2018 MITSUBISHI OUTLANDER III key

Power liftgate (if so equipped)5-42 Features and controls
5
The operation mode is in ON with theselector lever in the “P” (PARK) position,or the operation mode is in ACC or OFF.The power liftgate is completely open.Nothing is touching the auto reverse sen-sors on the power liftgate.
After unlocking the doors and the power lift-gate, the power liftgate can be operated bypressing the switch (A) of the F.A.S.T.-key orthe driver’s side power liftgate switch (B).
If the power liftgate switch is pressed twice ina row, the power liftgate operates after thewarning buzzer sounds and the hazard warn-ing flasher blinks.The power liftgate operates as follows:
If the power liftgate switch is pressed oncewhile the power liftgate is operating, thewarning buzzer sounds an
d the liftgate will
reverse and return to
the full open or closed
position.If the driver’s side power liftgate switch ispressed for more than 1 second, the powerliftgate will operate
after the buzzer sounds
and the hazard warning flasher blinks.The power liftgate operates as follows.
Operating the power liftgate using the F.A.S.T.-key or the driver’s side power liftgate switch

•While closed: The
warning buzzer sounds
and the power liftgate com-pletely opens.
•While open: The warning buzzer sounds
and the power liftgate com-pletely closes.
NOTE
If the power liftgate sw
itch is pressed 3 or
more times in a row, the power liftgate maynot operate normally.If this occurs, wait a short time before againpressing the power lift
gate switch twice.
•While closed: The warning buzzer sounds
and the power liftgate com-pletely opens.
•While open: The warning buzzer sounds
and the power liftgate com-pletely closes.
BK0249100US.book 42 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Power liftgate (if so equipped)Features and controls 5-43
5
If the driver’s side po
wer liftgate switch is
pressed once while the
power liftgate is oper-
ating, the warning buz
zer will sound and the
power liftgate will move in the directionopposite to the one in which it was operating.The power liftgate can
be opened by pressing
the open switch (C).If the open switch is pressed while the powerliftgate and all doors are unlocked, the power
liftgate will open after the warning buzzersounds and the hazard wa
rning flasher blinks.
The power liftgate can
be closed by pressing
the close switch (D) on the power liftgate.
If the close switch on the power liftgate ispressed, the power liftgate will close after thewarning buzzer sounds 3 times and the hazardwarning flasher
blinks 2 times.
If the close switch is pressed once while thepower liftgate is clos
ing, the warning buzzer
sounds once and the power liftgate opens.
N00576200026
If the auto reverse sensors (A) on either sideof the power liftgate de
tect that something is
being trapped by the cl
osing power liftgate,
the warning buzzer will sound once and theliftgate will automatically reverse directionand return to the full open position.
WA R N I N GWhen operating the
power liftgate, make
sure that there are no people near thepower liftgate and that there is sufficientspace behind and ab
ove the vehicle.
Opening the power liftgate using the open switch

NOTE
When you are carrying the F.A.S.T.-key withthe power liftgate is locked, the power lift-gate can be opened by pressing the openswitch even if the power liftgate is locked.For vehicles equipped w
ith the mirror retrac-
tor switch, the outside rearview mirrors auto-matically extend when the power liftgate andall doors are unlocked using the liftgate openswitch (C).
Closing the power liftgate using the close switch

NOTE
If the close switch is again pressed oncewhile the power liftgate is operating in theopening direction, th
e warning buzzer will
sound once and the power
liftgate will close.
Auto reverse

