly sealed to keep dirt and waterout.
N00939101940
The condition of the batte
ry is very important
for quick starting and to keep the vehicle’selectrical system work
ing properly. Check the
battery regularly.If battery performance is suspect, have thebattery and charging
system tested by an
authorized Mitsubishi Motors dealer or arepair facility
of your choice.
The electrolyte level
must be between the
limits shown on the outside of the battery. Fillit with distilled water as needed. The inside ofthe battery is divided into several compart-ments. Take the cap off of each compartmentand fill to the mark.
Brake fluid To check the fluid level
Fluid type
WA R N I N GTake care in handling brake fluid as it isharmful to the eyes, may irritates yourskin and will damage
painted surfaces.
Wipe up spills immediately.If brake fluid gets on your hands or inyour eyes, flush immediately with cleanwater. Follow up with a doctor as neces-sary.CAUTIONDo not let any petrol
eum-based fluid touch,
mix with, or get into
the brake fluid. This
will damage the seals.Be careful when handli
ng brake fluid. It can
damage painted surfaces.Use only the listed brak
e fluid. Different
brands of brake fluid
have different addi-
tives, and these can cause a chemical reac-tion. Do not mix brands of brake fluid.Keep the reservoir ta
nk cap closed to keep
the brake fluid from evaporating.
Battery
NOTE
After replacing the battery, the electroniccontrol system data for the automatic trans-axle, etc., will be erased.As a result, shifting may be rough.Shifting will become
smoother after several
changes in speed.
Checking battery electrolyte level
BK0249100US.book 13 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Vehicle dimensions11-4 Specifications
11
N01147501678
Vehicle dimensions Overall length
184.8 in (4,695 mm)
Overall width
71.3 in (1,810 mm)
Overall height
67.3 in (1,710 mm)
Wheel base
105.1 in (2,670 mm)
BK0249100US.book 4 ページ ２０１７年５月１０日　水曜日　午前８時４９分