2018 LEXUS NX300h light

282 5-4. Using the storage features
LEXUS NX300h Owners Manu-
al_USA_OM78212U 1 Open (press the button)
2 Unlock with the mechanical key
3 Lock with the mechanical key ■
Glove box light
The glove box light turns on when the tail
lights are on.
1 Lift the lid while pushing the button
to release the lock. 2 Vehicles with wireless charger: Lift
the wireless charger.
■
Console box tray (vehicles without wire-
less charger) ●
The tray slides forward/backward and
can be removed.
■
Console box light
The console box light turns on when the tail
lights are on.
■
Cup holders 
FrontGlove box
Console box
Cup holders/bottle holders

288 5-5. Using the other interior features
LEXUS NX300h Owners Manu-
al_USA_OM78212U 5-5.Using the other interior features
1 To set the visor in the forward posi-
tion, flip it down.
2 To set the visor in the side position,
flip down, unhook, and swing it to
the side.
3 To use the side extender, place the
visor in the side position, then slide
it backward. ■
Sun visors
Slide the cover to open. The light turns on when the cover is
opened.
■
Sunglass holder
Remove the lid of sunglasses holder using the strap . ( → P.283)There is a vanity mirror on the back side of
the lid.
■
Automatic lights off to prevent 12-volt
battery discharge
If the vanity lights remain on when the
power switch is turned off, the lights will go
off automatically after 20 minutes.
The GPS clock’s time is automatically
adjusted by utilizing GPS time infor-
mation.
For details, refer to the “NAVIGA-
TION AND MULTIMEDIA SYSTEM
OWNER’S MANUAL”.Other interior features
Sun visors
Vanity mirrors NOTICE■
To prevent damage to the vanity mir-
ror
When the lid of sunglass holder is
removed, do not subject it to strong
impacts or set heavy objects on top of it. ■
To prevent 12-volt battery discharge
Do not leave the lights on longer than
necessary when the hy brid system is off.
Clock A

2915-5. Using the other interior features
LEXUS NX300h Owners Manu-
al_USA_OM78212U 5
Interior features ■
Name for all parts
Power supply switch
Operation indicator light
Charge area ■
Using the wireless charger
1 Open the console box. ( → P.282)
2 Press the power supply switch of
the wireless charger.Switches on and off with each press of the
power supply switch.
When turned on, the operation indicator
light (green) comes on.
Even with the hybrid system off, the on/off
state of the power supp ly switch is memo-
rized. 3 Place the charging side of the por-
table device down. When charging, the operation indicator
light (orange) comes on.
If charging is not occurring, try placing the
portable device as close to the center of
the charging area as possible.
When charging is complete, the operation
indicator light (green) comes on.
 Recharging function
• When charging is complete and
after a fixed time in the charge sus-
pension state, ch arging restarts.
• When the portable device is moved,
charging is stopped for a moment
and then it restarts.A
B
C

292 5-5. Using the other interior features
LEXUS NX300h Owners Manu-
al_USA_OM78212U ■
Lighting conditions of operation
indicator light
*
: Depending on the portable device, there
are cases where the operation indicator
light will continue being lit up orange
even after the char ging is complete.
 When the operation indicator light
flashes When an error occurs , the operation indi-
cator light flashes an orange color. Handle
the error based on the following tables.
• Flashing repeatedly once every second
(Orange)
• Repeatedly flashes 3 times continuously
(Orange) • Repeatedly flashes 4 times continuously
(Orange)
■
The wireless charger can be operated
when
The power switch is in ACCESSORY or
ON mode. ■
Usable portable devices ●
Qi standard wireless charge standard
can be used on compatible devices.
However, not all Qi standard devices and
compatibility ar e guaranteed.●
Starting with mobile phones and smart
phones, it is aimed for low power electri-
cally supplied portable devices of no
more than 5W.
■
When covers and accessories are
attached to po rtable devices
Do not charge in situations where cover
and accessories not able to handle Qi are
attached to the portable device. Depending
on the type of cover and accessory, it may
not be possible to charge. When charging is
not performed even with the portable
device placed on the charge area, remove
the cover and accessories.Operation
indicator
light Conditions
Turning off When the Wireless charger
power supply is off
Green
(comes on) On Standby (charging pos-
sible state)
When charging is complete *
Orange
(comes on) When placing the portable
device on the charging area
(detecting the portable
device)
Charging
Suspected causes Handling method
Vehicle to charger
communication fail-
ure. Contact your Lexus
dealer. Suspected causes Handling method
A foreign substance
is between the por-
table device and
charge area. Remove the foreign
substance from
between portable
device and the
charge area.
The portable device
is out of sync due to
the device being
shifted from the cen-
ter of the charge
area. Place the portable
device near the cen-
ter of the charge
area.
Suspected causes Handling method
Temperature rising
within the wireless
charger. Stop charging at
once and start
charging again after
for a while.

