2018 MERCEDES-BENZ CLA sensor

R
Alway se nsure tha ty ou onl ym ak et he kicking
movement withi nt he detection range of sen-
sors C .R
Stand at leas t12in( 30 cm )a wa yf rom the
rea ra re aw hile doing so.R
Do not come into contact with the bumper
whil em ak ing the kicking movement. Other-
wise, the sensors ma yn ot functio nc orrectly.R
HANDS-FREE ACCESS does not functio nd ur -
ing engine start. R
Dirt caused by roa ds al ta round sensors C
ma yr estrict functionality.
Using the HANDS-FREE ACCESS with ap ros-
theti cl eg ma yr estrict functionality.R
If aK EYLESS-GO key is withi nt he rea rd et ec-
tio nr an ge of KEYLESS-GO ,H ANDS-FREE
ACCESS could be triggered .T he trun kl id
could thu sbeo pe ne du nintentionally, for
example, when you: -
set something down or lift something up
behind the vehicle. -
polish the rea roft he vehicle.
Do not carry the KEYLESS-GO key abou ty ou r
perso nint hes es it uations or in situations sim-
ilar to these. Thi sw il lp revent the uninten-
tional opening of the trun kl id . Operation X
To open: kick into sensor detection range C
belo wt he bumpe rw it hy ou rf oot.X
If the trunk li dd oe sn ot ope na fte rs ever al
attempts: wait at leas tt en second st hen
move your le gu nder the bumpe ro nce again.
If yo uh ol dy ou rf oo tu nder the bumpe rf or too
long, the trun kl id does not open. Repeat the leg
movement more quickl yift hi so ccurs.
Opening automaticall yf rom inside
Important safety notes
G WARNING
Combustion engine se mi tp oiso nou se xhaust
gases such as carbo nm onoxide. Exhaust
gases can ente rt he vehicl ei nterio rift he
trun kl id is open when the engine is running,
especially if the vehicl eisinm otion. There is a
ris kofp oiso ning.
Alway ss wi tch off the engine before opening
the trun kl id .N ever drive with the trun kl id
open.
! The trun kl id swing su pwar ds when opened.
Therefore ,m ak es ur et ha tt her eiss uf ficient
clearance above the trun kl id .
The opening dimensions of the trun kl id can be
found under "Vehicle data" ( Y
page 320).
Opening
Yo uc an open the trun kl id from the driver's seat
when the vehicl eiss tationar ya nd unlocked.80
Trunk
Opening and closing

On vehicles with ap anorama roof with power
tilt/sliding panel: X
Press and hold the 7 button agai nu ntil the
roller sunblind of the panorama roof with
power tilt/sliding panel closes. X
To interrup tc onvenienc ec losing: release
the 7 button.
Using KEYLESS-GO The driver's door and the door at which the han-
dle is used, must both be closed. The SmartKey
must be outside the vehicle. The gap between
the SmartKey and the corresponding door han-
dle should not be greater than 3ft(1m ).
X
Touch recessed sensor surface C on the
door handle until the side windows and the
panorama roof with power tilt/sliding panel
are fully closed.
i Make sure you only touch recessed sensor
surface C .X
Make sure that all the side windows are
closed. X
Make sure that all the side windows and the
panorama roof with power tilt/sliding panel
are closed. On vehicles with ap anorama roof with power
tilt/sliding panel: X
Touch recessed sensor surface C on the
door handle agai nu ntil the roller sunblind of
the panorama roof with power tilt/sliding
panel closes. X
To interrup tc onvenienc ec losing: release
recessed sensor surface C on the door han-
dle.
Resetting the side windows If as ide window can no longer be closed fully,
you must reset it. X
Close all the doors. X
Turn the SmartKey to position G or H in the
ignition lock ( Y
page 122). X
Pull the corresponding switch on the door
control panel until the side window is com-
pletely closed ( Y
page 82).X
Hold the switch for an additional second.
If the side window opens agai ns lightly:X
Immediately pull the corresponding switch on
the door control panel until the side window is
completely closed ( Y
page 82).X
Hold the switch for an additional second. X
If the respective side window remains closed
after the button is released ,t hen it has been
set correctly. If this is not the case, repeat the
steps above.
Problems with the side windows
G WARNING
If you close as ide window agai ni mmediately after it has been blocked or reset, the side window
closes with increased or maximum force. The reversing feature is then not active. Parts of the
body could be trapped in the closing area in the process. This poses an increased risk of injury or
even fatal injury.
Make sure that no parts of the body are in the closing area. To stop the closing process, release
the switch or push the switch agai ntor eopen the side window.84
Side windows
Opening and closing