BK0249100US.book 43 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Theft-alarm system
Features and controls 5-47
5
N00510301226
Park the vehicle and st
op the engine. Arm the
system as described below.1. Except for vehicles equipped with theF.A.S.T.-key, remove the key from theignition switch.For vehicles equipped with the F.A.S.T.-key, put the operation mode in OFF.2. Make sure that the engine hood is closed.3. Lock all doors and the liftgate by usingthe keyless entry system or the F.A.S.T.-key operation.
At this time, the theft-alarm indicator (A)mation.4. The system has entered the armed stageafter about 20 seconds, when the theft-alarm indicator (A) flashing becomesslower.The theft-alarm indicator (A) continues toflash while the system is in the armedstage.
N00510401230
The alarm will be activated if any of the fol-lowing occur while the ve
hicle is parked and
the system is armed.One of the doors and the liftgate is openedwithout using the keyless entry system orthe F.A.S.T.-key operation.The engine hood is opened.
CAUTIONDo not modify or add parts to the theft-alarmsystem. Doing so could cause the theft-alarmto malfunction.
Armed stage Arm the system and leave
NOTE
If the engine hood is open, the theft-alarmindicator (A) illuminates and the system can-not enter the armed stage.The system enters the armed stage about 20seconds after the e
ngine hood is closed.
The system will be disarmed if, while thetheft-alarm indicator (A) is illuminated, alldoors and the liftgate are unlocked by usingthe keyless entry system or the F.A.S.T.-keyoperation.
The system will be disarmed if, while thetheft-alarm indicator is illuminated, the fol-lowing operation is performed.• Except for vehicles equipped with theF.A.S.T.-key, if the ignition switch is turnedto the “ON” position.• For vehicles equippe
d with the F.A.S.T.-
key, if the operation mode is put in ON.
The system will not be armed if a door, theliftgate or the engine
hood is not completely
closed. If this happens, rearm the system asdescribed above.The theft-alarm system can be activatedwhen people are riding inside the vehicle orwhen the windows are open. To prevent acci-dental activati
on of the alarm, do not set the
system to the system armed mode while peo-ple are riding in the vehicle.
Alarm stage
NOTE
BK0249100US.book 47 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Theft-alarm system5-48 Features and controls
5
N00582500040
When the alarm is activated:1. The headlights blink on and off for 3 min-utes.After 3 minutes the headlights automati-cally shut off.2. The horn will sound intermittently for 3minutes.
N00582600025
The alarm can be deacti
vated in the following
ways.By using the keyless entry system or theF.A.S.T.-key operation to lock or unlockthe doors and liftgate.Turn the ignition switch to the “ON” posi-tion or put the operation mode in ON.
N00510501202
The system will be disarmed if the followingoperation is performed.Except for vehicles equipped with theF.A.S.T.-key, if the ignition switch isturned to the “ON” position.For vehicles equipped with the F.A.S.T.-key, if the operation mode is put in ON.All doors and the lift
gate are unlocked by
using the keyless entry system or theF.A.S.T.-key operation.
Type of alarm
NOTE
The alarm will continue
to operate for 3 min-
utes. At the end of that
period, the alarm will
automatically shut off
to save battery power.
The system will then be rearmed until theproper disarming step is taken.The alarm will resu
me if unauthorized
actions are taken again, even if the alarm hasstopped.Horn sounds!Headlights blink on and off!
Alarm deactivation Disarmed stage
NOTE
If the UNLOCK button on the remote controltransmitter, or the driver’s or front passen-ger’s door lock/unlock switch is pressedwhen all doors and the li
ftgate are closed and
no door is opened with
in approximately 30
seconds, re-arming will
automatically occur.
The amount of time after unlocking until thevehicle relocks automatically can beadjusted. See an authorized MitsubishiMotors dealer for details.On a vehicle equipped with the SmartphoneLink Display Audio, the functions can beadjusted on the screen. For details, refer to aseparate owner’s manual.Once the system has been disarmed, it can-not be rearmed except
by repeating the arm-
ing procedure.Disarm...by using the keyless entry system or F.A.S.T.-key operation
BK0249100US.book 48 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Power window control
Features and controls 5-49
5
N00510601157
Use the following procedure to test the sys-tem:1. Lower the driver’s window.2. Arm the system as explained in “Armedstage”.comes on and flashe
s for approximately
20 seconds.4. Wait a few seconds and then unlock thedriver’s side door by using the inside doorlock knob. Open the door.5. Make sure that the horn sounds intermit-tently and the headlights blink when adoor is opened.6. Disarm the system by unlocking all doorsand the liftgate by using the keyless entrysystem or the F.A.S.T.-key operation.
N00510800383
Testing the theft-alarm system
Power window control 1- Open (down)2- Close (up)
NOTE
Never try to operate the main switch andsub-switch in different
directions at the same
time. This will free
ze the window in posi-
tion.Operating the power windows repeatedlywith the engine stoppe
d will run down the
battery. Use the window
switches only while
the engine is running.WA R N I N GBefore operating the power windows,make sure that nothing can be trapped(head, hands, fingers, etc.) in the window.
Never leave the vehicle without carryingthe key.Never leave children
or unreliable adults
unattended inside the vehicle.WA R N I N G
BK0249100US.book 49 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Parking brake
Features and controls 5-53
5
The sunshade can be opened or closed manu-ally while the sunroof is closed.
N00511401468
To park the vehicle, fi
rst bring it to a com-
plete stop, firmly apply the parking brake,and then move the selector lever to the “P”Make sure the brake warning light (red) isilluminated.
Sunshade