2935-5. Using the other interior features
LEXUS NX300h Owners Manu-
al_USA_OM78212U 5
Interior features ■
While charging, noise enters the AM
radio
Turn off the wireless charger and confirm
that the noise has decreased. If the noise
decreases, continuously pushing the power
supply switch of the wireless charger for 2
seconds, the frequency of the charger can
be changed and the noise can be reduced.
Also, on that occasion, the operation indi-
cator light will flash orange 2 times. ■
Important points of the wireless charger●
If the electronic key cannot be detected
within the vehicle interior, charging can-
not be done. When the door is opened
and closed, charging may be temporarily
suspended.●
When charging, the wireless charging
device and portable device will get
warmer, however this is not a malfunction.
When a portable device gets warm while
charging, charging may stop due to the protection function on the portable
device side. In this case, when the tem-
perature of the port able device drops
significantly, charge again. ■
Operation sounds
When the power supply is turned on, while
searching for the portable device a sound
will be produced, however this is not a mal-
function. ■
Certification for the wireless charger
FCC Note: This equipment has been tested
and found to comply with Part 18 of the
FCC Rules. These limits are designed to
provide reasonable protection against
harmful interference in a residential installa-
tion.
FCC Caution: Any changes or modifica-
tions not expressly approved by the party
responsible for compliance could void the
user’s authority to operate this equipment.

298 5-5. Using the other interior features
LEXUS NX300h Owners Manu-
al_USA_OM78212U *
:If equipped
The HomeLink ®
wireless control sys-
tem in your vehicle has 3 buttons which
can be programmed to operate 3 dif-
ferent devices. Refer to the program-
ming methods on the following pages
to determine the method which is
appropriate for the device. HomeLink ®
indicator light
Garage door operation indicators
Buttons ■
Codes stored in the HomeLink ®
mem-
ory ●
The registered codes are not erased even
if the battery cable is disconnected.●
If learning failed when registering a dif-
ferent code to a HomeLink ®
button that
already has a code registered to it, the
already registered code will not be
erased.■
Certification for the garage door opener 
For vehicles sold in the U.S.A.Garage door opener *
The garage door opener can be
programmed using the Home-
Link ®
to operate garage doors,
gates, entry doors, door locks,
home lighting systems, security sys-
tems, and other devices.
System components A
B
C

300 5-5. Using the other interior features
LEXUS NX300h Owners Manu-
al_USA_OM78212U within 60 seconds, otherwise the indi-
cator light will stop flashing and pro-
gramming will not be able to be
completed.
1 Press and release the HomeLink ®

button you want to program and
check that the HomeLink ®
indica-
tor light flashes orange.
2 Point the remote control transmit-
ter for the device at the rear view
mirror, 1 to 3 in. (25 to 75 mm)
from the HomeLink ®
buttons.Keep the HomeLink ®
indicator light in
view while programming.
3 Program a device.

Programming a device other than
an entry gate (for U.S.A. owners) Press and hold the remote control trans-
mitter button until the HomeLink ®
indica-
tor light changes from slowly flashing
orange to rapidly flashing green (rolling
code) or continuously lit green (fixed
code), then release the button. 
Programming an entry gate (for
U.S.A. owners)/Programming a
device in the Canadian market Press and release the remote control trans-
mitter button at 2 second intervals, repeat-
edly, until the HomeLink ®
indicator light
changes from slowly flashing orange to
rapidly flashing green (rolling code) or
continuously lit green (fixed code).
4 Test the HomeLink ®
operation by
pressing the newly programmed
button and observing the indicator
light:
 Indicator light illuminates: Program-
ming of a fixed code device has
completed. The garage door or
other device should operate when a
HomeLink ®
button is pressed and
released.
 Indicator light flashes rapidly: The
garage door opener motor or other
device is equipped with a rolling
code. To complete programming,
firmly press and hold the Home-
Link ®
button for 2 seconds then
release it.
 If the garage door or other device
does not operate, proceed to “Pro-
gramming a rolling code system”.

3015-5. Using the other interior features
LEXUS NX300h Owners Manu-
al_USA_OM78212U 5
Interior features 5 Repeat the steps above to program
another device for any of the
remaining HomeLink ®
buttons.■
Programming a rolling code sys-
tem
2 or more people may be necessary to
complete rolling code programming.
1 Locate the “Learn” or “Smart” but-
ton on the garage door opener
motor in the garage.This button can usuall y be found where the
hanging antenna wire is attached to the
unit. The name and color of the button may
vary by manufacturer. Refer to the Owner’s
manual supplied with the garage door
opener motor for details.
2 Press and release the “Learn” or
“Smart” button.
Perform 3 within 30 seconds after
performing 2 .
3 Press and hold the desired Home-
Link ®
button (inside the vehicle) for 2 seconds and release it. Repeat
this sequence (press/hold/release)
up to 3 times to complete pro-
gramming.
If the garage door opener motor
operates when the HomeLink ®

button is pressed, the garage door
opener motor recognizes the
HomeLink ®
signal.
■
Enabling 2-way communication
with a garage door (only available
for compatible devices)
When enabled, 2-way communication
allows you to check the status of the
opening and closing of a garage door
through indicators in your vehicle.
2-way communication is only available
if the garage door opener motor used
is a compatible device. (To check
device compatibility, refer to
www.HomeLink.com.)
1 Within 5 seconds after program-
ming the garage door opener has
been completed, if the garage door
opener motor is trained to Home-
Link ®
, both garage door operation
indicators will flash rapidly green
and the light on the garage door
opener motor will blink twice, indi-