2018 Lexus LC500 steering

160
-$@-$I@0.@0.&@ &&

4-1. Before driving
NOTICE
●When driving over bumps in the road, drive as slowly as possible to avoid damaging the wheels, underside of the
vehicle, etc.
■If you get a flat tire while driving
A flat or damaged tire may cause the fol-
lowing situations. Hold the steering wheel firmly and gradually depress the brake pedal to slow down the vehicle.
●It may be difficult to control your vehi-
cle.
●The vehicle will make abnormal sounds or vibrations.
●The vehicle will lean abnormally.
Information on what to do in case of a flat tire ( P.384)
■When encountering flooded roads
Do not drive on a road that has flooded after heavy rain etc. Doing so may cause the following serious damage to the vehi-
cle:
●Engine stalling
●Short in electrical components
●Engine damage caused by water immersion
In the event that you drive on a flooded road and the vehicle is flooded, be sure
to have any authorized Lexus retailer or Lexus authorized repairer, or any reliable repairer check the following:
●Brake function
●Changes in quantity and quality of oil
and fluid used for the engine, transmis- sion, differentials, etc.
●Lubricant condition for the propeller shaft, bearings and suspension joints
(where possible), and the function of all joints, bearings, etc.
If the shift control system is damaged by flooding, it may not be possible to shift
the shift position to P, or from P to other positions. In this case, contact any autho-rized Lexus retailer or Lexus authorized
repairer, or any reliable repairer immedi- ately.
■When parking the vehicle
Always set the parking brake, and shift the shift position to P. Failure to do so may cause the vehicle to move or the
vehicle may accelerate suddenly if the accelerator pedal is accidentally depressed.

161
4
-$@-$I@0.@0.&@ &&

4-1. Before driving
Driving
Cargo and luggage
Take notice of the following infor-
mation about storage precautions,
cargo capacity and load:
WARNING
■Things that must not be carried in the trunk
The following things may cause a fire if loaded in the trunk:
●Receptacles containing gasoline
●Aerosol cans
■Storage precautions
Observe the following precautions. Failure to do so may prevent the pedals from being depressed properly, may
block the driver’s vision, or may result in items hitting the driver or passengers, possibly causing an accident.
●Stow cargo and luggage in the trunk
whenever possible.
●Do not place cargo or luggage in or on the following locations.
• At the feet of the driver
• On the front passenger or rear seats
(when stacking items)
• On the package tray
• On the instrument panel
• On the dashboard
• In front of Center Display
●Secure all items in the occupant com-
partment.
■Load and distribution
●Do not overload your vehicle.
●Do not apply loads unevenly. Improper loading may cause deterio-
ration of steering or braking control which may cause death or serious injury.

164
-$@-$I@0.@0.&@ &&

4-2. Driving procedures
■Electronic key battery depletion
 P.112
■Conditions affecting operation
 P.124
■Notes for the entry function
 P.124
■Steering lock function
●After turning the engine switch off and
opening and closing the doors, the steer- ing wheel will be locked due to the steer-ing lock function. Op erating the engine
switch again automatically cancels the steering lock.
●When the steering lock cannot be released, “Push engine switch while turn-ing the steering wheel in either direction”
will be displayed on the multi-information display. Press the engine switch shortly and firmly
while turning the steering wheel left and right.
●To prevent the steering lock motor from overheating, operation of the motor may
be suspended if the engine is turned on and off repeatedly in a short period of time. In this case, refrain from operating
the engine switch. After about 10 sec- onds, the steering lock motor will resume functioning.
■If there is a malfunction in the smart
entry & start system
If “Entry & Start System Malfunction” is dis-
played on the multi-information display, the system may be malfunctioning. Have the vehicle inspected by any authorized Lexus
retailer or Lexus authorized repairer, or any reliable repairer immediately.
■Electronic key battery
 P.349
■Operation of the engine switch
●If the switch is not pressed shortly and firmly, the engine switch mode may not
change or the engine may not start.
●If attempting to restart the engine imme-
diately after turning the engine switch off, the engine may not start in some cases. After turning the engine switch off, please
wait a few seconds before restarting the engine.
■Customization
If the smart entry & start system has been deactivated in a customized setting, refer to P.389.
WARNING
■When starting the engine
Always start the engine while sitting in the driver’s seat. Do not depress the accelerator pedal while starting the
engine under any circumstances. Doing so may cause an accident result-ing in death or serious injury.
■Caution while driving
If engine failure occurs while the vehicle is moving, do not lock or open the doors
until the vehicle reaches a safe and com- plete stop. Activation of the steering lock in this circumstance may lead to an acci-
dent, resulting in death or serious injury.
NOTICE
■When starting the engine
●Do not race a cold engine.
●If the engine becomes difficult to start
or stalls frequently, have your vehicle checked by any authorized Lexus retailer or Lexus authorized repairer,
or any reliable repairer immediately.