CAUTIONDo not attempt to close the sunshade whenthe sunroof is opened.Be careful that hands are not trapped whenclosing the sunshade.WA R N I N GDo not stick your head
, hands or anything
else in the su
nroof opening.
Before operating the sunroof, make surethat nothing can be trapped (head, hands,fingers, etc.).Never leave a child unr
eliable adults unat-
tended inside the vehicle.
NOTE
When leaving the vehicle unattended, besure to close the sunroof and carry the key.Do not try to operate the sunroof if it is fro-zen closed (after snowfall or during extremecold).Do not sit on or plac
e heavy luggage on the
sunroof or roof opening edge.Do not apply any forc
e that may cause dam-
age to the sunroof.Release the switch when the sunroof hasreached a completely open or completelyclosed position.If the sunroof does not operate when the sun-roof switch is operated, release the switchand check whether something is trapped bythe sunroof. If nothing is trapped, have thesunroof checked at an authorized MitsubishiMotors dealer.Be careful when tilting up the sunroof if a skicarrier or a roof carrie
r is installed. Depend-
ing on the model of ski carrier or roof carrier,the sunroof may contact
the carrier when the
sunroof is tilted up.Be sure to close the sunroof completelywhen washing the vehicle or when leavingthe vehicle.Do not put any wax on the weatherstrip(black rubber) around the sunroof opening. Ifit is waxed, the weat
herstrip cannot maintain
a weatherproof seal with the sunroof.After washing the vehicle or after rain besure to wipe off any water that is on the sun-roof before operating it.
Operating the sunroof repeatedly with theengine turned off will run down the battery.Operate the sunroof only while the engine isrunning.
Parking brake
NOTE
BK0249100US.book 53 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Outside rearview mirrors5-60 Features and controls
5
When the headlights of the vehicles behindyou are very bright, the reflection factor ofthe rearview mirror is automatically changedto reduce the glare.Normally, use the automatic mode. When theignition switch is turned to the “ON” positionor the operation mode is put in ON, the greenindicator (1) illuminates and the reflectionfactor of the mirror is automatically changed.
N00512201232
Adjust the outside rearview mirrors only aftermaking any seat adjustme
nts so as to have a
clear view to the rear of the vehicle.
Ty p e 3
NOTE
Do not hang items on,
or spray glass cleaner
on the sensor (2), as
reduced sensitivity
could result.If you want to stop automatic mode, pressthe switch (3) and the indicator will go off.To return to automatic mode, press theswitch again or perfor
m the following opera-
tion.[Except for vehicles e
quipped with the Free-
hand Advanced Secu
rity Transmitter
(F.A.S.T.-key)]Turn the ignition switch to the “ON” positionafter turning to “OFF” or “ACC” position.[For vehicles equipped with the Free-handAdvanced Security Transmitter (F.A.S.T.-key)]Put the operation mode
in ON after putting
the operation mode in OFF.
Outside rearview mirrors
WA R N I N GDo not attempt to adjust the outside rear-view mirrors while driving. This can bedangerous.Be sure to adjust the mirrors before driv-ing.
BK0249100US.book 60 ページ ２０１７年５月１７日　水曜日　午後２時３１分

Outside rearview mirrors5-62 Features and controls
5
With the ignition switch in the “ON” or“ACC” position or the
operation mode in ON
or ACC, push the mirror retractor switch toretract the mirrors. Push it again to extend themirrors to their original positions.After placing the ignition switch in the“LOCK” position or the operation mode inOFF, it is possible to
retract and extend the
mirrors using the mirror retractor switch forapproximately 30 seconds.
[Vehicles with the keyless entry system]The mirrors automatically retract or extendwhen the doors are locked or unlocked usingthe remote control switches of the keylessentry system.Refer to “Keyless entry system” on page 5-7.[Vehicles with the Free-hand Advanced Secu-rity Transmitter (F.A.S.T-key)]The mirrors automatically retract or extendwhen the doors are locked or unlocked usingthe remote control switches or the F.A.S.T-key.Refer to “Keyless entry system” on page 5-30or “To operate using the F.A.S.T.-key” onpage 5-15.
For vehicles equipped with the mirrorretractor switchRetracting and extending the mir-rors using the mirror retractor switch
CAUTIONIt is possible to retract and extend the mirrorsby hand. After retracti
ng a mirror using the
mirror retractor switch, however, you shouldextend it by using the switch again, not byhand. If you extended the mirror by handafter retracting it using
the switch, it would
not properly lock in pos
ition. As a result, it
could move because of the wind or vibrationwhile you are driving, taking away your rear-ward visibility.NOTE
Be careful not to get your hands trappedwhile a mirror is moving.If you move a mirror by hand or it movesafter hitting a person or object, you may notbe able to return it to its original positionusing the mirror retractor switch. If this hap-pens, push the mirror retractor switch toplace the mirror in its
retracted position and
then push the switch again to return the mir-ror to its original position.When freezing has occurred and mirrors failto operate as intended,
please refrain from
repeated pushing of the retractor switch asthis action can result in burn-out of the mir-ror motor circuits.
Retracting and extending the mir-rors without using the mirror retractor switch (automatic exten-sion function)
NOTE
Functions can be modified as stated below.Please consult an authorized MitsubishiMotors dealer.On vehicles equippe
d with the Smartphone
Link Display Audio, sc
reen operations can
be used to make the adjustment. Refer to theseparate owner’s
manual for details.
BK0249100US.book 62 ページ ２０１７年５月１０日　水曜日　午前８時４９分