If contact is made with ar oof carrier approved
by Mercedes-Benz, the sliding sunroof lowers
slightly but remains raise datt he rear.
Rain-closing feature The rain-closing feature is only available for vehi-
cles with ar ain sensor.
When the SmartKey is in position Z in the igni-
tion lock or is removed, the sliding sunroof
closes automatically: R
if it starts to rain. R
at extreme outsid et emperatures.R
after six hours. R
if there is am alfunction in the powe rs upply.
The panorama roof with powe rt ilt/sliding panel
remains raise datt he rear in order to allow ven-
tilation of the vehicle interior.
If the panorama roof with powe rt ilt/sliding
panel is obstructed whil eb eing closed by the
rain-closing feature, it opens again slightly. The
rain-closing feature is then deactivated.
The panorama roof with powe rt ilt/sliding panel
does not close if: R
it is raise datt he rear.R
it is blocked. R
no rain is falling on the area of the windshield
being monitored by the rain sensor. If the
vehicle ,f or example ,isu nder ab ridge or in a
carport, the field of the sensor may be cov-
ered.
Operating the rolle rs unblind for the
panorama roof with powe rt ilt/sliding
panel
Important safety notes
G WARNING
Parts of the body could become trapped
betwee nt he rolle rs unblind and frame or slid-
ing sunroof during automatic opening or clos-
ing. There is ar isk of injury.
When opening or closing, make sure that no
body parts are in the sweep of the rolle rs un-
blind. If somebod yb ecomes trapped: R
release the switch immediately ,o rR
during automatic operation, push the
switch briefl yina ny direction
The opening or closing procedure wil lbes top-
ped.
The rolle rs unblind shields the vehicle interior
from sunlight. The rolle rs unblind can only be
opened and closed when the panorama roof
with powe rt ilt/sliding panel is closed.
Rolle rs unblind reversin gf eatureThe rolle rs unblind is equipped with an auto-
matic reversing feature. If as olid object blocks
or restricts the rolle rs unblind during the closing
process, the rolle rs unblind opens again auto-
matically. The automatic reversing feature is
only an aid and is not as ubstitute for you ra tten-
tiveness when closing the rolle rs unblind.
G WARNING
The reversing feature does not react: R
to soft, ligh ta nd thin objects, e.g. small fin-
gers R
when closing the rolle rs unblind again man-
ually immediately after automatic reversal
This means that the reversing feature cannot
prevent someone being trapped in these sit-
uations. There is ar isk of injury.
When closing the rolle rs unblind, make sure
that no body parts are in the sweep area.
If somebod yb ecomes trapped: R
release the switch immediately ,o rR
press the switch in any direction during the
automatic closing process
The closing process is stopped.Panorama roof with powe rt ilt/sliding panel 87
Opening and closing Z

Exterio rl ighting
General notes For reason sofs afety, Mercedes-Ben zr ecom-
mends that you driv ew ith th el ight ss witched on
even durin gt he daytime. In som ec ountries,
operatio noft he headlamps varies due to legal
requirement sa nd self-impose do bligations.
Settin gt he exterio rl ighting
Settin go ptionsExterior lighting can be set usin gt he :R
light switch R
combinatio ns witch ( Y
page 101)R
on-board compute r( Y
page 187)
Light switch
Operation
G c
Left-han ds ta nding lampsH d
Right-hand standing lampsI `
Parking lamps ,l icens ep lat ea nd
instrumen tc luste rl ightingJ X
Automatic headlam pm ode, controlled
by th el ight sensor
K X
Low-beam/high-beam headlamps