165
4
-$@-$I@0.@0.&@ &&

4-2. Driving procedures
Driving
1Stop the vehicle completely.
2 If the parking brake is in manual
mode, set the parking brake.
( P.187)
3 Shift the shift position to P.
( P.175)
Check that the shift position indicator
shows P. ( P.175)
4Press the engine switch.
The engine will stop, and the meter display will be extinguished (the shift position indi-
cator will be extinguished a few seconds after the meter display).
5 Check that “ACCESSORY” or
“IGNITION ON” is not shown on
the meter.
■Automatic P position selection function
 P.176
Modes can be changed by pressing
the engine switch with the brake pedal
released. (The mode changes each
time the switch is pressed.)
NOTICE
■Symptoms indicating a malfunction with the engine switch
If the engine switch seems to be operat- ing somewhat differently than usual, such as the switch sticking slightly, there may
be a malfunction. Contact any autho- rized Lexus retailer or Lexus authorized repairer, or any reliable repairer immedi-
ately.
Stopping the engine
WARNING
■Stopping the engine in an emergency
●If you want to stop the engine in an
emergency while driving the vehicle, press and hold the engine switch for more than 2 seconds, or press it briefly
3 times or more in succession. ( P.360) However, do not touch the engine
switch while driving except in an emer- gency. Turning the engine off while driving will not cause loss of steering
or braking control, however, power assist to the steering will be lost. This will make it more difficult to steer
smoothly, so you should pull over and stop the vehicle as soon as it is safe to do so.
●If the engine switch is operated while the vehicle is running, a warning mes-
sage is shown on the multi-information display and a buzzer sounds.
●When restarting the engine after an emergency shutdown, press the engine switch.
Changing engine switch modes

168
-$@-$I@0.@0.&@ &&

4-2. Driving procedures
on the multi-information display, read the message and follow the instructions.
■When the ambient temperature is low, such as during winter driving conditions
●When starting the hybrid system, the flashing time of the “READY” indicator
may be long. Leave the vehicle as it is until the “READY” indicator is steady on, as steady means the vehicle is able to move.
●When the hybrid battery (traction bat-tery) is extremely cold (below approxi-
mately -30°C [-22°F]) under the influence of the outside temperature, it may not be possible to start the hybrid
system. In this case, try to start the hybrid system again after the temperature of the hybrid battery increases due to the out-
side temperature increase etc.
■Sounds and vibrations specific to a hybrid vehicle
 P.64
■If the 12-volt battery is discharged
The hybrid system cannot be started using
the smart entry & start system. Refer to P.393 to restart the hybrid system.
■Electronic key battery depletion
 P.112
■Conditions affecting operation
 P.124
■Note for the entry function
 P.124
■Steering lock function
●After turning the power switch off and opening and closing the doors, the steer-
ing wheel will be locked due to the steer- ing lock function. Operating the power switch again automatically cancels the
steering lock.
●When the steering lock cannot be
released, “Push power switch while turn- ing the steering wheel in either direction” will be displayed on the multi-information
display. Press the power switch shortly and firmly while turning the steering wheel left and
right.
●To prevent the steering lock motor from
overheating, the motor may be sus- pended if the hybrid system is turned on and off repeatedly in a short period of
time. In this case, refrain from operating the power switch. After about 10 sec-onds, the steering lock motor will resume
functioning.
■If there is a malfunction in the smart entry & start system
If “Entry & Start System Malfunction” is dis- played on the multi-information display, the system may be malfunctioning. Have the
vehicle inspected by any authorized Lexus retailer or Lexus authorized repairer, or any reliable repairer immediately.
■If the “READY” indicator does not come
on
In the event that the “READY” indicator does not come on even after performing the proper procedures for starting the vehi-
cle, contact any authorized Lexus retailer or Lexus authorized repairer, or any reliable repairer immediately.
■If the hybrid system is malfunctioning
 P.68
■Electronic key battery
 P.349
■Operation of the power switch
●If the switch is not pressed shortly and
firmly, the power switch mode may not change or the hybrid system may not start.
●If attempting to restart the hybrid system immediately after turning the power
switch off, the hybrid system may not start in some cases. After turning the power

169
4
-$@-$I@0.@0.&@ &&

4-2. Driving procedures
Driving
switch off, please wait a few seconds before restarting the hybrid system.
■Customization
If the smart entry & start system has been deactivated in a customized setting, refer to P.389.
1 Stop the vehicle completely.
2 If the parking brake is in manual
mode, set the parking brake.
( P.187)
3 Shift the shift position to P.
( P.182)
Check that the shift position indicator shows P. ( P.181)
4Press the power switch.
The hybrid system will stop, and the meter display will be extinguished (the shift posi-tion indicator will be extinguished a few
seconds after the meter display).
5 Check that “ACCESSORY” or
“IGNITION ON” is not shown on
the meter.
■Automatic P position selection function
 P.182
WARNING
■When starting the hybrid system
Always start the hybrid system while sit- ting in the driver’s seat. Do not depress the accelerator pedal while starting the
hybrid system under any circumstances. Doing so may cause an accident result-ing in death or serious injury.
■Caution while driving
If hybrid system failure occurs while the vehicle is moving, do not lock or open the
doors until the vehicle reaches a safe and complete stop. Activati on of the steering lock in this circumstance may lead to an
accident, resulting in death or serious injury.
NOTICE
■When starting the hybrid system
If the hybrid system becomes difficult to start, have your vehicle checked by any authorized Lexus retailer or Lexus
authorized repairer, or any reliable repairer immediately.
■Symptoms indicating a malfunction with the power switch
If the power switch seems to be operat- ing somewhat differently than usual, such
as the switch sticking slightly, there may be a malfunction. Contact any autho-rized Lexus retailer or Lexus authorized
repairer, or any reliable repairer immedi- ately.
Stopping the hybrid system
WARNING
■Stopping the hybrid system in an emergency
●If you want to stop the hybrid system in an emergency while driving the vehi-cle, press and hold the power switch
for more than 2 seconds, or press it briefly 3 times or more in succession. ( P.360)
However, do not touch the power switch while driving except in an emer- gency. Turning the hybrid system off
while driving will not cause loss of steering or braking control, however, power assist to the steering will be lost.
This will make it more difficult to steer smoothly, so you should pull over and stop the vehicle as soon as it is safe to
do so.
●If the power switch is operated while the vehicle is running, a warning mes-sage is shown on the multi-information
display and a buzzer sounds.

193
4
-$@-$I@0.@0.&@ &&

4-3. Operating the lights and wipers
Driving
Pull the lever toward you and release it
again to turn off the lights.
When any of the following conditions is
met, while the headlights (low beam)
are on, the cornering lights will addi-
tionally turn on and light up the direc-
tion of movement for the vehicle. This is
to ensure excellent visibility when
either driving at intersections or park-
ing at night.
 The steering wheel is operated
 The turn signal lever is operated
 The shift position is in R (both left
and right side cornering lights)
■Cornering light control
●The lights illuminate when the vehicle speed is approximately 30 km/h (19
mph) or less. However, the lights turn off when the vehicle speed increases to approximately 35 km/h (22 mph) or
more.
●After the lights remain illuminated for 30
minutes, they automatically turn off.
*:If equipped
1 Push the lever away from you with
the headlight switch in the or
position.
2 Press the Automatic High Beam
switch.
Cornering lights
Automatic High Beam*
The Automatic High Beam uses an
in-vehicle camera sensor to assess
the brightness of streetlights, the
lights of a vehicle ahead, etc., and
automatically turns the high beam
on or off as necessary.
WARNING
■Limitations of the Automatic High Beam
Do not rely on the Automatic High Beam. Always drive safely, taking care to observe your surroundings and turning
the high beam on or off manually if nec- essary.
■To prevent incorrect operation of the Automatic High Beam system
Do not overload the vehicle.
Activating the Automatic High
Beam system

210
-$@-$I@0.@0.&@ &&

4-5. Using the driving support systems
*: If equipped
■Pre-collision warning
When the system determines that the
possibility of a frontal collision is high, a
buzzer will sound and a warning mes-
sage will be displayed on the multi-
information display to urge the driver
to take evasive action.
■Pre-collision brake assist
When the system determines that the
possibility of a frontal collision is high,
the system applies greater braking
force in relation to how strongly the
brake pedal is depressed.
■Pre-collision braking
When the system determines that the
possibility of a frontal collision is high,
the system warns the driver. If the sys-
tem determines that the possibility of a
frontal collision is extremely high, the
brakes are automatically applied to
help avoid the collision or reduce the
collision speed.
■Suspension control
When the system determines that the
possibility of a frontal collision is high,
the Adaptive Variable Suspension sys-
tem ( P.262) will control the damping
force of the shock absorbers to help
maintain an appropriate vehicle pos-
ture.
■Steering control (if equipped)
When the system determines that the
possibility of a frontal collision is high
PCS (Pre-Collision System)*
The pre-collision system uses a
radar sensor and camera sensor to
detect vehicles and pedestrians*1 in
front of your vehicle. When the sys-
tem determines that the possibility
of a frontal collision with a vehicle
or pedestrian is high, a warning
operates to urge the driver to take
evasive action and the potential
brake pressure is increased to help
the driver avoid the collision. If the
system determines that the possi-
bility of a frontal collision with a
vehicle or pedestrian is extremely
high, the brakes are automatically
applied to help avoid the collision or
help reduce the impact of the colli-
sion.
The pre-collision system can be dis-
abled/enabled and the warning tim-
ing can be changed. ( P.212)
*1: Depending on the region in which
the vehicle was sold, the pedestrian
detection function may not be avail-
able. Contact any authorized Lexus
retailer or Lexus authorized repairer,
or any reliable repairer for details.
System functions