i When you switch off the engine, the last
speed stored is cleared.
Distance Pilot DISTRONIC
General notes Distance Pilot DISTRONIC regulates the speed
and automatically helps you maintain the dis-
tanc etot he vehicle detected in front. Vehicles
are detected with the aid of the radar sensor
system. Distance Pilot DISTRONIC brakes auto-
matically to avoid exceedin gt he set speed or to
maintain the designated distanc ef rom the vehi-
cle in front.
If Distance Pilot DISTRONIC detect st hat there is
ar isk of ac ollision, you will be warned visually
and acoustically. Without your intervention, Dis-
tanc eP ilot DISTRONIC cannot prevent ac olli-
sion. An intermittent warning ton ew ill then
sound and the distanc ew arning lamp will light
up in the instrument cluster. Brake immediately
in order to increase the distanc etot he vehicle in
fron tort ake evasive action provided it is safe to
do so.
Distance Pilot DISTRONIC operates in the range
between 0m ph (0 km/h) and 120 mph
(200 km/h).
Change into al ower gear in good time on long
and steep downhill gradients .T his is especially
importan tift he vehicle is laden. By doing so, you
will make use of the braking effect of the engine.
This relieves the load on the brake system and
prevent st he brakes from overheatin ga nd wear-
ing too quickly.
Do not use Distance Pilot DISTRONIC on roads
with steep gradients.
For Distance Pilot DISTRONIC to assist you
when driving, the radar sensor system must be
operational.
Sinc eD istance Pilot DISTRONIC transmits radar
waves, it can resemble the radar detectors of
the responsible authorities. You can refer to the
relevant chapter in the Operator' sM anual if
questions are asked about this.
i USA only: This device has been approved by
the FCC as a" Vehicular Radar System". The
radar sensor is intended for use in an auto-
motive radar system only. Removal, tamper-
ing, or altering of the device will void any war-
ranties, and is not permitted by the FCC. Do not tamper with, alter, or use in any non-
approved way.
An yu nauthorized modification to this device
could void the user's authority to operate the
equipment.
i Canada only: This device complies with
RSS-210 of Industry Canada. Operation is
subject to the following two conditions:
1. This device may not cause interference,
and
2. This device must accept any interference
received, including interference that may
cause undesired operation of the device.
Removal, tampering, or altering of the device
will void any warranties, and is not permitted.
Do not tamper with, alter, or use in any non-
approved way.
An yu nauthorized modification to this device
could void the user's authority to operate the
equipment.
Important safety notes
G WARNING
Distance Pilot DISTRONIC does not react to: R
people or animals R
stationary object sont he road, e.g. stopped
or parked vehicles R
oncoming vehicles and crossin gt raffic
As ar esult, Distance Pilot DISTRONIC may
neither give warnings nor intervene in such
situations. There is ar isk of an accident.
Always pay careful attention to the traffic sit-
uation and be ready to brake.
G WARNING
Distance Pilot DISTRONIC cannot always
clearly identif yo ther road users and complex
traffic situations.
In such cases, Distance Pilot DISTRONIC may: R
give an unnecessary warning and then
brake the vehicle R
neither give aw arning nor intervene R
accelerat eorb rake unexpectedly
There is ar isk of an accident.Driving systems 151
Driving and parking Z

Selecting Sport mode The firmer settin goft he suspension tuning in
the Sport drive program ensures even better
contact with the road. Select this drive program
when employing as porty driving style, e.g. on
winding countr yr oads.X
Press DYNAMI CS ELECT button ( Y
page 128)
as many times as necessary until the Sport
drive program is selected.
Parking Assist PARKTRONIC
Important safety notes Parking Assist PARKTRONIC is an electronic
parking aid with ultrasound. It monitor st he area
around your vehicle using six sensors in the
front bumper and six sensors in the rear
bumper. Parking Assist PARKTRONIC visually
and audibly indicates the distance between your
vehicle and an object.
Parking Assist PARKTRONIC is only an aid. It is
not ar eplacement for your attention to your
immediate surroundings. You are always
responsible for safe maneuvering, parking and
exiting ap arking space. Make sure that there
are no persons, animals or object sint he maneu-
vering area while maneuvering and parking in/
leaving parking spaces.
! When parking, pay particular attention to
object sa bove or below the sensors, such as
flower pots or trailer drawbars. Parking Assist
PARKTRONIC does not detect such objects
when they are in the immediate vicinity of the
vehicle. You could damage the vehicle or the
objects.
The sensors may not detect snow and other
object st hat absorb ultrasonic waves.
Ultrasonic sources such as an automatic car
wash, the compressed-air brakes of at ruck or
ap neumatic drill could cause Parking Assist
PARKTRONIC to malfunction.
Parking Assist PARKTRONIC may not function
correctly on uneven terrain.
Parking Assist PARKTRONIC is activated auto-
matically when you: R
switch on the ignition R
shift the transmission to position [ , ^ or
\\ R
release the electric parking brake Parking Assist PARKTRONIC is deactivated at
speeds above 11 mph (18 km/h). It is reactiva-
ted at lower speeds.
Range of the sensors General notes Parking Assist PARKTRONIC does not take into
account obstacles located: R
below the detection range, e.g. people, ani-
mals or objects. R
above the detection range, e.g. overhanging
loads, tail section sorl oading ramps of trucks.
C
Sensors in the front bumper, left-hand side
(example)
The sensors must be free from dirt, ice or slush.
They can otherwise not function correctly. Clean
the sensors regularly ,t aking care not to scratch
or damage them ( Y
page 265).Driving systems 161
Driving and parking Z

Range
C
Detection rang eoff ront sensorsD
Detection rang eofr ea rs ensors
Front sensors
Center Approx. 40 in (approx.
100 cm)
Corners Approx. 24 in (approx.
60 cm)
Rear sensors
Center Approx. 48 in (approx.
120 cm)
Corners Approx. 32 in (approx.
80 cm)
Minimum distance
Center Approx. 8i n( ap prox. 20 cm)
Corners Approx. 6i n( ap prox. 15 cm)
If there is an obstacl ew it hin this range, the rel-
evant warning display sl ig ht up and aw ar ning
tone sounds. If the distance falls below the min-
imum, the distance may no longer be shown. Warning displays
C
Segments on the left-hand sid eoft he vehi-
cle D
Segments on the right-hand sid eoft he vehi-
cle

Any unauthorized modification to thi sd ev ice
could voi dt he user’ sa ut hority to operate the
equipment.
Radar sensors The rada rs ensors for Blind Spo tA ssist ar ei nte-
grated into the rea rb um per. Make sure tha tt he
bumpers ar ef re ef rom dirt, ice or slush. The
sensors must not be covered ,f or exampl eb y
cycle racks or overhanging loads. Following a
severe impact or in the event of damage to the
bumpers, have the functio noft he rada rs ensors
checked at aq uali fied specialist workshop.
Blind Spo tA ssist ma ynol on ge rw or kp roperly.
Monitorin gr ang eoft he sensorsIn particular, the detection of obstacle sc an be
impaired if: R
ther eisd ir tont he sensors or anything else
covering the sensors R
ther eisp oo rv isibility ,e .g .d ue to fog ,h eavy
rain or snow R
an arrow vehicl et raveling in front, e.g .a
motorbike or bicycle R
the roa dh as ver yw id el an esR
the roa dh as narrow lanesR
yo ua re not driving in the middl eoft he laneR
ther ea re barriers or othe rr oa db ou ndaries
Vehicles in the monitoring range ar et hen not
indicated.
Blind Spo tA ssist monitors the area up to 10 ft
(3 m) behind your vehicl ea nd directl yn ext to it.
If the lanes ar en arrow ,v ehicles driving in the
lane beyond the lane next to your vehicl em a y be
indicated ,e specially if the vehicles ar en ot driv-
ing in the middl eoft hei rl an e. Thi sm ay be the
cas eift he vehicles ar ed riving on the inne rs id e
of thei rl an e.
Due to the nature of the system: R
warning sm ay be issued in error when driving
close to crash barriers or similar solid lane
borders. R
warning sm ay be interrupte dw he ny ou are
driving alongsid ep ar ticularly long vehicles,
such as trucks, for ap rolonge dt ime. Warning display
C
Warning display
Blind Spo tA ssist is not active at speed sb elow
approximatel y20m ph (30 km/h). Vehicles in
the monitoring range ar et hen not indicated.
Whe nB lind Spo tA ssist is activated ,i ndicator
lamp C in the exterio rm irrors lights up yellow
at speed sofupto20m ph (30 km/h). At speeds
above 20 mph (30 km/h), the indicator lamp
goe so ut and Blind Spo tA ssist is operational.
If av ehicl eisd et ecte dw it hi nt he blind spot
monitoring range at speed sa bo ve 20 mph
(30 km/h), warning lamp C on the correspond-
ing side lights up red .T hi sw ar ning is always
emitted when av ehicl ee nters the blind spot
monitoring range from behind or from the side.
Whe ny ou overtake av ehicle, the warning only
occurs if the difference in speed is less than
7m ph (12 km/h).
The yellow indicator lamp goe so ut if reverse
gear is engaged .Int hi se vent, Blind Spo tA ssist
is no longe ra ctive.
The brightness of the indicator/warning lamps
is adjusted automaticall ya ccording to the ambi-
ent light.
Collisio nw ar ning
If av ehicl eisd et ecte dint he monitoring range of
Blind Spo tA ssist and yo us wi tch on the corre-
sponding turn signal, ad ouble warning tone
sounds. Re dw ar ning lamp C flashes. If the turn
signa lr emains on, vehi cles detecte da re i ndica-
ted by the flashing of red warning lamp C .
There ar enof ur the rw ar ning tones.Driving systems 173
Driving an dp arking Z